FCC ID: OYQWSMS0272B00001 RF Mouse

FCC Information The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph:

The equipment has been tested and found comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause-harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

* Reorient or relocate the device antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet ona circuit different from that to which the receiver is connected,

* Consult the dealer or an experienced tadio/TV technician for help. The user should not modify or change this equipment without written approval from Wen Shing Electronics Co., Ltd. Modification could void authority to use this equipment. Users manual Important Ergonomic Information Some research suggests, after long period of repetitive motions of using an improperly set up workplace, incorrect body position or bad habits, can result in physical discomfort, even injury to nerves, tendons and muscles. To reduce the risk of injury, try the following:

Take frequent breaks. Vary your work, do something different with your arms and hands. Adjust to comfortable position Use light touch keyboard or better controlled mouse If you feel pain, numb, weak,or any discomfort with your wrist,arms,shoulders,neck or back while using a keyboard or mouse we advis you to see a qualified health professional. INDEX I Appearance Il Installations 2-1 Installation of batteries 2-2 Connecting the receiver Ill LED Display Indications IV. Use Alternative Channels V_ Trouble Shooting 5-1 Mouse Dose Not Work After Installation 5-2 Mouse Not Detected 5-3 The Cursor Dose Not Move On The Screen VI Maintenance I Appearance

\a

Receiver and PS/2 cable connector

Il Installations

* Before you install your FUZZY MOUSE please remove all mouse drivers provided by other software/hardware company, it might beincompatible with FUZZY MOUSE. 2-1 installation of batteries FUZZY MOUSE uses 2 standard AAA batteries. For optima performance, please use alkaline batteries. To install the batteries:

1. Remove the battery compartment cover. Remove the cover bypressingthetab | 4 at the bottom of the mouse. 2. Slide the cover away backwards to remove it. 3. Insert two AAA batteries. Please see the diagram in the battery compartment for correct installation. 4. After the batteries are properly installed, carefully replace the cover back and press the tab again to lock the cover. 2-2 Connecting the receiver ~~~

The receiver is connected to your computer with a single cable to the PS/2 port. 1.Before connecting the receiver,please make sure your computer is properly turned off. Plugging and unplugging the cables to your computer without properly turned off your computer may cause damage to your PS/2 port. FUZZY MOUSE dose not require any additional software. After you have correctly installed the mouse itis ready for use.

@: - Fantintee Ill LED Display Indications Our Fuzzy Mouse comes with a friendly design that let you keep track of your mouse's performance. This feature enables you to know exact status of your mouse. ALED installed on the receiver help users to track the various status of the mouse. LED Status | Indications The LED is}Normal. | The mouse is shining communicating with the when the computer and trying to computer establish communication. is turned on. The LEDis|Disconnected | 1.Unable to establish shining _|* To solve it connection with the during use.|please refer computer. to 2.Unable communicate troubleshooting.| with the computer. 3.Disconnected from the receiver. The LED is|Mouse in When the mouse has off. use established the connection the LED will extinguishit self. The LED is|Channel fleshing. |searching When you are tuning for another channel the LED will be fleshing. After the receiver have reestablished the connection with the mouse, the LED will extinguish it self. IV Use alternative channels Some time you may need to change channels to avoid jamming with other devices or for betterreception.Please follow the instruction below. 1. Press the channel button on the receiver till you see the LED fleshing. 2.Press the channel button under the mouse for 2seconds

3 .Move the mouse or click any. button on the mouse

, the receiver will automatically switch to the other channel. There are 16 channels to choose from. Le Note: When there are two or more mouses ina room set them up one by one . Do not set all mouses at once because it might cause interference with other mouse. VY Troubleshooting 5-1 Mouse dose not work after installation If ever occur, please try one or more of the following measure to resolve the problem. 1. Make sure you have connected the receiver firmly to the tight port (PS/2). 2. Make sure the batteries correctly placed and in working condition, if it's not please replace the batteries. 3, Use a mouse pad. Especially when you are working ona metallic surface. 4. Change the channel that you are using. (please refer to use alternative channel ) 5. Remove previous mouse drivers. 5-2 Mouse Not detected If the mouse is not detected please try the following to solve the problem:

1. Make sure the receiver cable is plugged into the right PS/2 port. But do not plug and unplug the cable without turning your computer off. 2. Make sure your serial port (PS/2) has the correct configuration. (Please refer to your computer documents)