| submitted | available | document details (if available) | source link |
|---|---|---|---|
| May 05 2003 |
| various | User Manual Part 1 | Users Manual | 1.41 MiB | May 05 2003 |
Barricade ADSL Router Wireless Broadband Router with built-in ADSL Modem N Compatible with all leading DSLAMs N Firewall (hacker attack logging, DoS, and client filtering) N Supports DMT line modulation N Four auto-negotiating 10/100 Ethernet ports N Built-in print server N PPTP, L2TP, and IPSec pass through N Multiple user Internet access with a single-user account N Supports PPPoE and PPPoA N Plug & Play installation N Web-based management User Guide SMC7404WBRA Wireless Broadband Router with built-in ADSL Modem From SMCs line of award-winning connectivity solutions 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 March 2003 Part No: 750.9077 R01 Pub No: 150000018500E R01 Information furnished is believed to be accurate and reliable. However, no responsibility is assumed by our company for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of our company. We reserve the right to change specifications at any time without notice. Copyright 2003 by SMC Networks, Inc. 38 Tesla Irvine, CA 92618 All rights reserved. Printed in Taiwan Trademarks:
SMC is a registered trademark; and Barricade is a trademark of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders. LIMITED WARRANTY Limited Warranty Statement: SMC Networks, Inc. (SMC) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term. SMC will endeavor to repair or replace any product returned under warranty within 30 days of receipt of the product. The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering new products within 30 days of purchase from SMC or its Authorized Reseller. Registration can be accomplished via the enclosed product registration card or online via the SMC Web site. Failure to register will not affect the standard limited warranty. The Limited Lifetime warranty covers a product during the Life of that Product, which is defined as the period of time during which the product is an Active SMC product. A product is considered to be Active while it is listed on the current SMC price list. As new technologies emerge, older technologies become obsolete and SMC will, at its discretion, replace an older product in its product line with one that incorporates these newer technologies. At that point, the obsolete product is discontinued and is no longer an Active SMC product. A list of discontinued products with their respective dates of discontinuance can be found at:
http://www.smc.com/index.cfm?action=customer_service_warranty. All products that are replaced become the property of SMC. Replacement products may be either new or reconditioned. Any replaced or repaired product carries either a 30-day limited warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible for any custom software or firmware, configuration information, or memory data of Customer contained in, stored on, or integrated with any products returned to SMC pursuant to any warranty. Products returned to SMC should have any customer-installed accessory or add-on components, such as expansion modules, removed prior to returning the product for replacement. SMC is not responsible for these items if they are returned with the product. Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC. Proof of purchase may be required. Any product returned to SMC without a valid Return Material Authorization (RMA) number clearly marked on the outside of the package will be returned to customer at customers expense. For warranty claims within North America, please call our toll-free customer support number at (800) 762-4968. Customers are responsible for all shipping charges from their facility to SMC. SMC is responsible for return shipping charges from SMC to customer. i LIMITED WARRANTY WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMERS SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMCS OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMERS OR ANY THIRD PERSONS MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase. SMC Networks, Inc. 38 Tesla Irvine, CA 92618 ii COMPLIANCES Mobile of end product Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada. Cet appareil numrique respecte les limites de bruits radiolectriques applicables aux appareils numriques de Classe B prescrites dans la norme sur le matrial brouilleur: Appareils Numriques, NMB-003 dicte par lIndustrie. iii COMPLIANCES Australia AS/NZS 3548 (1995) - Class B SMC contact for products in Australia is:
SMC-Australia L9, 123 Epping Rd., North Ryde, NSW Australia Phone: 61-2-88757887 Fax: 61-2-88757777 EC Conformance Declaration - Class B This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:
