FCC ID: 2A2JCEQBSU-U00 Whipr Base Unit

®

Paddle. Ski. Row +

THE WORLD'S ONLY PORTABLE MULTI-SPORT ERG MACHINE

Whipr Base Unit

Model: EQBSU-U00-BL1 or EQBSU-U00-BK1

Instruction Manual

Includes: Base Unit, Stabilizing Bracket (for door), Strap Anchor, Ground Anchor, Webbing

Strap, Carry Bag(Needs 3 AA Batteries - Not Included)

1)Install 3 AAA batteries. Batteries are located in the bottom of the unit. They can be installed by snapping off

the plastic cover by pulling on both sides.

2)Turn power on by pushing and holding button on the far left (the one with the circle and vertical line in it).

3)After turning power on, you will need to select the desired sport mode. To select the mode, you will press the

2nd button on the left (the one with the 3 horizontal lines). You will then press the button in the middle (the one

with the circle). The modes will be highlighted on the right. You will push the up or down button to select the

desired mode. The options are: ROW, KAYAK, SWIM, OPEN, SUP, SKI. After selecting the mode, press the

2nd button again (the one with the 3 horizontal lines).

4)Resistance Mode – should now be selected from the wheel located at the back of the unit (1-10…1 being the

easiest and 10 being the most difficult).

5)You are now ready to begin your exercise.

6)You can reset your workout any time by pressing the middle button (the one with the circle in it).

The Display Stats include the following:

Strokes/Minute, Distance, Time, 500 Meter Split Time, Projected Time, Calories, Average Watts

Securing the Unit – some modalities require the Base Unit to be secured. There are 3 ways to secure the unit.

Door - Securing the unit by using the attached inflatable anchor that goes under a door. The door should be a

standard 3.5cm width door with up to a 2cm gap.

1)Stabilizing Bracket needs to be attached to the base unit – this easily can be done by locking the tabs on the

bracket into 2 slots located on the bottom corners of Base Unit.

2)Slide the Bracket and Inflatable rubber anchor under the door.

3)Inflate the rubber anchor by pushing the larger of the 2 rubber balls on the Base Unit. You will need to keep

pushing it until the anchor and bracket are fully secure and very tight under the door.

When you are finished and would like to remove the Base Unit from the door crack, you can push the smaller

rubber ball and the anchor will deflate. After removing from under the door, the Bracket can be taken off easily

by pulling gently and removing from the grooves on the Base Unit.

Strap Anchor – The strap holder can rotate to be horizontal or vertical

1)Before attaching the strap anchor, make sure the plastic panel that the bladder folds into is securely attached

to the base unit. Also make sure the bladder is evenly placed in the square box (connects by magnets located

within the top of the bladder).

2)The lug bolts on the strap anchor easily locks into place on the back of the Base Unit.

3)Take the loop end of the strap and place through anchor hole.

4)Wrap around object.

5)Place buckle through loop and tighten..

Ground Anchor – To use ground anchor, put in ground and wrap strap around anchor.

See video links also: https://www.youtube.com/watch?v=7fCmaVLTanY

https://whipr.com/collections/whipr-ecosystem/products/whipr-base-unit

FCC DISCLAIMER

Changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Canada IC DISCLAIMER

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the

device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

3. For WIFI product, it should be added:

This equipment complies with FCC’s and IC’s RF radiation exposure limits set forth for an uncontrolled

environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation

distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other

antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the

device (excluding its handset) and users.

Cet appareil est conforme aux limites d’exposition au rayonnement RF stipulées par la FCC et l’IC pour une

utilisation dans un environnement non contrôlé. Les antennes utilisées pour cet émetteur doivent être installées

et doivent fonctionner à au moins 20 cm de distance des utilisateurs et ne doivent pas être placées près d’autres

antennes ou émetteurs ou fonctionner avec ceux-ci. Les installateurs doivent s’assurer qu’une distance de 20 cm

sépare l’appareil (à l’exception du combiné) des utilisateurs.

RED DISCLAIMER

EU Declaration of Conformity

We,

WHIPR, INC.

