11 GHz FDD Backhaul Radio Models: AF11FXH, AF11FXL Introduction Thank you for purchasing the Ubiquiti Networks airFiber AF11FX. This Quick Start Guide is designed to guide you through installation. Package Contents airFiber AF11FX Duplexer1 Cable Ties
(Qty. 2) airFiber Gigabit PoE Power Cord Quick Start Guide
(50V, 1.2A) 11 GHz FDD Backhaul Radio Models: AF-11FX-H, AF-11FX-L 1. Highband Duplexer (AF11FXH) or lowband Duplexer (AF11FXL) TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable is designed for outdoor installations. It is the customers responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements. Antenna Compatibility The airFiber AF11FX radio is designed for use with the following airFiber X antenna models:
AF11G361 Installation Requirements Clear line of sight between airFiber radios Vertical mounting orientation Mounting point:
At least 1 m below the highest point on the structure For tower installations, at least 3 m below the top of thetower Ground wires min. 10 AWG (5 mm2) and max. length:
1m. Asa safety precaution, ground the airFiber radio to grounded masts, poles, towers, or grounding bars. WARNING: Failure to properly ground your airFiber radio will void your warranty.
(Recommended) 2 Outdoor Gigabit PoE surge protectors Note: For guidelines about grounding and lightning protection, follow your local electrical regulatory codes.
(Optional) DC power source (if not using PoE) Outdoor, shielded Category 6 (or above) cabling and shielded RJ45 connectors are required for all wired Ethernet connections. 2 Check your local/regional regulations for the maximum antenna gain allowed for your application. Hardware Overview CH0 Port:
Connects to AF-11G36 Antenna Duplexer Shroud CH1 Port
(Under Cap) LED Panel Port Cover Ports Management Port Data Port VDC Reset Button Management Port 10/100 Mbps, secured Ethernet port for configuration. In-Band Management is enabled by default in the airFiber Configuration Interface. When In-Band Management is disabled, the MGMT port is the only port that can monitor, configure, and/or update firmware. Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is already poweredon. Data Port Gigabit PoE port for handling all user traffic and powering the device. VDC The VDC terminal block, labeled (+) and (-), is used to power the AF11FX using 50VDC instead of PoE. Duplexer Ports AF-11FX Radio
(Duplexer Shroud removed) TX0 RX0 RX1 TX1 TX0, RX0 Transmit and Receive SMA ports for lowband Duplexer (SISO mode) or highband Duplexer (MIMO mode). RX1, TX1 Receive and Transmit SMA ports for highband Duplexer (MIMO mode only). Duplexer N Connector SMA Port SMA Port N Connector Female Ntype connector into which the antenna cable is plugged. SMA Port Highband and lowband channel SMA ports. LEDs Signal LEDs Signal 4 LED will light blue when on. Signal 3 LED will light green when on. Signal 2 LED will light yellow when on. Signal 1 LED will light red when on. Bootup to airOS When powering on, the Power, MIMO, LINK, and Signal 1-4 LEDs light on. Once the CPU code takes over, the MIMO, LINK, and Signal 1-3 LEDs turn off. Signal 4 LED remains on to indicate the boot sequence is underway. Initializing airFiber Software When the airFiber application begins to boot under airOS, the Signal 4 LED goes from solidly on to a 2.5 Hz flash. This continues until the AF11FX is fully booted. Signal Level Once fully booted, the Signal 1-4 LEDs act as a bar graph showing how close the AF11FX is to ideal aiming. This is autoscaled based on the link range, the antenna gains, and the configured TX power of the remote AF11FX. Each Signal LED has three possible states: On, Flashing, and Off. All Signal LEDs would be solidly on in an ideal link. If the link has a 1 dB loss, the Signal4 LED will flash; a 2 dB loss and the Signal 4 LED will turn off. The full bar graph LED states are shown below. dB loss 0 1 1 1 1 1 2 3 4 5 6 7 8 9 10 11 12 13 F 1 1 1 0 1 1 1 0 F 1 1 0 0 1 1 0 0 F 1 0 0 F 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 F 0 0 0 F 0 0 0 F 0 0 0 0 0 = Off, 1 = On, F = Flashing Additional LEDs LED State Off Status RF Off Short Flash*