RFI Emission: Limit class B according to EN 55022:1998 Limit class B for harmonic current emission according to EN 61000-3-2/
1995 Limitation of voltage fluctuation and flicker in low-voltage supply system according to EN 61000-3-3/1995 Immunity:
Product family standard according to EN 55024:1998 Electrostatic Discharge according to EN 61000-4-2:1995
(Contact Discharge: 4 kV, Air Discharge: 8 kV) Radio-frequency electromagnetic field according to EN 61000-4-3:1996
(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m) Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC power supply: 1 kV, Data/Signal lines: 0.5 kV) Surge immunity test according to EN 61000-4-5:1995
(AC/DC Line to Line: 1 kV, AC/DC Line to Earth: 2 kV) Immunity to conducted disturbances, Induced by radio-frequency fields:
EN 61000-4-6:1996 (0.15~80 MHz with 1 kHz AM 80% Modulation: 3 V/m) Power frequency magnetic field immunity test according to EN 61000-4-8:1993 (1 A/m at frequency 50 Hz) Voltage dips, short interruptions and voltage variations immunity test according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%
Reduction @500 ms, >95% Reduction @5000 ms) LVD:
EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997) iv COMPLIANCES Safety Compliance Wichtige Sicherheitshinweise (Germany) 1. Bitte lesen Sie diese Hinweise sorgfltig durch. 2. Heben Sie diese Anleitung fr den spteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gert vom Stromnetz zu trennen. Verwenden Sie keine Flssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschlu steckdose soll nahe dem Gert angebracht und leicht zugnglich sein. 5. Das Gert ist vor Feuchtigkeit zu schtzen. 6. Bei der Aufstellung des Gertes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen knnte Beschdigungen hervorrufen. 7. Die Belftungsffnungen dienen der Luftzirkulation, die das Gert vor berhitzung schtzt. Sorgen Sie dafr, da diese ffnungen nicht abgedeckt werden. 8. Beachten Sie beim Anschlu an das Stromnetz die Anschluwerte. 9. Verlegen Sie die Netzanschluleitung so, da niemand darber fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden. 10. Alle Hinweise und Warnungen, die sich am Gert befinden, sind zu beachten. 11. Wird das Gert ber einen lngeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer berspannung eine Beschdigung vermieden. 12. Durch die Lftungsffnungen drfen niemals Gegenstnde oder Flssigkeiten in das Gert gelangen. Dies knnte einen Brand bzw. elektrischen Schlag auslsen. 13. ffnen sie niemals das Gert. Das Gert darf aus Grnden der elektrischen Sicherheit nur von authorisiertem Servicepersonal geffnet werden. 14. Wenn folgende Situationen auftreten ist das Gert vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu berprfen:
a. Netzkabel oder Netzstecker sind beschdigt. b. Flssigkeit ist in das Gert eingedrungen. c. Das Gert war Feuchtigkeit ausgesetzt. d. Wenn das Gert nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e. Das Gert ist gefallen und/oder das Gehuse ist beschdigt. f. Wenn das Gert deutliche Anzeichen eines Defektes aufweist. 15. Zum Netzanschlu dieses Gertes ist eine geprfte Leitung zu verwenden. Fr einen Nennstrom bis 6 A und einem Gertegewicht grer 3 kg ist eine Leitung nicht leichter als H05VV-F, 3G, 0.75 mm2 einzusetzen. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betrgt 70 dB(A) oder weniger. v COMPLIANCES vi TABLE OF CONTENTS 1 2 3 Introduction . 1-1 About the Barricade . 1-1 Features . 1-1 Applications . 1-2 Installation . 2-1 Package Contents . 2-1 System Requirements . 2-2 Hardware Description . 2-3 LED Indicators . 2-4 ISP Settings . 2-5 Connect the System . 2-5 Connect the ADSL Line . 2-5 Phone Line Configuration . 2-6 Connect the Power Adapter . 2-8 Configuring Client PC . 3-1 TCP/IP Configuration . 3-1 Windows 95/98/Me . 3-2 Disable HTTP Proxy . 3-5 Obtain IP Settings from Your ADSL Router . 3-7 Windows NT 4.0 . 3-8 Disable HTTP Proxy . 3-10 Obtain IP Settings from Your Barricade . 3-11 Windows 2000 . 3-13 Disable HTTP Proxy . 3-14 Obtain IP Settings from Your Barricade . 3-15 Windows XP . 3-17 Disable HTTP Proxy . 3-19 Obtain IP Settings from Your Barricade . 3-19 Configuring Your Macintosh Computer . 3-21 Disable HTTP Proxy . 3-23 Obtain IP Settings from Your Barricade . 3-25 vii TABLE OF CONTENTS Configuring the Barricade . 4-1 Navigating the Web Browser Interface . 4-2 Making Configuration Changes . 4-2 Setup Wizard . 4-3 Time Zone . 4-3 Internet Sharing . 4-4 Disable Internet Sharing - Parameter Setting . 4-5 Disable Internet Sharing - Finish . 4-6 PPPoE & PPPoA - Parameter Setting . 4-7 PPPoE & PPPoA - Finish . 