Before beginning assembly, please read these instructions thoroughly!
Lap Time Detector Instruction Manual No.ZRW-05-R/ C About This Device K Y O S H O LapT im eD etector P C IC R / C Thank you for purchasing the KYOSHO Lap Time Detector. When connected to a personal computer installed with special software, this device works as a lap count antenna for mini R/C cars fitted with an IC tag. Please read these instructions carefully and keep them for future reference. Safety Precautions Please read carefully before assembling and operating your model
. WARNING!
: This symbol indicates where caution is essential to avoid injury to yourself or others. PROHIBITED
:This symbol points out actions that you should NOT do to avoid possible damage or accidents. Always keep this instruction manual ready at hand for quisk reference. 14 This model is not a toy. It is designed for users over 14 years of age.
*Specifications are subject to change without prior notice!
32011-T01 1 Copyright 2008 KYOSHO CORPORATIO N This product emits electrical waves so do not operate:
Inside an aircraft. Near automatic devices such as automatic doors and re alarms. Inside hospitals or medical equipment. Operating may cause accidents. Only use genuine Kyosho parts and do not modify the model. Using other parts or making modications may cause damage. Do not store this model in a high-temperature/humidity area or in direct sunlight. This product use spohisticated electronic components. Do not allow them to get wet as this can cause damage. Avoid drops or servers shocks to this product. Hereby, KYOSHO CORPORATION, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC . The Declaration of Conformity (DoC) can be downloaded at following URL. www.kyosho.com/eng/support/doc/index.html This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the manufacturer for compliance could void the user's authority to operate the equipment. 2 Item Included Lap Time Detector U S B (1.5m) USB Cable (1.5m) Glossary of Main Parts LE D LED indicates lap detection (Green) Antenna Section LE D LED indicates power status (Red) U S B USB port Connectin g Disconnect Device may not be recognized if it is connected or disconnected while the software program is running. In this case restart the program or the computer. For detailed operating instructions, please refer to the user manual for the software program. Connecting U S B miniBU S B AP C U S B Insert miniB (narrow end) to the USB port on the lap count antenna, and then insert A (wide end) into the USB port on the computer. U S B When USB cable is inserted, the computer may indicate that a software driver is required to be installed. In this case, refer to the instruction manual for the software program and follow the instructions accordingly. miniB A Disconnect After quitting the software program, disconnect both ends of the USB cable. 3 Antenna Setup Caution 20cm Setup the antenna in a place at least 20cm clear of any metal. To ensure stable reception of the antenna, set the antenna up at slow sections of the race course (chicanes and after hairpin turns). 970m m 970m m The length of the antenna section is 970mm. It cannot be setup on a course wider than this. Setup the antenna section where the width is less than 970mm. When using with carpet race courses, set the antenna section underneath the carpet. When using with urethane race courses, the antenna can be set on the top or underneath the surface. CAUTION: If running on thick carpet or urethane, the antenna reception can be affected if the antenna section is underneath the racing surface. Try to position the antenna section as close as possible to the top of the racing surface. Specications D C 5.0VU S B Power Supply: DC5.0V (USB power) 120AR F O N Power Consumption: 120mA (when RF is ON) U S B 2.0U S B 1.1U S B 2.0 Compatible Interface: USB 2.0 and USB 1.1 (USB 2.0 recommended) 13.56M H z Frequency: 13.56MHz Dimensions 58m m 18m m 95m m Case (W x H X D): 58mm x 18mm x 95m m 1.2 Length" 1.2m (approx.) 260gU S B Weight: 260g (without USB cable) Specified Operating Conditions 106010R H 80R H Temperature: -10+60, Humidity 10%RH80%RH (without condensation) R /C www.kyosho.com d N a N o www.dnano.jp 4 243-0034 153 046-229-4115
()1000 18 00 61920807-1 PRINTED IN JAPAN