MF971V LTE Ufi User Manual

 

MF971V Quick Start Guide Getting to Know Your Device Appearance The following figure is for your reference only. 1. Power key 2. FUNC key 3. External antenna connector 4. LCD screen 5. External antenna connector 6. Charging/micro-USB jack 7. micro-SIM card slot and reset hole 2 Getting to Know Your Device Indicators When the device is powered on, the following icons may be displayed on the LCD screen. For a de-

scription of the icons, refer to the following table. Icon Description Network signal strength 4G/3G/2G Network type The user is in roaming status. Connected to the Internet. Connected to the Internet in the Internet Wi-Fi mode. New message(s) Wi-Fi status and the number of connected users Battery level 3 Getting to Know Your Device Connection Scenarios The device allows multiple clients to surf on the Internet at the same time. The following figures are for your reference only. A micro-SIM card can be used to access the Internet. 4 Installing the micro-SIM Card 1. Open the micro-SIM card slot cover, and install a micro-SIM card to the micro-SIM card slot. NOTE:

Do not remove the cover rudely, because it is con-

nected with the device. WARNING!

To avoid damage to the device, do not use any oth-

er kind of SIM cards, or any non-standard micro-

SIM card cut from a SIM card. You can get a stan-

dard micro-SIM card from your service provider. 2. Close the micro-SIM card slot cover. 5 Connecting to Your Device Using Wi-Fi 1. Power on your device. 2. Ensure that your computer or other client de-

vices have enabled Wi-Fi, and search for avail-

able wireless networks. NOTE:

Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless net-

works. If you use a computer, you need to set your computer to obtain an IP address automatically. 3. Select the Wi-Fi name (SSID) of your device, and click Connect. 4. Enter the Wi-Fi password if necessary, and click OK. NOTE:

Refer to the chapter Getting to Know the Wi-Fi SSID and Password to get the default Wi-Fi SSID and password. 5. Wait until the client device is connected to your device successfully. 6 Connecting to Your Device Using a USB Cable 1. Connect a computer to your device with a USB cable. 2. Power on your device. The operating system detects and identifies new hardware, and auto-

matically installs the software. NOTE:

If the system does not automatically launch instal-

lation, you can Double-click the device installation icon in My Computer to install the software. 3. Wait until the computer is connected to your device successfully. 7 Getting to Know the Wi-Fi SSID and Password You can use the following methods to get the de-

fault Wi-Fi SSID and password. View the label on the device. Press the FUNC key to access the options menu. Select Device Info and the Wi-Fi SSID and password are displayed on the screen. Logging in to the 4G Mobile Hotspot Configuration Page 1. Ensure that the connection between your de-

vice and the client device is correct. 2. Launch the Internet browser and enter http://192.168.0.1 or http://ufi.ztedevice.com in the address bar. 3. Enter the password to log in to the 4G Mobile Hotspot configuration page. NOTE:

The default password is admin. 8 Changing the Wi-Fi SSID or Password 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Settings below Wi-Fi and then click Main SSID. 3. Change the Network Name (SSID) or the Password in the Main SSID area. 4. Click Apply. Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Auto-

matic or Manual mode. The default mode is Auto-

matic. Mode Operation Automatic Your device is automatically connect-

ed to the Internet, and you can surf on the Internet through the client. 9 Accessing the Internet Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Settings > Connection Mode > Manual, and then click Apply. 3. Click to back to the home or page, and click

. You can also press the FUNC key and select Network Connec-

tion. Select Yes or No. NOTE:

To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page. 10 Using the FUNC Key When the screen is off:

When the screen is on:

Press the FUNC key to turn on the screen. Press the FUNC key to access the options menu. You can connect or disconnect with the Internet, view device information or Wi-Fi QR code, activate WPS function, enable/disable global roaming or quick boot function without logging in to the 4G Mobile Hotspot Configura-

tion Page. 11 Configuring Your PC The following describes how to configure the Inter-

net Protocol in the Windows 7 for your Wi-Fi con-

nection. 1. Right-click Network and select Properties. 2. Select Change adapter settings. 3. Right-click Wireless Network Connection and select Properties. 4. Select Internet Protocol Version 4 (TCP/

IPv4), and click Properties. 5. Select Obtain an IP address automatically and Obtain DNS server address automati-

cally, and click OK. 12 Warning and Notice To the Owner If inadequately shielded, some electronic de-

vices, for example, the electronic system of ve-

hicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary. Operating the device may interfere with medi-

cal instruments such as hearing aids and pace-

makers. Always keep the device more than 20 centimeters away from such medical instru-

ments when your device is powered on. Power off the device if necessary. Consult a physician or the manufacturers of medical instruments before using the device if necessary. Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary. 13 Warning and Notice Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Ob-

serve and obey all warning signs, and power off the device in these conditions. Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be affected. Do not use the device in an enclosed environ-

ment or where heat dissipation is poor. Pro-

longed work in such space may cause exces-

sive heat and raise ambient temperature, which may lead to automatic shutdown of the device for your safety. In the case of such event, cool the device in a well-ventilated place before turning on for normal use. Keep the device out of the reach of small chil-

dren. The device may cause an injury if used as a toy. When the device is operating, do not touch the metallic parts. Failing to do so may cause burns. 14 Warning and Notice To the Users Use original accessories or accessories that are authorized. Using any unauthorized acces-