4-8 Multiple Protocol over ATM Mode - Parameter Setting . 4-10 Multiple Protocol over ATM Mode - Finish . 4-11 Advanced Setup . 4-13 System Settings . 4-15 Time Zone . 4-15 Password Settings . 4-16 Remote Management . 4-17 DNS . 4-18 WAN . 4-19 PPPoE (PPP over Ethernet) . 4-19 ATM . 4-21 ISP . 4-22 LAN . 4-23 Wireless . 4-25 Channel and SSID . 4-26 Encryption . 4-28 MAC Address Filtering . 4-29 NAT . 4-30 Address Mapping . 4-30 Virtual Server . 4-31 Routing System . 4-33 Static Route . 4-33 RIP . 4-34 Routing Table . 4-36 4 viii TABLE OF CONTENTS Firewall . 4-37 Access Control . 4-38 URL Blocking . 4-40 Schedule Rule . 4-41 Intrusion Detection . 4-42 DMZ . 4-46 SNMP . 4-47 Community . 4-47 Trap . 4-48 ADSL . 4-49 Parameters . 4-49 Status . 4-50 Tools . 4-53 Configuration Tools . 4-53 Firmware Upgrade . 4-54 Reset . 4-55 Status . 4-56 Finding the MAC address of a Network Card . 4-57 Windows 95/98/ME . 4-57 Windows NT4/2000/XP . 4-57 Linux . 4-57 5 Configuring Printer Services . 5-1 Printer Server Setup in Windows 95/98/Me . 5-1 Printer Server Setup in Windows NT . 5-4 Printer Server Setup in Windows 2000 . 5-6 Printer Server Setup in Windows XP . 5-8 Printer Server Setup in Unix Systems . 5-18 ix TABLE OF CONTENTS A B Troubleshooting . A-1 Cables . B-1 Ethernet Cable . B-1 Specifications . B-1 Wiring Conventions . B-1 RJ-45 Port Connection . B-2 Pin Assignments . B-3 Straight-Through Wiring . B-3 Crossover Wiring . B-4 ADSL Cable . B-5 Specifications . B-5 Wiring Conventions . B-5 C Specifications . C-1 Glossary x CHAPTER 1 INTRODUCTION Congratulations on your purchase of the Barricade Wireless Broadband Router with built-in ADSL Modem (SMC7404WBRA). We are proud to provide you with a powerful yet simple communication device for connecting your local area network (LAN) to the Internet. For those who want to surf the Internet in the most secure way, this Router provides a convenient and powerful solution. About the Barricade The Barricade provides Internet access to multiple users by sharing a single-user account. Support is provided for both wired and wireless devices. New technology provides wireless security via WEP (Wired Equivalent Privacy) encryption and MAC address filtering. It is simple to configure and can be up and running in minutes. Features Internet connection via an RJ-11 WAN port. Local network connection via four 10/100 Mbps Ethernet ports. On-board IEEE 802.11b 11 Mbps wireless network adapter. DHCP for dynamic IP configuration, and DNS for domain name mapping. Firewall with Stateful Packet Inspection, client privileges, intrusion detection, and NAT. 1-1 INTRODUCTION NAT also enables multi-user Internet access via a single user account, and virtual server functionality (providing protected access to Internet services such as Web, FTP, e-mail, and Telnet). VPN pass-through (IPSec-ESP Tunnel mode, L2TP, PPTP). User-definable application sensing tunnel supports applications requiring multiple connections. Easy setup through a Web browser on any operating system that supports TCP/IP. Compatible with all popular Internet applications. Applications Many advanced networking features are provided by the Barricade:
Wireless and Wired LAN The Barricade provides connectivity to wired 10/100 Mbps devices, and wireless IEEE 802.11b compatible devices, making it easy to create a network in small offices or homes. Internet Access This device supports Internet access through an ADSL connection. Since many ADSL providers use PPPoE or PPPoA to establish communications with end users, the Barricade includes built-in clients for these protocols, eliminating the need to install these services on your computer. Shared IP Address The Barricade provides Internet access for up to 253 users via a single shared IP address. Using only one ISP account, multiple users on your network can browse the Web at the same time. 1-2 APPLICATIONS Virtual Server If you have a fixed IP address, you can set the Barricade to act as a virtual host for network address translation. Remote users access various services at your site using a constant IP address. Then, depending on the requested service (or port number), the Barricade can route the request to the appropriate server (at another internal IP address). This secures your network from direct attack by hackers, and provides more flexible management by allowing you to change internal IP addresses without affecting outside access to your network. DMZ Host Support Allows a networked computer to be fully exposed to the Internet. This function is used when NAT and firewall security prevent an Internet application from functioning correctly. Security The Barricade supports security features that deny Internet access to specified users, or filter all requests for specific services that administrator does not want to serve. The Barricades firewall also blocks common hacker attacks, including IP Spoofing, Land Attack, Ping of Death, IP with zero length, Smurf Attack, UDP port loopback, Snork Attack, TCP null scan, and TCP SYN flooding. WEP
