| submitted | available | document details (if available) | source link |
|---|---|---|---|
| December 07 2017 |
| various | User Manual | Users Manual | 4.74 MiB | December 07 2017 |
micro 1080p Wireless IP Security Camera with Infrared Model: UVC-G3-MICRO Introduction Thank you for purchasing the Ubiquiti Networks UniFi Video Camera G3 Micro. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents UVC-G3-MICRO Camera Power Adapter 802.3af Instant PoE Adapter Instant PoE Cover Table Stand Wall Mounts
(Qty. 2) Instant PoE Mount Angle Mount Adhesives
(Qty. 2) Screws and Anchors
(Qty. 4) Cable Clips
(Qty. 8) micro 1080p Day/Night IP Security Camera with Infrared Model: UVC-G3-MICRO Quick Start Guide Before You Begin The UVC G3 Micro is designed to work with the UniFi Video
(v3.8 or above) controller software. The software may be hosted on either of the following:
The Ubiquiti Networks UniFiNVR appliance A Linux/Windows computer Note: The latest UniFi Video software is available for free download at: www.ubnt.com/download/unifivideo The UVC G3 Micro can be powered by either of the following methods:
Using the included Instant PoE Adapter connected to an 802.3af PoE-compliant switch Using the included Power Adapter Hardware Overview LED Reset Magnetic Base LED The LED will flash blue during bootup. When the camera is ready to connect to the Wi-Fi network, the LED pattern will flash two times accompanied by two beep tones. Once connected to the network, the LED will glow a breathing pattern. State Status Flashing Blue Device is Booting Up Steady Blue Connected to NVR Flashing White Connecting to Wi-Fi Steady White Ready for Configuration Flashing Red Cannot Connect to NVR Steady Red No Wi-Fi Connection Reset To reset network settings to factory defaults, press and hold the Reset button until the camera emits two fast tones. Installation The UVC G3 Micro can be mounted in four ways:
Magnetic For temporary installation Adhesive For fast, permanent installation Screws For secure installation Table For installing on a flat surface such as a table or shelf Magnetic Mount 1. Remove the Wall Mount from the Magnetic Base. Wall Mount 2. Attach the Power Adapter or Instant PoE Adapter to the MagneticBase. 3. Attach the camera and Magnetic Base directly to a metal fixture. Go to Connecting the Power. Adhesive Mount 1. If the Power Adapter cord or PoE Adapter Cord feeds through the wall, drill or cut a hole and feed the cord through it. 2. Remove the tab from the notch and attach the Wall Mount using the adhesive side.
*640-00321-01*
640-00321-01 3. Attach the Power Adapter or Instant PoE Adapter to the MagneticBase. 4. Attach the camera and Magnetic Base to the mount. If the power cord feeds through the Wall Mount, rotate the Magnetic Base to align the cord with the notch on the Wall Mount. Go to Connecting the Power. Cord on Wall Cord Through Wall Mount Screw Mount 1. If the circular connector on the Power Adapter or Instant PoE Adapter needs to connect through the wall, drill or cut a hole out and feed the power connector through it. Wall Mount Angle Mount 2. Use the Screws and Screw Anchors to fasten the Wall Mount or the Angle Mount. Wall Mount Angle Mount 3. Attach the Power Adapter to the Magnetic Base. 4. Attach the camera and Magnetic Base to the mount. If the power cord feeds through the Wall Mount, rotate the Magnetic Base so the cord aligns with the notch on the Wall Mount. Go to Connecting the Power. Cord on Wall Cord Through Wall Mount Table Mount 1. Feed the circular power connector (on the Power Adapter or Instant PoE Adapter) through the hole in the Table Stand. 2. Attach the circular power connector to the Magnetic Base of the camera. 3. Attach the Magnetic Base of the camera to the Table Stand by pressing it over the two notches and sliding it down. Connecting the Power Follow the instructions for your method of powering the camera: Power Adapter or Instant PoE Adapter. Power Adapter Plug the Power Adapter into an outlet. Note: Use the included Cable Clips to hold the power cord in place. Remove the paper backing on each clip to expose the adhesive and affix to a desired location. Instant PoE Adapter 1. Install the Instant PoE Mount on a wall using the included screw kit. Securing the Instant PoE Wall Mount Instant PoE Wall Mount Installed 2. Attach the circular power connector to the Magnetic Base of the camera. 3. Attach the Magnetic Base of the camera to the Instant PoE Mount by pressing it over the two notches and sliding it down. 4. Place the Instant PoE Cover over the Magnetic Base and onto the Instant PoE Wall Mount until it snaps into place. Then mount the camera to the Magnetic Base. Attach Instant PoE Cover Mount Camera to Magnetic Base 5. Connect the Ethernet cable from an 802.3af PoE switch to the PoE In port of the Instant PoE Adapter. Note: Use the included Cable Clips to hold the power cord in place. Remove the paper backing on each clip to expose the adhesive and affix to a desired location. Setting Up the UVC G3 Micro Ensure you are running the latest version of UniFi Video, v3.8 or above on the UniFi NVR or computer-based system. Download the UniFi Video User Guide for detailed information on how to set up and use UniFi Video:
www.ubnt.com/download/unifivideo UniFi Video Mobile App For quick setup, a mobile app is available. Install the UniFi Video app, and follow the on-screen instructions:
