submitted | available | document details (if available) | source link |
---|---|---|---|
PowerBeam PBE-2AC-400-Gen2 Quick Start Guide N Bautista Adobe PDF Library 15.0 |
various | Users Manual | Users Manual | 4.54 MiB |
2.4 GHz High-Performance airMAX ac Bridge with Dedicated Wi-Fi Management Model: PBE-2AC-400 Introduction Thank you for purchasing the Ubiquiti Networks PowerBeamAC . This Quick Start Guide is designed to guide you through installation and also includes warranty terms. If you want to add a radome to enclose the Dish Reflector, UbiquitiNetworks offers the PowerBeam Radome, 400 mm, modelPBE-RAD-400 as an optional accessory. Product details are available on our website at www.ubnt.com Package Contents Dish Reflector Antenna Feed Rear Housing 20 10 0 10 Dish Bracket Pole Clamp U-Bolt Flange Nuts
(Qty. 2) Gigabit PoE (24V, 0.5A) with Mounting Bracket Power Cord Quick Start Guide 2.4 GHz High-Performance airMAX ac Bridge with Dedicated Wi-Fi Management Model: PBE-2AC-400-Gen2 TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable is designed for outdoor installations. It is the customers responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements. Installation Requirements 13 mm wrench Shielded Category 5 (or above) cabling with drain wire should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the PowerBeam and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground. PBE-2AC-400 ES-8-150W ETH-SP ETH-SP To LAN Hardware Overview Bottom View Technology Antenna Feed Ethernet Port Reset Button Release Button Dish Reflector Dish Bracket Alignment Pins Rear Housing Release Button Slot Cable Door Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the PowerBeam is already poweredon. Alternatively, the PowerBeam may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter. Release Button After you assemble the PowerBeam, check the Release button; it should be fully engaged in the Release Button Slot of the Rear Housing. This ensures that the Antenna Feed is locked into place. If you need to remove the Antenna Feed, you must depress the Release button first. LEDs Power The Power LED will light blue when the device is connected to a power source. Ethernet The Ethernet LED will light steady blue when an active Ethernet connection is made and flash when there is activity. Signal In airOS, you can modify the threshold value for the wireless signal strength LEDs on the Wireless tab under Signal LED Thresholds. Each LED will light when the wireless signal strength is equal to or greater than the LEDs threshold value. The default threshold values for these LEDs are shown below:
-65 dBm -73 dBm -80 dBm -94 dBm Application Examples The PowerBeam mounted outdoors with the Dish Reflector installed provides directional outdoor coverage (gain is reflector-dependent). The PowerBeam mounted outdoors without the Dish Reflector installed provides outdoor-to-indoor coverage using the 3 dBi Antenna Feed only. Installation 1. Align and insert the tabs of the Dish Bracket into the slots of the Dish Reflector. Rotate the Dish Bracket counter-clockwise until the tabs lock into place. 0 1 0 0 1 0 2 2. Line up the Alignment Pins of the Rear Housing with the alignment holes of the Dish Bracket. Insert the pins and push until they lock intoplace. 0 1 0 0 1 0 2 3. Push in the sides of the Cable Door and detach it from the Rear Housing. 20 10 0 10 4. Attach the Antenna Feed:
a. Insert the Antenna Feed into the Rear Housing, and push until it locks into place with a click. b. Lightly pull the Antenna Feed to ensure that it is locked into place and the Release button is fully engaged. Release Button Bottom View 5. Connect the Ethernet cable:
a. Connect an Ethernet cable to the Ethernet Port of the Antenna Feed. b. Re-attach the Cable Door to the Rear Housing. 20 10 0 10 6. Slide the Pole Clamp onto the Dish Bracket. 2010100 7. Insert the U-Bolt into the Pole Clamp and Dish Bracket. Secure each end of the U-Bolt with a Flange Nut. 20 10 0 10 25 N m Note: The mounting assembly can accommodate a 32 - 56 mm pole. 8. Optional: If you have the PowerBeam Radome (optional accessory), then align the arrows on the bottoms of the Radome and Dish Reflector so the Drain Holes on the Radome point downward. Snap the Radome onto the Dish Reflector. Connect the power using one of the following options:
Using the included Gigabit PoE Adapter: Go to Connecting to the PoE Adapter. Using a separate PoE switch: Connect the Ethernet cable from the PowerBeams Ethernet port to a PoE-enabled Ethernet port on the switch. WARNING: The switch port must comply with the power specifications listed in the Specifications section of this Quick Start Guide. Connecting to the PoE Adapter 1. Connect the Ethernet cable from the PowerBeams Ethernet port to the POE port of the Gigabit PoE adapter. 2. Connect an Ethernet cable from your LAN to the adapters LAN port. 3. Connect the Power Cord to the adapters power port. Connect the other end of the Power Cord to a power outlet. Mounting the PoE Adapter (Optional) 1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included). 3. Align the adapters slots with the tabs of the PoE Mounting Bracket, and then slide the adapterdown. Accessing airOS via Wi-Fi Verify connectivity in the airOS Configuration Interface. There are two methods, the U Mobile App and Web Portal. Both are available for 15 minutes immediately after you power on the PowerBeam. If necessary, you can power cycle the PowerBeam to re-enable its Wi-Fi. Proceed to the appropriate instructions:
U Mobile App 1. Download the U Mobile app from the AppStore (iOS) or Google Play (Android). 2. Connect your devices Wi-Fi to the PowerBeam SSID named: PBE-2AC-400:<MAC Address>
Note: Ensure that DHCP is enabled on your Wi-Fiadapter. 3. Launch the app 4. Tap the PowerBeam on the Connections scree 5. Tap Connect on the Login screen. 6. Select your Country and tap Done. 7. Customize your settings as needed.
*640-00213-03*
640-00213-03 Web Portal 1. Connect your devices Wi-Fi to the PowerBeam SSID named: PBE-2AC-400:<MAC Address>
Note: Ensure that your Wi-Fi connection has DHCP enabled. 2. Launch a web browser and go to: http://setup.ubnt.com 3. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login. Note: The Country setting for U.S. product versions is restricted to a choice of Canada, Puerto Rico, or the U.S. to ensure compliance with FCC/IC regulations. The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For additional details on the airOS Configuration Interface, refer to the User Guide available at www.ubnt.com/download/airmax Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Output Power field is provided to the professional installer to assist in meeting regulatory requirements. Specifications PBE-2AC-400 Dimensions Weight (Mount Included) Gain Networking Interface Enclosure Max. Power Consumption Power Supply Power Method Wind Survivability Wind Loading Certifications Mounting Operating Temperature Operating Humidity Shock and Vibrations 420 x 420 x 289 mm
(16.54 x 16.54 x 11.38") 1.795 kg (4.809 lb) 18 dBi
(1) 10/100/1000 Ethernet Port Outdoor UV Stabilized Plastic 7.5W 24V, 0.5A Gigabit PoE Adapter (Included) Passive PoE (Pairs 4, 5+; 7, 8 Return) 200 km/h (125 mph) 342.5 N @ 200 km/h (77 lbf @ 125 mph) CE, FCC, IC Pole Mounting Kit Included
-40 to 70 C (-40 to 158 F) 5 to 95% Noncondensing ETSI300-019-1.4 Worldwide USA Worldwide USA Operating Frequency (MHz) Management Radio (MHz) 2412 - 2472 2412 - 2462 5150 - 5250 U-NII-3: 5725 - 5850 Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturers label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet. a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire. b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death. c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection. e. Protective bonding must be installed in accordance with local national wiring rules and regulations. Limited Warranty UBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) warrants that the product(s) furnished hereunder (the Product(s)) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty Conditions The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks authorized representatives, or as approved by Ubiquiti Networks in writing;
has been painted, rebranded or physically modified in any way;
has been damaged due to errors or defects in cabling;
has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;
has been damaged or impaired as a result of using third party firmware;
has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or has not been received by Ubiquiti within 30 days of issuance of the RMA.
