FCC ID: SWX-UINS U-Installer

Installer Quick Start Guide Hardware Overview PoE OUT Port USB-C Port Removable Rubber Casing Wi-Fi LED Battery LEDs Front View Ports PoE OUT Supplies 24V passive PoE to the device being installed. USB-C recharging the internal battery. LEDs Wi-Fi Lights blue if the U Installer has a Wi-Fi connection to your mobile device. USB Type C port used for Battery internal batterys charge level:

Four blue LEDs indicate the Full charge Low charge*

* Recharge the battery by connecting a power source, such as mobile battery pack, to the USB-C port. Buttons Clip Removable Rubber Casing Back View Buttons Power Reset Ext Reset Reset Ext To reset the device connected to the U Installer to factory defaults, press this button while the device is powered on. Hold the button for more than 8 seconds until the LEDs on the device flash. [LED indication?]

Power on or off. [LED indication?]

Reset To reset the U Installer to factory defaults, press and hold the Reset button while the U Installer is powered on.

[LED indication?]

Press to power the U Installer Configure a CPE Device Use a mobile device to configure the CPE device at the point of installation via the U Installers Wi-Fi:

1. Power on the U Installer by pressing the Power button. The [Wi-Fi? LED will light blue?] when the power is on. 2. If the battery level is low, connect a USB cable from a mobile power pack or computer to the USB-C port of the U Installer. 3. Connect an Ethernet cable to the PoEOUT port on the U Installer. 4. Connect the other end of the cable to the CPE device. You have two options for configuration:

the U Mobile App and Web Portal. Proceed to the appropriate instructions:

U Mobile App 1. Launch the U Mobile app on your mobile device. Note: If the app is not yet installed on your mobile device, download it from AppStore (iOS) or Google Play (Android). 2. Follow the on-screen instructions to configure the connected device. Web Portal 1. Connect your mobile devices Wi-Fi to the U Installer SSID named:

U Installer:<MAC Address>. 2. Open a web browser on your mobile device and go to https://192.168.1.20 3. The login portal of the CPE device will appear. 4. Log in and configure theCPE device as needed. Example Login Screen for CPE Device Removing the U Installer After you have configured the CPE device, remove the U Installer:

1. Disconnect the Ethernet cable from the device. 2. Connect the Ethernet cable from a PoE adapter or switch to the device. Safety Notices 3. Read, follow, and keep these instructions. 4. Heed all warnings. 5. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturers label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. 4. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-

circuit backup protection. 5. Protective bonding must be installed in accordance with local national wiring rules and regulations. Limited Warranty UBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) warrants that the product(s) furnished hereunder (the Product(s)) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty Conditions The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks authorized representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;

(V) has been damaged or impaired as a result of using third party firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed. Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty. Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYERS EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-

free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyers selection of products (including the Products) for buyers application and/or failure of products (including the Products) to meet government or regulatory requirements. Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE

(EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products.

*640-00289-01*

640-00289-01 Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This radio transmitter FCC ID: SWX-UINS has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna Information: 2.4 GHz PIFA antenna, Gain: 1 dBi 5 GHz PIFA antenna, Gain: 2 dBi Industry Canada CAN ICES-3(B)/NMB-3(B) To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the band 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.This radio transmitter (IC: 6545A-UINS) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna Information: 2.4 GHz PIFA antenna, Gain: 1 dBi 5 GHz PIFA antenna, Gain: 2 dBi CAN ICES-3(B)/NMB-3(B) Pour rduire le risque dinterfrence aux autres utilisateurs, le type dantenne et son gain doivent tre choisies de faon que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est ncessaire pour une communication russie. Cet appareil est conforme la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes:

1. Cet appareil ne peut pas provoquer dinterfrences et 2. Cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement du dispositif. Les utilisateurs devraient galement noter que radars haute puissants sont allous comme principaux utilisateurs (cest-

-dire les utilisateurs de priorit) des bandes et 5650 5850 MHz et que ces radars pourraient causer des interfrences ou dommages aux dispositifs LAN. Cet metteur radio (IC:

6545A-UINS) a t approuve par Industrie Canada pour lexploitation avec lantenne types numrs ci-dessous avec le gain maximal admissible et requis limpdance de lantenne pour chaque type dantenne indiqu. Types dantenne non inclus dans cette liste, ayant un gain suprieur au gain maximal indiqu pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Informations dantenne: 2.4 GHz PIFA antenne, Gain: 1 dBi 5 GHz PIFA antenne, Gain: 2 dBi RF Exposure Warning This device has been tested and meets applicable limits for radio frequency (RF) exposure. This device was tested with separation distance of 0 mm un-

der body-worn accessory (holster) operation condition. Al-

ways carry this device within a holster, to ensure exposure levels remain at or below the as-tested levels Cet appareil a t test et respecte les limites applicables l'exposition aux frquences radio (RF). Cet appareil a t test avec une distance de sparation de 0 mm sous l'tat de fonctionnement des accessoires (tui) us par le corps. Portez toujours cet appareil l'intrieur d'un tui pour vous assurer que les niveaux d'exposition restent au niveau ou sous les niveaux tests Australia and New Zealand Warning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Deutsch Die Europische Richtlinie 2012/19/EU verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Espaol La Directiva 2012/19/UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto. Franais La directive europenne 2012/19/UE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italiano La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity esky

[Czech]

UBIQUITI NETWORKS tmto prohlauje, e toto UBIQUITI NETWORKS zazen, je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Hermed, UBIQUITI NETWORKS, erklrer at denne UBIQUITI NETWORKS enhed, er i overensstemmelse med de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hierbij verklaart UBIQUITI NETWORKS, dat deze UBIQUITI NETWORKS apparaat, in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI NETWORKS device, is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Kesolevaga UBIQUITI NETWORKS kinnitab, et antud UBIQUITI NETWORKS seade, on vastavus olulistele nuetele ja teistele asjakohastele stetele direktiivi 1999/5/E. Tten UBIQUITI NETWORKS vakuuttaa, ett tm UBIQUITI NETWORKS laite, on yhdenmukainen olennaisten vaatimusten ja muiden sit koskevien direktiivin 1999/5/EY. Par la prsente UBIQUITI NETWORKS dclare que lappareil UBIQUITI NETWORKS, est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Dansk

[Danish]

Nederlands

[Dutch]

English Eesti

[Estonian]

Suomi

[Finnish]

Franais

[French]

Deutsch

[German]

[Greek]

Magyar

[Hungarian]

slenska

[Icelandic]

Italiano

[Italian]

Latviski

[Latvian]

Lietuvikai

[Lithuanian]

Malti

[Maltese]

Hiermit erklrt UBIQUITI NETWORKS, dass sich dieses UBIQUITI NETWORKS Gert, in bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet.

, UBIQUITI NETWORKS, UBIQUITI NETWORKS, 1995/5/. Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a UBIQUITI NETWORKS kszlk megfelel az alapvet kvetelmnyeknek s ms vonatkoz 1999/5/EK irnyelv rendelkezseit. Hr, UBIQUITI NETWORKS, v yfir a etta UBIQUITI NETWORKS tki er samrmi vi grunnkrfur og nnur vieigandi kvi tilskipun 1999/5/EB. Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo UBIQUITI NETWORKS, conforme ai requisiti essenziali ed alle altre disposizioni pertinenti della direttiva 1999/5/CE. Ar o, UBIQUITI NETWORKS, deklar, ka UBIQUITI NETWORKS ierce, ir saska ar btiskajm prasbm un citiem attiecgiem noteikumiem Direktv 1999/5/EK. UBIQUITI NETWORKS deklaruoja, kad is UBIQUITI NETWORKS renginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz UBIQUITI NETWORKS huwa konformi mar-

rekwiiti essenzjali u dispoizzjonijiet rilevanti orajn ta Direttiva 1999/5/KE. Norsk

[Norwegian]

Polski

[Polish]

Portugus

[Portuguese]

Romn

[Romanian]

Slovensky

[Slovak]

Espaol

[Spanish]

Svenska

[Swedish]

Herved UBIQUITI NETWORKS, erklrer at denne UBIQUITI NETWORKS enheten, er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktiv 1999/5/EF. Niniejszym, Ubiquiti Networks, owiadcza, e urzdzenie UBIQUITI NETWORKS, jest zgodny z zasadniczymi wymaganiami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/WE. UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Prin prezenta, UBIQUITI NETWORKS declar c acest dispozitiv UBIQUITI NETWORKS este n conformitate cu cerinele eseniale i alte prevederi relevante ale Directivei 1999/5/CE. Tmto UBIQUITI NETWORKS, prehlasuje, e toto UBIQUITI NETWORKS zariadenie, je v slade so zkladnmi poiadavkami a almi relevantnmi ustanoveniami smernice 1999/5/ES. Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Hrmed UBIQUITI NETWORKS, intygar att denna UBIQUITI NETWORKS enhet r i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Online Resources Support support.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com w w w . u b n t . c o m 2017 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the UbiquitiU logo, the Ubiquiti beam logo, airMAX, airOS, and U Installer are trademarks or registered trademarks of UbiquitiNetworks,Inc. in the United States and in other countries. All other trademarks are the property of their respectiveowners. AI031617