FCC ID: 2AUIUWYZELS1 WYZELS1

WYZELS1-KSZP01 V1.0 105g IN THE BOX GET STARTED If you are installing Wyze Lamp Socket for the first time, please follow the next steps to install it. If you have already installed a Wyze Lamp Socket at this location, you can repeat steps 3, 4, and 6 to install the expansion. 1 Download the Wyze app and sign in or create an account. Wyze Lamp Socket USB Cable*

Wall Anchors 6 Screws 6 USB Cable Clips 6 This is an expansion kit. You need to have a starter bundle or install a Wyze Cam v3 together with this lamp socket to be able to control this socket from the Wyze app. 2 Check WiFi Signal Strength Connect your phone to your 2.4 GHz network. Do not use your phone's data connection. Move your phone to where you'll install the Wyze Cam v3 to check your WiFi's signal strength. 3 Before going further, cut the power to your lamp socket and unscrew the existing light bulb. 4 Screw the light bulb into the E26 base of the lamp socket. Note: Only bulbs with < 30 W can be used. 6 Screw your Wyze Lamp Socket into the E26 base and position your USB cable. If you want to use tape, please remove the protective film at the back of the clip and press it firmly to the wall. Wait for 10 minutes before putting the cable inside the clip. 8 Connect the USB cable to the your Wyze Cam v3. Make sure it is connected securely. 5 Open the dust cover and plug in the USB cable. Note: Please use the USB cable included in this package. Do NOT use original Wyze Cam v3 cable. 7 Plan the route to run the USB cable to the place you want to position the your Wyze Cam v3. You can use USB cable clips to route your USB cable. You can use tape or screws to secure the clips. If you want to anchor the cable clips using screws, please first drill a hole on the wall using 4.0 drill bit. Then insert and insert the anchor into the hole. Screw the clip onto the wall. 9 Place the USB cable in the USB cable clip. 10 After connecting the wires, restore power to the lamp socket. The light bulb will turn on and your Wyze Cam's status light will flash red. 11 Stick the sticker next to the switch to avoid switching the light off accidentally. 12 Installation complete! You can now control your new lamp socket with your Wyze Cam v3. DEVICE NETWORKING 1 Lamp sockets that you want to group together should be within 82 feet of the socket with the camera. Primary Socket Secondary Socket MAX 82 feet MAX 82 feet When Wyze Cam v3 is connected to a Wyze Lamp Socket, it can control up to 4 nearby Wyze Lamp Sockets within 82 feet. 2 3 If installing multiple Wyze Lamp Sockets, turn them on within 30 seconds of each other to group them together. Use the Wyze app to manage your lamp socket's settings. BASIC OPERATION Setup In the Wyze app, open your Wyze Cam v3. If installed properly, your Wyze Lamp Socket will be automatically added as an accessory. Secondary lamp sockets must be installed within 82 feet of the primary lamp socket to be grouped together. In your Wyze Cam v3 Settings, open Accessories > Lamp Socket to adjust your lamp socket settings. Daily use Daily use the AUTO | On | Off functions in the Wyze app to control when the lamp socket turns on and off. Each grouped lamp socket will update with your changes. AUTO: Select Always for the lamp socket to turn on automatically when it is dark. Select Motion is detected by camera for it to turn on when the camera detects movement in low ambient light. On: Turns the lamp socket on. Off: Turns the lamp socket off. BASIC SPECIFICATIONS Lamp socket base type: E26 Lamp socket input voltage: 120V~, 60Hz USB output voltage: DC 5V/1A MAX 5W USB1.1 Lamp socket output voltage: 120V~, 60Hz Maximum Power: 30 W Wireless: 2.4 GHz Operating temperature: -4~120(-20C~50C) ATTENTION:

Before installing, turn off the power to the light fixture. Do not touch the metal components of the lamp. Make sure your lamp socket output is 120V. This product is not waterproof and must be used with an enclosure. FOR BOTH FCC & IC APPLICATION:

This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. MPE Requirements To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installes doivent tre situes de facon ce que la population ne puisse y tre expose une distance de moin de 20 cm. Installer les antennes de facon ce que le personnel ne puisse approcher 20 cm ou moins de la position centrale de l antenne. La FCC des ltats-unis stipule que cet appareil doit tre en tout temps loign dau moins 20 cm des personnes pendant son functionne-

ment. Region Selection Limited by local law regulations, version for North America does not have region selection option. NEED HELP?

Contact our Support Team:

https://wyze.com/support Join our Community:

https://wyze.com/community User Manual Version: V1.0 Scan the QR code to learn more Wyze Lamp Socket 55*55mm 2021.4.22 V1.0 2021.4.25 V1.0 1 2021.4.25 V1.0 2021.6.7 V1.0 WYZELS1 WYZELS1-

KSZP01 V1.0

7 \Nyze Lamp Socket \

Lamp socket base type: E26 Lamp socket Input voltage: 120V~60Hz USB output voltage:DC5V/1A, MAX 5W, USB1.1 Lamp socket output voltage: 120V~, 6042,

be

FCC ID: 2AUIUWYZELS1 WYZE LABS.Inc. IC: 25466-WYZELS1 _Deslgned In Seattle MAC: XXXXXXXK Made In China

Wyze Labs, Inc. Wyze Labs. Inc. 3933 Lake Washington Blvd NE, Suite 350 Kirkland, WA 98033 Authority to Act as Agent Date: November 3, 2021 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

______Intertek Testing Services Shanghai______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: _____Dec 30, 2021_____ By:

(Signature1) _____ Steve Skeoch __________

(Print name) Title:

_____Head of Hardware________ On behalf of: ___ Wyze Labs, Inc __

(Company Name) Telephone:

___8582185969__________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Wyze Labs, Inc. Wyze Labs. Inc. 3933 Lake Washington Blvd NE, Suite 350 Kirkland, WA 98033 Request for Confidentiality Date: November 3, 2021 Subject: Confidentiality Request for: ______( FCC ID: 2AUIUWYZELS1, IC ID:25466-WYZELS1)______ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent *1 Permanent Permanent Permanent Permanent Permanent *3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Wyze Labs, Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180)2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

(Signature/Title3) ____ Steve Skeoch ________

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.