(II)
(III)
(IV)
(V)
(VI)
(VII) In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed. Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYERS EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyers selection of products (including the Products) for buyers application and/or failure of products (including the Products) to meet government or regulatory requirements. Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This radio transmitter (FCC ID: SWX-PBE2ACN) has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna Information: Dish antenna, Gain: 18 dBi Industry Canada CAN ICES-3(A)/NMB-3(A) This Class A digital apparatus complies with Canadian CAN ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter (IC: 6545A-PBE2ACN has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna Information: Dish antenna, Gain: 18 dBi CAN ICES-3(A)/NMB-3(A) Cet appareil numrique de la classe A est conforme la norme NMB-003 du Canada. Pour rduire le risque dinterfrence aux autres utilisateurs, le type dantenne et son gain doivent tre choisies de faon que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est ncessaire pour une communication russie. Cet appareil est conforme la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer dinterfrences et 2. Cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement du dispositif. Cet metteur radio (IC: 6545A-PBE2ACN) a t approuve par Industrie Canada pour lexploitation avec lantenne types numrs ci-dessous avec le gain maximal admissible et requis limpdance de lantenne pour chaque type dantenne indiqu. Types dantenne non inclus dans cette liste, ayant un gain suprieur au gain maximal indiqu pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Informations dantenne: Antenne parabolique, Gain: 18 dBi RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 28 cm from all persons and must not be lo-
cated or operating in conjunction with any other antenna or transmitter. Les antennes utilises pour ce transmetteur doivent tre install en considrant une distance de sparation de toute personnes dau moins 28cm et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur. Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Deutsch Die Europische Richtlinie 2012/19/EU verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Espaol La Directiva 2012/19/UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto. Franais La directive europenne 2012/19/UE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italiano La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity
[Bulgarian] UBIQUITI NETWORKS , UBIQUITI NETWORKS 2014/53/.
: www.ubnt.com/compliance Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa ovaj UBIQUITI NETWORKS ureaj u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedeoj internetskoj adresi: www.ubnt.com/compliance etina [Czech] Tmto UBIQUITI NETWORKS prohlauje, e typ rdiovho zazen e toto UBIQUITI NETWORKS zazen je v souladu se smrnic 2014/53/EU. pln znn EU prohlen o shod je k dispozici na tto internetov adrese: www.ubnt.com/compliance Dansk [Danish] Hermed erklrer UBIQUITI NETWORKS., at radioudstyrstypen denne UBIQUITI NETWORKS enhed er i overensstemmelse med direktiv 2014/53/EU. EUoverensstemmelseserklringens fulde tekst kan findes p flgende internetadresse:
www.ubnt.com/compliance Nederlands [Dutch] Hierbij verklaar ik, UBIQUITI NETWORKS, dat het type radioapparatuur UBIQUITI NETWORKS apparaat conform is met Richtlijn 2014/53/EU. De volledige tekst van de EUconformiteitsverklaring kan worden geraadpleegd op het volgende internetadres:
www.ubnt.com/compliance English Hereby, UBIQUITI NETWORKS declares that the radio equipment type this UBIQUITI NETWORKS device is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.ubnt.com/compliance Eesti keel [Estonian] Kesolevaga deklareerib UBIQUITI NETWORKS, et kesolev raadioseadme tp antud UBIQUITI NETWORKS seade vastab direktiivi 2014/53/EL nuetele. ELi vastavusdeklaratsiooni tielik tekst on kttesaadav jrgmisel internetiaadressil:
www.ubnt.com/compliance Suomi [Finnish] UBIQUITI NETWORKS vakuuttaa, ett radiolaitetyyppi ett tm UBIQUITI NETWORKS laite on direktiivin 2014/53/EU mukainen. EUvaatimustenmukaisuusvakuutuksen tysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.ubnt.com/compliance Franais [French] Le soussign, UBIQUITI NETWORKS, dclare que lquipement radiolectrique du type lappareil UBIQUITI NETWORKS est conforme la directive 2014/53/UE. Le texte complet de la dclaration UE de conformit est disponible ladresse internet suivante:
www.ubnt.com/compliance Deutsch [German] Hiermit erklrt UBIQUITI NETWORKS, dass der Funkanlagentyp dieses UBIQUITI NETWORKS Gert der Richtlinie 2014/53/EU entspricht. Der vollstndige Text der EUKonformittserklrung ist unter der folgenden Internetadresse verfgbar:
www.ubnt.com/compliance
[Greek] / UBIQUITI NETWORKS, UBIQUITI NETWORKS 2014/53/.