sories may affect the performance of the device and violate the related national regulations about telecom terminals. Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal recep-

tion may be affected. The device is not waterproof. Keep the device dry and store it in a shady and cool place. Do not use the device immediately after a sud-

den temperature change, because dew may be generated inside and outside the device. Do not use it until it becomes dry. Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be dam-

aged. Only qualified personnel can dismantle and re-

pair the device. 15 Warning and Notice An operating temperature between 0C and

+35C and humidity between 5% and 95% are recommended. Using Battery Do not change the built-in rechargeable battery in your device by yourself. The battery can only be changed by ZTE or ZTE authorized service pro-

vider. Limited Warranty This warranty does not apply to defects or errors in the product caused by:

i. Reasonable abrasion. ii. End users failure to follow ZTEs installation, operation or maintenance instructions or proce-

dures. iii. End users mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual. 16 Warning and Notice v. Power failures, surges, fire, flood, accidents, and actions of third parties or other events out-

side ZTEs reasonable control. vi. Usage of third-party products or usage in con-

junction with third-party products if such defects are due to the combined usage. vii. Any other cause beyond the range of normal usage intended for the product. End users have no right to reject or return the prod-

uct, or receive a refund for the product from ZTE under the above-mentioned situations. This warranty is end users sole remedy and ZTE s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law. 17 Warning and Notice Limitation of Liability ZTE shall not be liable for any loss of profits or indi-

rect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. 18 LEGAL INFORMATION Copyright 2017 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, re-

produced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior writ-

ten permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print er-

rors or update specifications without prior notice. Version No.: R1.0 19 Troubleshooting Problem The connection between your device and a PC through a USB cable cannot be established. Recommended Action Install the software, and run the installation program in the path of My Computer. If the driver of your device is abnormal, reinstall the software. You need to uninstall the software first. Ensure that the Wi-Fi function is enabled. Refresh the network list and The connection between your device and a client through Wi-Fi cannot be established. select the correct SSID. Check the IP address, and ensure that your client can automatically obtain an IP address. Enter the correct network key (Wi-Fi password) when you connect the client to your device. 20 Troubleshooting Problem Recommended Action The client connected to the device cannot access the Internet. The 4G Mobile Hotspot configuration page cannot be visited. Ensure that your micro-SIM card is available. Change the location and find a place with good signal. Check the settings of the WAN connection mode. Contact your service provider and confirm your APN settings. Enter the correct address. The default address is http://192.168.0.1 or http://

ufi.ztedevice.com. Use only one network adapter in your PC. Do not use any proxy server. 21 Getting More Help You can get help by:

Sending an email to mobile@zte.com.cn Visiting www.ztedevice.com 22 ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.China Postcode: 518057 FCC RF Exposure Information (SAR) Thisdeviceisdesignedandmanufacturednottoexceedtheemissionlimitsforexposureto radio frequency (RF) energy set by the Federal Communications Commission of the United States. DuringSARtesting,thisdevicewassettotransmitatitshighestcertifiedpowerlevelinall testedfrequencybands,andplacedinpositionsthatsimulateRFexposureinusagenearthe bodywiththeseparationof10mm.AlthoughtheSARisdeterminedatthehighestcertified power level, the actual SAR level of the device while operating can be well below the maximumvalue.Thisisbecausethedeviceisdesignedtooperateatmultiplepowerlevelsso astouseonlythepowerrequiredtoreachthenetwork.Ingeneral,thecloseryouaretoa wirelessbasestationantenna,thelowerthepoweroutput. Theexposurestandardforwirelessdevicesemployingaunitofmeasurementisknownasthe SpecificAbsorptionRate,orSAR. The SAR limit set by the FCC is 1.6W/kg. This device is complied with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.11992 and had been tested in accordancewiththemeasurementmethodsandproceduresspecifiedinIEEE1528. TheFCChasgrantedanEquipmentAuthorizationforthismodeldevicewithallreportedSAR levelsevaluatedasincompliancewiththeFCCRFexposureguidelines. Forthisdevice,thehighestreportedSARvalueforusagenearthebodyis1.372W/kg. WhiletheremaybedifferencesbetweentheSARlevelsofvariouspositions,theyallmeetthe governmentrequirements. SAR compliance for bodyworn operation is based on a separation distance of 10 mm betweentheunitandthehumanbody.Carrythisdeviceatleast10mmawayfromyourbody toensureRFexposurelevelcompliantorlowertothereportedlevel.Tosupportbodyworn operation, choose the belt clips or holsters, which do not contain metallic components, to maintainaseparationof10mmbetweenthisdeviceandyourbody. RFexposurecompliancewithanybodywornaccessory,whichcontainsmetal,wasnottested andcertified,andusesuchbodywornaccessoryshouldbeavoided. FCCRegulations Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwo conditions: (1) This device may not cause harmful interference, and (2) this device must acceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation. ThisdevicehasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice, pursuanttoPart15oftheFCCRules. Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceina residential installation. This equipment generates, uses and can radiate radio frequency energyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful interferencetoradiocommunications. CAUTION: Changes or modifications not expressly approved by the party responsible for compliancecouldvoidtheusersauthoritytooperatetheequipment. Theantenna(s)usedforthistransmittermustnotbecolocatedoroperatinginconjunction withanyotherantennaortransmitter.