iOS: iTunes App Store Android: Google Play Store Specifications UVC-G3-Micro Dimensions Body Base Weight Body Base 51.38 x 41.97 mm (2.02 x 1.65") 36.0 x 17.3 mm (1.41 x 0.68) 65 g (2.29 oz) 31 g (1.09 oz) Enclosure Characteristics White Body with Black Front Surface Mounting Options Magnetic Base, Wall Mount, or Table Mount Networking Interface 802.11 a/b/g/n Dual-Band Wi-Fi; BT Lens Sensor View Angle LDC Off LDC On Night Mode Video Compression Resolution Max. Frame Rate Microphone Speaker Power Supply Supported Voltage Range Max. Power Consumption IR LEDs On IR LEDs Off Operating Temperature Operating Humidity Certifications 2.7 mm f2.2 1/3" 4MP Image Sensor with WDR 124 (H), 65 (V), 150 (D) 92 (H), 6 (V), 100 (D) Infrared LEDs with Built-In Light Sensor H.264 1080p HD (1920 x 1080) 30 FPS Yes (with Volume Control) Yes AC Adapter or Instant PoE Adapter 5V (4.85V - 5.35V) 3.5W 2W 0 to 35 C (32 to 95 F) 20 to 90% Noncondensing CE, FCC, IC Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturers label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet. a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire. b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death. c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection. e. Protective bonding must be installed in accordance with local national wiring rules and regulations. Limited Warranty UBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) warrants that the product(s) furnished hereunder (the Product(s)) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty Conditions The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks authorized representatives, or as approved by Ubiquiti Networks in writing;
has been painted, rebranded or physically modified in any way;
has been damaged due to errors or defects in cabling;
(II)
(III)
(IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;
has been damaged or impaired as a result of using third party firmware;
(V)
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed. Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYERS EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyers selection of products (including the Products) for buyers application and/or failure of products (including the Products) to meet government or regulatory requirements. Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This radio transmitter FCC ID: SWX-UVCG3M has been approved by FCC. Industry Canada CAN ICES-3(B)/NMB-3(B) This Class B digital apparatus complies with Canadian CAN ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter (IC: 6545A-UVCG3M) has been approved by Industry Canada. CAN ICES-3(B)/NMB-3(B) Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Pour rduire le risque dinterfrence aux autres utilisateurs, le type dantenne et son gain doivent tre choisies de faon que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est ncessaire pour une communication russie. Cet appareil est conforme la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer dinterfrences et 2. Cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement du dispositif. Cet metteur radio (IC: 6545A-UVCG3M) a t approuve par Industrie Canada. RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilises pour ce transmetteur doivent tre install en considrant une distance de sparation de toute personnes dau moins 20 cm et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Deutsch Die Europische Richtlinie 2012/19/EU verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Espaol La Directiva 2012/19/UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto. Franais La directive europenne 2012/19/UE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italiano La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity
[Bulgarian] UBIQUITI NETWORKS , UVC-G3-MICRO 2014/53/.
: www.ubnt.com/compliance Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa ovaj UVC-G3-MICRO ureaj u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedeoj internetskoj adresi: www.ubnt.com/compliance etina [Czech] Tmto UBIQUITI NETWORKS prohlauje, e typ rdiovho zazen e toto UVC-
G3-MICRO zazen je v souladu se smrnic 2014/53/EU. pln znn EU prohlen o shod je k dispozici na tto internetov adrese: www.ubnt.com/compliance Dansk [Danish] Hermed erklrer UBIQUITI NETWORKS., at radioudstyrstypen denne UVC-G3-MICRO enhed er i overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklringens fulde tekst kan findes p flgende internetadresse:
www.ubnt.com/compliance Nederlands [Dutch] Hierbij verklaar ik, UBIQUITI NETWORKS, dat het type radioapparatuur UVC-G3-MICRO apparaat conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-
conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres:
www.ubnt.com/compliance English Hereby, UBIQUITI NETWORKS declares that the radio equipment type this UVC-G3-
MICRO device is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.ubnt.com/compliance Eesti keel [Estonian] Kesolevaga deklareerib UBIQUITI NETWORKS, et kesolev raadioseadme tp antud UVC-G3-MICRO seade vastab direktiivi 2014/53/EL nuetele. ELi vastavusdeklaratsiooni tielik tekst on kttesaadav jrgmisel internetiaadressil:
www.ubnt.com/compliance Suomi [Finnish] UBIQUITI NETWORKS vakuuttaa, ett radiolaitetyyppi ett tm UVC-G3-MICRO laite on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen tysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.ubnt.com/compliance Franais [French] Le soussign, UBIQUITI NETWORKS, dclare que lquipement radiolectrique du type lappareil UVC-G3-MICRO est conforme la directive 2014/53/UE. Le texte complet de la dclaration UE de conformit est disponible ladresse internet suivante:
www.ubnt.com/compliance Deutsch [German] Hiermit erklrt UBIQUITI NETWORKS, dass der Funkanlagentyp dieses UVC-G3-MICRO Gert der Richtlinie 2014/53/EU entspricht. Der vollstndige Text der EU-
Konformittserklrung ist unter der folgenden Internetadresse verfgbar:
www.ubnt.com/compliance
[Greek] / UBIQUITI NETWORKS, UVC-G3-MICRO 2014/53/.