Syncing LINK Normal Flash*
Beaconing Long Flash*
Registering MIMO On Off On Off Operational Radio configured in SISO mode Radio configured in MIMO mode No Ethernet Link MGMT On Ethernet Link Established Random Flashing Ethernet Activity Off On DATA No Ethernet Link Ethernet Link Established Random Flashing Ethernet Activity Off On No Power Powered On
* Short Flash (1:3 on/off cycle) Normal Flash (1:1 on/off cycle) Long Flash (3:1 on/off cycle) Installation Overview We recommend that you configure your paired AF11FX radios before site installation. The overview below summarizes the installation procedure, and the subsequent sections provide detailed installation information. Install the Duplexer(s) in the AF11FX radio. Connect power (PoE or DC) to the AF11FX and connect your computer to the MGMTport. Configure the AF11FX. Install a ground wire and mount the AF11FX on the airFiber AF11G36 antenna (or a compatible antenna). At the installation site, install the antenna with the mounted AF11FX radio (see the antennas Quick Start Guide for installation instructions). Establish and optimize the RF link. Installing the Duplexer Install the included Duplexer as follows:
1. Loosen the screw on top of the Duplexer Shroud and remove the Duplexer Shroud. 2. Insert the TX and RX ports of the Duplexer into the TX0 and RX0 ports of the AF11FX radio. If you will be using the AF11FX in SISO mode, go to step 5. 3. 4. To use the AF11FX in MIMO mode:
a. Attach the second Duplexer (not included) to the AF11FX radios TX1 and RX1 ports. Note: The Duplexers must be installed in reverse order on opposite sides of the link. b. Remove the cap on the top right side of the AF11FX. 5. Reattach the Duplexer Shroud to the AF11FX radio. Connecting Power Follow the instructions for the source of power that you are using: Power over Ethernet or DC Power. Power over Ethernet 1. Lift the release latch on the bottom of the AF11FX and slide the Port Cover off. 2. Connect an Ethernet cable to the DATA port. 3. Connect the Ethernet cable from the DATA port of the AF11FX to the POE port of the adapter. WARNING: Use only the included adapter, model GP-C500-120G. Failure to do so can damage the unit and void the product warranty. 4. Connect the Power Cord to the adapters power port. Connect the other end of the Power Cord to a poweroutlet. DC Power To use DC input power instead of PoE, follow these steps:
1. Lift the release latch on the bottom of the AF11FX and slide the Port Cover off. 2. Connect a DC power cable to the Terminal Block. 3. Connect the other end of the DC power cable to a DC power supply. 4. Connect the DC power supply to its source. airFiber Configuration The instructions in this section explain how to access the airFiber Configuration Interface and configure the following settings:
Wireless Mode Configure one AF11FX as the Master and the other as the Slave. Frequency Setting The TX Frequency and RX Frequency settings must be the reverse of each other on both the Master and the Slave. 1. Connect an Ethernet cable from your computer to the MGMT port on the AF11FX. 2. Configure the Ethernet adapter on your computer with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser. Type http://192.168.1.20 in the address field and press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login. 5. Click the Wireless tab. 6. Configure the Basic Wireless Settings:
a. For one AF11FX, select Master as the Wireless Mode. For the other AF11FX, keep the default,Slave. b. Enter a name in the Link Name field. This should be the c. same on both the Master and the Slave. If needed, change the Channel Bandwidth, Output Power and/or Maximum Modulation Rate settings. 7. Configure the TX Frequency and RX Frequency. Note: One airFiber radios TX Frequency is the other radios RX Frequency, and vice versa. 8. Configure the Wireless Security:
a. Select the AES Key Type, HEX or ASCII. b. For the Key field:
HEX Enter 16 bytes (eight, 16bit hexadecimal digits:
09, AF, or af). You can omit zeroes and use colons, similar to the IPv6 format. Note: The airFiber Configuration Interface supports IPv6 formats excluding dotted quad and :: (doublecolon) notation. ASCII Enter a combination of alphanumeric characters (09, AZ, or az). 9. Click Change and then click Apply. 10. In-Band Management is enabled by default, so each airFiber radio must have a unique IP Address. (If the airFiber radios use the same IP Address, you may lose access to the airFiber radios via the DATA ports.) Click the Network tab. a. For the Management IP Address option:
DHCP Keep the default, DHCP, to use DHCP reservation on your router to assign a unique IPAddress. Static Change the IP Address, Netmask, and other settings to make them compatible with your network. b. Click Change and then click Apply. 11. Disconnect the Ethernet cable from the MGMT port on the AF11FX. Configuration of the AF11FX radio is complete. Repeat the instructions in the airFiber Configuration section on the other AF11FX radio. Hardware Installation Install a Ground Wire 1. Remove the nut from the Ground Bonding Point located on the back of the AF11FX. Ground Bonding Point 2. Attach a ground wire (min. 10 AWG or 5 mm2) to the lug and replace the nut to secure the wire.
*640-00256-01*
640-00256-01 3. At the installation site, secure the other end of the ground wire to a grounded mast, pole, tower, or grounding bar. WARNING: Failure to properly ground your airFiber radio will void your warranty. Note: The ground wire should be as short as possible and no longer than one meter in length. Mount to the airFiber Antenna Follow the instructions in this section to mount the AF11FX to an airFiber AF11G36 antenna:
1. Attach the airFiber X radio to the antenna by aligning the four tabs on the back of the radio with the slots of the radio mount. Then slide the radio down to lock it into place. 2. Attach the RF connector labeled V to the radios CH0 port. Ifyou are using MIMO mode, attach the RF connector labeled H to the radios CH1 port. 3. Attach the protective shroud. a. Align the hash mark on the top of the shroud with the notch on the dish antenna. b. Rotate the shroud clockwise until it locks into place. Connecting Data Note: Skip this section if you are using DC power which was already connected as described in DC Power. 1. Lift the release latch on the bottom of the AF11FX and slide the Port Cover off. 2. Connect an outdoor, shielded Ethernet cable to the DATAport. 3. 4. If you are using DC power, connect the other end of the Ethernet cable to your LAN. Connection is complete. If you are using Power over Ethernet:
a. Connect the Ethernet cable from the DATA port of the AF11FX to the POE port of the adapter. WARNING: Use only the included adapter, model GP-C500-120G. Failure to do so can damage the unit and void the product warranty. b. Connect an Ethernet cable from your LAN to the adapters LAN port. c. Connect the Power Cord to the adapters power port. Connect the other end of the Power Cord to a power outlet. Surge Protection For added protection, install two surge suppressors, such as the Ubiquiti Ethernet Surge Protector, model ETHSP, at the end of each link. Install the first surge protector within one meter of the airFiber DATA port, and install the second surge protector at the ingress point of the location housing the wired network equipment. AF-11FX Mounted on AF-11G36 m 1
. x a M ETH-SP ETH-SP Ground to Pole, Tower, or Grounding Block:
Max. 1 m from AF-11FX EdgeRouter airFiber PoE Adapter Power Source Alignment Tips To accurately align the airFiber radios for best performance, you MUST align only one end of the link at a time. You may need to use additional hardware to compensate for issues such as the improper orientation of a mounting pole or significant elevation differences between airFiber radios. Establishing a Link Adjust the positions of the Master and the Slave to establish a link. The following section features the airFiber X antenna, AF11G36:
Note: The Master must be aimed first at the Slave because the Slave does not transmit any RF signal until it detects transmissions from the Master. 1. Master Visually aim the Master at the Slave. To adjust the Masters position, adjust the azimuth and the elevation. Adjust the azimuth:
a. Loosen the four flange nuts on the two pole clamps. b. Rotate the antenna to point towards the other end of the link. c. Tighten the four flange nuts on the two pole clamps. Adjust the elevation angle:
a. Loosen the six hex head bolts to so that the washers can spin freely by hand. b. Tighten or loosen the Elevation Adjustment Bolt to set the desired tilt. c. Tighten the six hex head bolts. Elevation Adjustment Bolt Note: Do NOT make simultaneous adjustments on the Master and Slave. 2. Slave Visually aim the Slave at the Master. To adjust the Slaves position, adjust the azimuth and elevation as described in step 1. 3. Check to see if a link is established. Ensure that the LINK LED is solidly lit green and the Signal LEDs of the Slave are displaying signal levels. MIMO 4. Slave Aim the Slave at the Master to achieve the strongest signal level on the Master. Note: Refer to the Signal LEDs section for details on the signal values. Note: Maximum signal strength can best be achieved by iteratively sweeping through both azimuth and elevation. 5. Master Aim the Master at the Slave to achieve the strongest signal level on the Slave. 6. Repeat steps 4 and 5 until you achieve an optimal link, with all four Signal LEDs solidly lit. This ensures the best possible data rate between the airFiber radios. 7. Lock the alignment on both airFiber antennas by tightening all the nuts and bolts. 8. Observe the Signal LEDs of each airFiber radio to ensure that the values remain constant while tightening the nuts and bolts. If any LED value changes during the locking process, loosen the nuts and bolts, finalize the alignment of each airFiber antenna again, and retighten the nuts and bolts. Installer Compliance Responsibility Devices must be professionally installed and it is the professional installers responsibility to make sure the device is operated within local country regulatory requirements. The Output Power, Antenna Gain, Cable Loss, TX Frequency and RX Frequency fields are provided to the professional installer to assist in meeting regulatory requirements. Specifications Dimensions Weight RF Connectors Power Supply Power Method Supported Voltage Range Certifications Wind Loading Wind Survivability Mounting Operating Temperature Networking Interface Data Port Management Port System Processor Maximum Throughput Encryption OS Wireless Modes airFiber AF11FX 327 x 112 x 86 mm (12.87 x 4.41 x 3.39") 2.26 kg (5.0 lb)
(4) RPSMA Weatherproof, Two per Chain:
TX0, RX0 (CH0) and TX1, RX1 (CH1)
(2) NType Waterproof, One per Duplexer 50V, 1.2A PoE Gigabit Adapter (Included) Passive Power over Ethernet or DC Power Block 4258VDC FCC 47 CFR Part 101 480 N @ 200 km/hr (108 lbf @ 125 mph) 200 km/hr (125 mph) Enlarged airFiber X Mount 40 to 55 C (40 to 131 F)
(1) 10/100/1000 Ethernet Port
(1) 10/100 Ethernet Port INVICTUS IC 1.2+ Gbps 128bit AES airOS F Master/Slave Radio Operating Frequency Max. Conducted TX Power Frequency Accuracy Channel Bandwidth 10.711.7 GHz1 30 dBm1 1 ppm 3.5/5/7/10/14/20/28/30/40/50/56 MHz Selectable2 Programmable Uplink and Downlink Duty Cycles 1 Depends on Regulatory Region 2 Channel widths may vary according to country/region regulations. Compliance FCC This device has been verified by Ubiquiti Networks as being in compliance with the requirements of the rules of the Federal Communications Commission (FCC), 47 C.F.R. Part 101, and may not be operated without a station license. In the United States such licenses are issued by the FCC to entities other than agencies of the United States government. Federal government agencies are licensed by the National Telecommunications and Information Administration (NTIA) acting upon the recommendation of the Interdepartment Radio Advisory Committee (IRAC). RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 186 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilises pour ce transmetteur doivent tre install en considrant une distance de sparation de toute personnes dau moins 186cm et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur. Australia and New Zealand Warning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Deutsch Die Europische Richtlinie 2012/19/EU verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Espaol La Directiva 2012/19/UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto. Franais La directive europenne 2012/19/UE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italiano La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity esky
