FCC ID: 2ADG4J-SP Wireless camera monitor system (transmitter)

Structure and Denitions Technical Parameters Model NO.SP-536A+DF-8275HA-SFS-CUT Side View 70.5 PAIR instruction PAIRING SART 20 PAIR: Establish the connection between the monitor and camera, make the system work in order. Enter the menu, chose PAIR and press OK to enter the pair. the monitor display PAIRING START 20. During the 50 seconds, make the camera re-energized, the monitor will show the camera image in 5~10s. Front View Rear view Support drawing 36 82 35 5 7 106 91 Power Input Camera Image Pick-up Device Power(Red) Ground(Black) DC Input: 8-32V AC M1 Power(Red) Ground(Black) DC Input: 11-32V Color CMOS Camera 1/3" Color CMOS Picture Elements NTSC:960(H)X480(V);PAL:960(H)X480(V) Horizontal Resolution Transmission Power 600 TV Lines 8dBm-10dBm with Power control Minimum illumination 0 Lux At Night ( IR LED ON) Automatic switch, day and night mode IR-CUT View Angle Waterproof rating Shockproof R ating 120 IP69K 10G Fleet &

Heavy truck Fork Lift Trailer & RV AG Equipment Construction machinery vehicles operating voltage range DC11~32V Dimension 106(W) x 75(H) x 70.5(D) mm FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving an Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the tenna. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Label Location On EUT Label

(transmitter) Product Name: Wireless camera monitor system Model No.: SP-536A+DF-8275HA-SFS-CUT FCC ID: 2ADG4-SP This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Veise (GuangZhou) Electronics Co., Ltd. Declaration concerning Antenna Specification It is hereby declared that the product Model No.:SP-536A+DF-8275HA-SFS-CUT, SP-536H+DF-8275H-SFS-CUT, SP-723H+DF-

8275H-SFS-CUT, SP-723H4+DF-8275H-SFS-CUT, SP-766H+DF-8275H-SFS-CUT, SP-

766H4+DF-8275H-SFS-CUT, SP-755H+DF-8275H-SFS-CUT, SP-755H4+DF-8275H-SFS-CUT, SP-966H+DF-8275H-SFS-CUT, SP-966H4+DF-8275H-SFS-CUT, MWHD-772S+CWHD-161M FCC ID :2ADG4-SP fulfills the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for External antenna type(s) described below:

2.4G:

Model No. of antenna: N/A Type of antenna:

Columnar Antenna Gain of the antenna: 5 dBi Frequency range:

2406~2472.5MHz The mounting of the antenna is fixed to the radio module and no other antenna should be used. Company name: Veise (GuangZhou) Electronics Co., Ltd. Address: 3-4F, No.18th, Huayuan St., Shatai Rd., Baiyun District, Guangzhou China City:

ZIP / Postal code: N/A Country:

Guangzhou China Place:

Date: 2021-02-03 Guangzhou China Signature:

version01