:
www.ubnt.com/compliance Magyar [Hungarian] UBIQUITI NETWORKS igazolja, hogy a UVC-G3-MICRO kszlk tpus rdiberendezs megfelel a 2014/53/EU irnyelvnek. Az EU-megfelelsgi nyilatkozat teljes szvege elrhet a kvetkez internetes cmen: www.ubnt.com/compliance slenska [Icelandic] Hr me lsir UBIQUITI NETWORKS yfir v a etta UVC-G3-MICRO tki er samrmi vi grunnkrfur og arar krfur, sem gerar eru tilskipun 2014/53/EU. Fullur texti ESB samrmisyfirlsing er a finna eftirfarandi netfangi: www.ubnt.com/compliance Italiano [Italian] Il fabbricante, UBIQUITI NETWORKS, dichiara che il tipo di apparecchiatura radio questo dispositivo UVC-G3-MICRO conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformit UE disponibile al seguente indirizzo Internet:
www.ubnt.com/compliance Latvi kalba [Latvian] Ar o UBIQUITI NETWORKS deklar, ka radioiekrta ka UVC-G3-MICRO ierce atbilst Direktvai 2014/53/ES. Pilns ES atbilstbas deklarcijas teksts ir pieejams d interneta vietn: www.ubnt.com/compliance Lietuvi kalba [Lithuanian] A, UBIQUITI NETWORKS, patvirtinu, kad radijo rengini tipas is UVC-G3-MICRO renginys atitinka Direktyv 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas iuo interneto adresu: www.ubnt.com/compliance Malti [Maltese] Bdan, UBIQUITI NETWORKS, niddikjara li dan it-tip ta tagmir tar-radju dan il-mezz UVC-G3-MICRO huwa konformi mad-Direttiva 2014/53/UE. Id-dikjarazzjoni tal-konformit tista tii kkonsultata minn www.ubnt.com/compliance Norsk [Norwegian] UBIQUITI NETWORKS erklrer herved at utstyret denne UVC-G3-MICRO enheten er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU-samsvarserklringen er tilgjengelig p flgende internettadresse:
www.ubnt.com/compliance Polski [Polish] UBIQUITI NETWORKS niniejszym owiadcza, e typ urzdzenia radiowego urzdzenie UVC-G3-MICRO jest zgodny z dyrektyw 2014/53/UE. Peny tekst deklaracji zgodnoci UE jest dostpny pod nastpujcym adresem internetowym:
www.ubnt.com/compliance Portugus [Portuguese] O(a) abaixo assinado(a) UBIQUITI NETWORKS declara que o presente tipo de equipamento de rdio este dispositivo UVC-G3-MICRO est em conformidade com a Diretiva 2014/53/UE. O texto integral da declarao de conformidade est disponvel no seguinte endereo de Internet: www.ubnt.com/compliance Romn [Romanian] Prin prezenta, UBIQUITI NETWORKS declar c tipul de echipamente radio acest dispozitiv UVC-G3-MICRO este n conformitate cu Directiva 2014/53/UE. Textul integral al declaraiei UE de conformitate este disponibil la urmtoarea adres internet:
www.ubnt.com/compliance Slovenina [Slovak] UBIQUITI NETWORKS tmto vyhlasuje, e rdiov zariadenie typu toto UVC-G3-MICRO zariadenie je v slade so smernicou 2014/53/E. pln E vyhlsenie o zhode je k dispozcii na tejto internetovej adrese: www.ubnt.com/compliance Slovenina [Slovenian] UBIQUITI NETWORKS potrjuje, da je tip radijske opreme ta naprava UVC-
G3-MICRO skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.ubnt.com/compliance Espaol [Spanish] Por la presente, UBIQUITI NETWORKS declara que el tipo de equipo radioelctrico este dispositivo UVC-G3-MICRO es conforme con la Directiva 2014/53/UE. El texto completo de la declaracin UE de conformidad est disponible en la direccin Internet siguiente:
www.ubnt.com/compliance Svenska [Swedish] Hrmed frskrar UBIQUITI NETWORKS att denna typ av radioutrustning denna UVC-G3-MICRO enhet verensstmmer med direktiv 2014/53/EU. Den fullstndiga texten till EU-frskran om verensstmmelse finns p fljande webbadress:
www.ubnt.com/compliance Online Resources Website www.ubnt.com Support help.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA 2017 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners. AIAJ070517
This product uses the FCC Data API but is not endorsed or certified by the FCC