PK5001Z 802.11n Wireless ADSL2+ 4-port Gateway Users Manual

PK5001Z 802.11n Wireless ADSL2+ 4-port Gateway Quick Start Guide Version 3.10 2/2012 Edition 2 1 PK5001Z Quick Start Guide Overview The PK5001Z i s a wireless ADSL router with a four-port built-i n switch. This Quick Start Guide shows you how to use the PK5001Z to connect to the Internet and how to configure the device settings to connect wirelessly y. See your Users Guide for background information on all features. Quick Login Information LAN IP address http://192.168.0.1 default administrator password Check back label for the info Note: The device is designed to allow both vertical and wall mounted usage. 2 PK5001Z Quick Start Guide Hardware Connections 1 DSL: Use the gray telephone wire to connect your PK5001Zs DSL port to a telephone jack (or to the modem port on a splitter if you are using one). 2 ETHERNET: Use the yellow Ethernet cable to connect a computer to an ETHERNET port for initial configuration and/or Internet access. 3 POWER: Use the included power adaptor to connect an appropriate power source to the POWER socket. Make sure the power source is on. 4 Push in the POWER button. 5 Look at the lights on the front panel. The POWER light blinks while your PK5001Z starts up and stays on once it is ready. Each ETHERNET light stays on if the corresponding ETHERNET port is properly connected and blinks when there is traffic. The DSL light is on when the PK5001Z has a DSL connection. The INTERNET light is on when you are able to access the Internet and blinks when the PK5001Z Is sending or receiving data. Wait a couple of minutes while your device checks the connection. If any of these lights are not on, check your connections and inspect your cables for dam age. If the lights are still off, contact your local 3 vendor. PK5001Z Quick Start Guide 2 Internet Connection Setup: Automatic Use this section to have your PK5001Z automatically detect and set up your Internet connection. 1 Open your web browser to a website. Wait while your PK5001Z tries to detect your DSL connection to your ISP. This may take a few minutes. 2 After it detects the connection, the DSL light shows green on your device and the Internet light comes on when the Internet is ready for you to use. If you have a PPPoE connection, you will have to enter your user name and password. 3 Go to section 3 if you wish to configure your wireless settings. 4 If you do not see the connection test screen, or the connection test is not successful , follow the instructions i n the screen below, or check your connections and restart the PK5001Z. If you still cannot access the Internet, follow the steps in section 3. 3 Configuring your Wireless Settings To create a wireless network, the PK5001Z and your wireless computer must all use the sam e SSID (network name), channel and security 4 settings. PK5001Z Quick Start Guide If you do not set wireless security then anyone within range could use your PK5001Z to access your network and the Internet. Choose W PA-PSK wireless security if your wireless device supports it as it is stronger than W EP. Otherwise choose W EP. 1 Select Active and click Next to continue. It i s strongly recommended that Enable OTIST i s NOT selected. See section 7 for more information. 2 C o n f i g u r e your wireless settings i n the screen. Click Next. 3 If you select either WEP or WPA-PSK security (recommended), then follow the directions to enter the appropriate key. Click Next to continue and Apply to save your wireless LAN settings. 4 Check your configuration and write down your wireless LAN settings for later use. Click Finish to complete and save the wizard setup. 5 Your Internet i s ready for you to use. Open your browser and navigate to your favorite website. 4 Internet Connection Setup Using Advanced Settings Use this section to set up your Internet connection manually if you do not 5 see the ISP Parameters for Internet PK5001Z Quick Start Guide Access screen when you run the wizard (see section 4, step 4). 1 Login again. (Follow steps 1 to 5 in section 3.) 2 Select Go to Advanced setup. Then, click Apply. 3 The Status screen appears. Click Network > WAN i n the navigation panel on the left of the screen. 4 E n t e r the information exactly as provided by your ISP. Click Apply. 5 If you still cannot access the Internet, see Troubleshooting and/or contact your Internet Service Provider

(ISP) for assistance. Troubleshooting 1 If you cannot access the web configurator, Your computer may be set to use a static IP address in a different subnet from the ZyXEL device. See the appendix in the Users Guide for information on setting up your IP address. If you are using Internet Explorer in Windows XP or Windows Server 2003, make sure you allow pop-up windows, JavaScripts and Java permissions or set the Internet security level lower than High in Internet Explorer (i n Internet Explorer, click Tools > Internet Options > Security >

Custom Level...). See the appendix i n the Users Guide for more information. 6 PK5001Z Quick Start Guide 2 If you cannot access the Internet when your computer i s connected to the ETHERNET port, follow these steps. A) Check the lights on the front panel . If they are different from what i s described in section 1, make sure the PK5001Z is correctly connected.