251 Little Falls Drive, Wilmington, Delaware, 19808, USA

Declare that the DoC is issued under our sole responsibility and belongs to the following product(s):

Product Type:

Whipr Base Unit

Model Number(s): EQBSU-U00-BL1, EQBSU-U00-BK1

Software Version: 11.03

Accessories: N/A

The object of the declaration described above is in conformity with the essential requirements of the

relevant Union harmonization legislation:

Radio Equipment Directive 2014/53/EU

The following harmonized standards and technical specifications have been applied:

Health and Safety (Article 3.1a):

EN 62479:2010

EN IEC 62311:2020

ETSI EN 301 489-1 V2.2.3 (2019-11)

ETSI EN 301 489-17 V3.2.4 (2020-09)

EN 55014-1:2017+A11:2020

EN IEC 61000-3-2:2019

EN 61000-3-3:2013+A1:2019

EN 55014-2:2015

Radio Spectrum (Article 3.2):

ETSI EN 300 328 V2.2.2 (2019-07)

Notified Body Involved: N/A

Technical Compliance File Held by:

WHIPR, INC.

251 Little Falls Drive, Wilmington, Delaware, 19808, USA

Signed for and on behalf of WHIPR, INC.

Name and Title:

Adrina Lee, Director of Global Supply Chain

Address:

251 Little Falls Drive, Wilmington, Delaware, 19808, USA

Wilmington, Delaware 7/22/21

Place of issue

Date of issue

Signature of Authorized Person

UKCA Declaration of Conformity

We,

WHIPR, INC.

251 Little Falls Drive, Wilmington, Delaware, 19808, USA

Declare that the DoC is issued under our sole responsibility and belongs to the following product(s):

Product Type:

Whipr Base Unit

Model Number(s): EQBSU-U00-BL1, EQBSU-U00-BK1

Software Version: 11.03

Accessories: N/A

The object of the declaration described above is in conformity with the essential requirements of the

relevant Union harmonization legislation:

Radio Equipment Directive Radio Equipment Regulations 2017

The following harmonized standards and technical specifications have been applied:

Health and Safety (CHAPTER

1 6(1)(a)):

EN 62479:2010

EN IEC 62311:2020

EMC (6(1)(b)):

ETSI EN 301 489-1 V2.2.3 (2019-11)

ETSI EN 301 489-17 V3.2.4 (2020-09)

EN 55014-1:2017+A11:2020

EN IEC 61000-3-2:2019

EN 61000-3-3:2013+A1:2019

EN 55014-2:2015

Notified Body Involved: N/A

Technical Compliance File Held by:

WHIPR, INC.

251 Little Falls Drive, Wilmington, Delaware, 19808, USA

Signed for and on behalf of WHIPR, INC.

Name and Title:

Adrina Lee, Director of Global Supply Chain

Address:

251 Little Falls Drive, Wilmington, Delaware, 19808, USA

Wilmington, Delaware 7/22/21

Place of issue

Date of issue

Signature of Authorized Person

WIFI

(a) Transmitting frequency band(s):2412 MHz-2472 MHz

(b) Maximum allowed transmitting power in the frequency band(s) in which the radio equipment

Operates: E.I.R.P.: <20 dBm

Bluetooth

(a) Transmitting frequency band(s): 2402 MHz–2480MHz

(b) Maximum allowed transmitting power in the frequency band(s) in which the radio equipment

Operates: E.I.R.P.: <8 dBm

EMC (Article 3.1b):

Radio Spectrum (6(2)):

ETSI EN 300 328 V2.2.2 (2019-07)

Size：66X53 mm

Material：silver polyster

Affix location：The bottom of the base unit

base unit

LABEL AREA

Whipr Inc. July 12, 2021 Attention: Application Examiner RE: Request for Confidentiality Applicant: Whipr Inc. FCC ID: 2A2JCEQBSU-U00 To Whom It May Concern:

Permanent Confidentiality [Complete this section if permanent confidentiality is requested]

Request is hereby submitted by Whipr Inc. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

[Select one or more of items below, as appropriate]

e Schematics e Detailed Block Diagrams e Detailed Operational/Functional Description Rationale for request for confidentiality:

Whipr Inc. has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.]

If you have questions or need further information, please contact the undersigned. Sincerely, Adrian Lee Director of Global Supply Chain Whipr Inc. 1(1)

Whipr Inc. July 12, 2021 Federal Communications Commission 445 12" Street SW Washington, DC 20554 Subject: Limited Agency Agreement Whipr Inc. FCC ID: 2A2JCEQBSU-U00 To Whom It May Concern:

We, Whipr Inc., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number (2A2JCEQBSU-U00) under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is July 8, 2021. The Limited Agency Agreement expires on Jan. 7, 2022, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Adrian Lee Director of Global Supply Chain Whipr Inc.