:
www.ubnt.com/compliance Magyar [Hungarian] UBIQUITI NETWORKS igazolja, hogy a UBIQUITI NETWORKS kszlk tpus rdiberendezs megfelel a 2014/53/EU irnyelvnek. Az EUmegfelelsgi nyilatkozat teljes szvege elrhet a kvetkez internetes cmen: www.ubnt.com/compliance slenska [Icelandic] Hr me lsir UBIQUITI NETWORKS yfir v a etta UBIQUITI NETWORKS tki er samrmi vi grunnkrfur og arar krfur, sem gerar eru tilskipun 2014/53/EU. Fullur texti ESB samrmisyfirlsing er a finna eftirfarandi netfangi: www.ubnt.com/compliance Italiano [Italian] Il fabbricante, UBIQUITI NETWORKS, dichiara che il tipo di apparecchiatura radio questo dispositivo UBIQUITI NETWORKS conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformit UE disponibile al seguente indirizzo Internet:
www.ubnt.com/compliance Latvi kalba [Latvian] Ar o UBIQUITI NETWORKS deklar, ka radioiekrta ka UBIQUITI NETWORKS ierce atbilst Direktvai 2014/53/ES. Pilns ES atbilstbas deklarcijas teksts ir pieejams d interneta vietn: www.ubnt.com/compliance Lietuvi kalba [Lithuanian] A, UBIQUITI NETWORKS, patvirtinu, kad radijo rengini tipas is UBIQUITI NETWORKS renginys atitinka Direktyv 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas iuo interneto adresu: www.ubnt.com/compliance Malti [Maltese] Bdan, UBIQUITI NETWORKS, niddikjara li dan ittip ta tagmir tarradju dan ilmezz UBIQUITI NETWORKS huwa konformi madDirettiva 2014/53/UE. Iddikjarazzjoni talkonformit tista tii kkonsultata minn www.ubnt.com/compliance Norsk [Norwegian] UBIQUITI NETWORKS erklrer herved at utstyret denne UBIQUITI NETWORKS enheten er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EUsamsvarserklringen er tilgjengelig p flgende internettadresse:
www.ubnt.com/compliance Polski [Polish] UBIQUITI NETWORKS niniejszym owiadcza, e typ urzdzenia radiowego urzdzenie UBIQUITI NETWORKS, jest zgodny z dyrektyw 2014/53/UE. Peny tekst deklaracji zgodnoci UE jest dostpny pod nastpujcym adresem internetowym:
www.ubnt.com/compliance Portugus [Portuguese] O(a) abaixo assinado(a) UBIQUITI NETWORKS declara que o presente tipo de equipamento de rdio este dispositivo UBIQUITI NETWORKS est em conformidade com a Diretiva 2014/53/UE. O texto integral da declarao de conformidade est disponvel no seguinte endereo de Internet: www.ubnt.com/compliance Romn [Romanian] Prin prezenta, UBIQUITI NETWORKS declar c tipul de echipamente radio acest dispozitiv UBIQUITI NETWORKS este n conformitate cu Directiva 2014/53/UE. Textul integral al declaraiei UE de conformitate este disponibil la urmtoarea adres internet:
www.ubnt.com/compliance Slovenina [Slovak] UBIQUITI NETWORKS tmto vyhlasuje, e rdiov zariadenie typu toto UBIQUITI NETWORKS zariadenie je v slade so smernicou 2014/53/E. pln E vyhlsenie o zhode je k dispozcii na tejto internetovej adrese: www.ubnt.com/compliance Slovenina [Slovenian] UBIQUITI NETWORKS potrjuje, da je tip radijske opreme ta naprava UBIQUITI NETWORKS skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.ubnt.com/compliance Espaol [Spanish] Por la presente, UBIQUITI NETWORKS declara que el tipo de equipo radioelctrico este dispositivo UBIQUITI NETWORKS es conforme con la Directiva 2014/53/UE. El texto completo de la declaracin UE de conformidad est disponible en la direccin Internet siguiente: www.ubnt.com/compliance Svenska [Swedish] Hrmed frskrar UBIQUITI NETWORKS att denna typ av radioutrustning denna UBIQUITI NETWORKS enhet verensstmmer med direktiv 2014/53/EU. Den fullstndiga texten till EUfrskran om verensstmmelse finns p fljande webbadress:
www.ubnt.com/compliance Online Resources Support help.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com w w w . u b n t . c o m Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA 2017 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, InnerFeed, PowerBeam, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple, the Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android, Google, Google Play, the Google Play logo and other marks are trademarks of Google Inc. All other trademarks are the property of their respective owners. NB062117
This product uses the FCC Data API but is not endorsed or certified by the FCC