(See section 1.) If the lights are still different, turn off the device, wait a few seconds, and turn it on again. B) Check you have correctly entered the information your ISP gave you. For example, if your account has a user name and password, make sure you type i t correctly. In addition, if you are not sure which encapsulation your ISP uses, contact your ISP. If your ISP did not give you Internet connection information, follow the steps in section 2. C) If you are using a new Internet account, contact your ISP to make sure it is active. D) If you still have problems, see Troubleshooting i n the Users Guide. If you cannot access the Internet after you take the steps above, either try the following or contact your ISP:

E) Turn your PK5001Z off and on. Open your Internet browser if it is not already open. Let the PK5001Z complete the DSL connection test (this may take several minutes). See section 2 for details. If the test is successful, check whether you can access the Internet. If you still cannot access the Internet, contact your Internet Service 7 Provider. PK5001Z Quick Start Guide 3 If you cannot access the Internet using the wireless network, follow these steps. A) On a computer i n the wireless network, open your browser, and go to http://192.168.0.1. If you see the login screen i n section 3, follow suggestions A - F above. If you do not, go to the next step. B) On a computer connected to the PK5001Z, make sure your PK5001Z and the computers on your wireless network are using the sam e wireless and wireless security settings. See the chapter on Wireless LAN in the Users Guide for more inform action. Viewing Your Products Certifications 1 Go to www.zyxel.com. 2 Select your product from the drop-down list box on the ZyXEL home page to go to that product's page. 3 Select the certification you wish to view from this page. Customer Information Statement The information informing the user of his/her and the telephone company's rights and obligations is outlined on the following pages. This 8 information will be included i n the final version of the manual. PK5001Z Quick Start Guide Customer Information 1 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On bottom of this equipment i s a label that contains, among other information, a product identifier of QW EST PK5001Z. If requested, this number must be provided to the telephone company. 2 If this equipment DL causes harm to the telephone network, the telephone company will notify you i n advance that temporary discontinuance of service may be required. But if advance notice i isnt practical, the telephone company will notify the customer as soon as possible. Al so you will be advised of your right to file a complaint with the FCC if you believe i t i s necessary. 3 The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modification to maintain uninterrupted service. 4 If you experience trouble with this equipment, you disconnect it from the network until the problem has been corrected or until you are sure that the equipment i s not malfunctioning. 5 Please follow instructions for repairing if any (e.g. battery replacement 9 section); otherwise do not alternate or repair any parts of device except PK5001Z Quick Start Guide specified. 6 Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. 7 If the telephone company requests information on what equipment is connected to their lines, inform them of:

a The ringer equivalence number i s 02 b) The USOC jack required RJ14, and c) The FCC Registration Number US: 1RODL02BPK5001Z Item (a) and (c) are indicated on the label. The ringer equivalence number

(REN) is used to determine how many devices can be connected to your telephone line. In most areas, the sum of the RENs of all devices on Any one line should not exceed five(5.0).If too many devices are attached , they may not ring properly. 8 If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable alarm equipment; consult your telephone company or a qualified installer. Certifications Federal Communications Commission (FCC) Interference Statement 10 The device complies with Part 15 of FCC rules. Operation is subject to the PK5001Z Quick Start Guide following two conditions:

. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operations. This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio/television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1 Reorient or relocate the receiving antenna. 2 Increase the separation between the equipment and the receiver. 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 11 4 Consult the dealer or an experienced radio/TV technician for help. PK5001Z Quick Start Guide FCC Radiation Exposure Statement

. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g or 802.11n (20MHz) operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IEEE 802.11n

(40MHz) operation of this product in the U.S.A. is firmware-limited to channels 3 through 9. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Safety Warnings

. Do NOT use this product near water, for example, in a wet basement or near a swimming pool. Do NOT expose your device to dampness, dust or corrosive liquids. Do NOT store things on the device. 12

. Do NOT install, use, or service this device during a thunderstorm. There PK5001Z Quick Start Guide is a remote risk of electric shock from lightning. Connect ONLY suitable accessories to the device. Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information. Make sure to connect the cables to the correct ports. Place connecting cables carefully so that no one will step on them or stumble over them. Always disconnect all cables from this device before servicing or disassembling. Use ONLY an appropriate power adaptor or cord for your device. Connect the power adaptor or cord to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe). Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord. Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution. If the power adaptor or cord is damaged, remove it from the device and the power source. 13

. Do NOT attempt to repair the power adaptor or cord. Contact your local PK5001Z Quick Start Guide vendor to Order a new one. Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device. Use only No. 26 AWG (American Wire Gauge) or larger telecommunication line cord. Antenna Warning! This device meets ETSI and FCC certification requirements when using the included antenna(s). Only use the included antenna(s). If you wall mount your device, make sure that no electrical lines, gas or water pipes will be damaged. Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately Information to user 14 The users manual or instruction manual for an intentional or PK5001Z Quick Start Guide unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. Service Requirements In the event of equipment malfunction, all repairs should be performed by our Company or an authorized agent. It is the responsibility of users requiring service to report the need for service to our Company or to one of our authorized agents. Service can be facilitated through our office at: ZyXEL Communications Corporation 6, Innovation Rd II, Science-Based Industrial Park, Shin-Chu, Taiwan, R.O.C.

+886- 3-578-3942 15