[Czech]
Dansk
[Danish]
Nederlands
[Dutch]
English Eesti
[Estonian]
Suomi
[Finnish]
Franais
[French]
Deutsch
[German]
[Greek]
Magyar
[Hungarian]
slenska
[Icelandic]
Italiano
[Italian]
Latviski
[Latvian]
UBIQUITI NETWORKS tmto prohlauje, e toto UBIQUITI NETWORKS zazen, je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Hermed, UBIQUITI NETWORKS, erklrer at denne UBIQUITI NETWORKS enhed, er i overensstemmelse med de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hierbij verklaart UBIQUITI NETWORKS, dat deze UBIQUITI NETWORKS apparaat, in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI NETWORKS device, is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Kesolevaga UBIQUITI NETWORKS kinnitab, et antud UBIQUITI NETWORKS seade, on vastavus olulistele nuetele ja teistele asjakohastele stetele direktiivi 1999/5/E. Tten UBIQUITI NETWORKS vakuuttaa, ett tm UBIQUITI NETWORKS laite, on yhdenmukainen olennaisten vaatimusten ja muiden sit koskevien direktiivin 1999/5/EY. Par la prsente UBIQUITI NETWORKS dclare que lappareil UBIQUITI NETWORKS, est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Hiermit erklrt UBIQUITI NETWORKS, dass sich dieses UBIQUITI NETWORKS Gert, in bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet.
, UBIQUITI NETWORKS, UBIQUITI NETWORKS, 1995/5/. Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a UBIQUITI NETWORKS kszlk megfelel az alapvet kvetelmnyeknek s ms vonatkoz 1999/5/EK irnyelv rendelkezseit. Hr, UBIQUITI NETWORKS, v yfir a etta UBIQUITI NETWORKS tki er samrmi vi grunnkrfur og nnur vieigandi kvi tilskipun 1999/5/EB. Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo UBIQUITI NETWORKS, conforme ai requisiti essenziali ed alle altre disposizioni pertinenti della direttiva 1999/5/CE. Ar o, UBIQUITI NETWORKS, deklar, ka UBIQUITI NETWORKS ierce, ir saska ar btiskajm prasbm un citiem attiecgiem noteikumiem Direktv 1999/5/EK. Lietuvikai
[Lithuanian]
UBIQUITI NETWORKS deklaruoja, kad is UBIQUITI NETWORKS renginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Malti
[Maltese]
Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz UBIQUITI NETWORKS huwa konformi mar-rekwiiti essenzjali u dispoizzjonijiet rilevanti orajn ta Direttiva 1999/5/KE. Norsk
[Norwegian]
Herved UBIQUITI NETWORKS, erklrer at denne UBIQUITI NETWORKS enheten, er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktiv 1999/5/EF. Polski
[Polish]
Niniejszym, Ubiquiti Networks, owiadcza, e urzdzenie UBIQUITI NETWORKS, jest zgodny z zasadniczymi wymaganiami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/WE. Portugus
[Portuguese]
UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Romn
[Romanian]
Slovensky
[Slovak]
Espaol
[Spanish]
Svenska
[Swedish]
Prin prezenta, UBIQUITI NETWORKS declar c acest dispozitiv UBIQUITI NETWORKS este n conformitate cu cerinele eseniale i alte prevederi relevante ale Directivei 1999/5/CE. Tmto UBIQUITI NETWORKS, prehlasuje, e toto UBIQUITI NETWORKS zariadenie, je v slade so zkladnmi poiadavkami a almi relevantnmi ustanoveniami smernice 1999/5/ES. Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Hrmed UBIQUITI NETWORKS, intygar att denna UBIQUITI NETWORKS enhet r i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. w w w . u b n t . c o m Online Resources Support support.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com 2016 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, airOS, EdgeRouter, INVICTUS, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners. AI081116