(Wired Equivalent Privacy), SSID, and MAC filtering provide security over the wireless network. 1-3 INTRODUCTION Virtual Private Network (VPN) The Barricade supports three of the most commonly used VPN protocols PPTP, L2TP, and IPSec. These protocols allow remote users to establish a secure connection to their corporate network. If your service provider supports VPNs, then these protocols can be used to create an authenticated and encrypted tunnel for passing secure data over the Internet (i.e., a traditionally shared data network). The VPN protocols supported by the Barricade are briefly described below. Point-to-Point Tunneling Protocol Provides a secure tunnel for remote client access to a PPTP security gateway. PPTP includes provisions for call origination and flow control required by ISPs. L2TP merges the best features of PPTP and L2F Like PPTP, L2TP requires that the ISPs routers support the protocol. IP Security Provides IP network-layer encryption. IPSec can support large encryption networks (such as the Internet) by using digital certificates for device authentication. 1-4 CHAPTER 2 INSTALLATION Before installing the Barricade Broadband Router with built-in ADSL Modem, verify that you have all the items listed under Package Contents. If any of the items are missing or damaged, contact your local distributor or Service Provider where you acquired the router. Also be sure that you have all the necessary cabling before installing the Barricade. After installing the Barricade, refer to Configuring the Barricade on page 4-1. Package Contents After unpacking the Barricade, check the contents of the box to be sure you have received the following components:
Barricade ADSL Router (SMC7404WBRA) Power adapter One CAT-5 Ethernet cable Telephone patch cable Documentation CD This User Guide Immediately inform your retailer or Service Provider in the event of any incorrect, missing, or damaged parts. If possible, please retain the carton and original packing materials in case there is a need to return the product. 2-1 INSTALLATION System Requirements You must meet the following minimum requirements:
Internet access from your Internet Service Provider (ISP) using an ADSL modem. A PC using a fixed IP address or dynamic IP address assigned via DHCP, as well as a gateway server address and DNS server address from your service provider. A computer equipped with a 10 Mbps, 100 Mbps, or 10/100 Mbps Fast Ethernet card, a USB-to-Ethernet converter, or an IEEE 802.11b wireless network adapter. TCP/IP network protocols installed on each PC that will access the Internet. A Java-enabled Web browser, such as Microsoft Internet Explorer 4.0 or above or Netscape Communicator 4.0 or above installed on one PC at your site for configuring the Barricade. 2-2 HARDWARE DESCRIPTION Hardware Description The Barricade contains an integrated ADSL modem and connects to the Internet or to a remote site using its RJ-11 WAN port. It connects directly to your PC or to a local area network using any of the four RJ-45 Fast Ethernet LAN ports or via a wireless network adapter. Access speed to the Internet depends on your service type. Full-rate ADSL provides up to 8 Mbps downstream and 640 Kbps upstream. G.lite (or splitterless) ADSL provides up to 1.5 Mbps downstream and 512 Kbps upstream. However, you should note that the actual rate provided by specific service providers may vary dramatically from these upper limits. Data passing between devices connected to your local area network can run at up to 100 Mbps over the Fast Ethernet ports and 11 Mbps over the built-in wireless network adapter. The Barricade includes an LED display on the front panel for system power and port indications that simplifies installation and network troubleshooting. It also provides the following ports on the rear panel:
Item LAN Ports Parallel Printer Port Reset Button Power Inlet WAN Port Description Fast Ethernet ports (RJ-45). Connect devices on your local area network to these ports (i.e., a PC, hub, or switch). One parallel printer port that can be connected to a printer. This printer can then be shared by all LAN users. Use this button to reset the power and restore the default factory settings. To reset without losing configuration settings, see Reset on page 4-55. Connect the included power adapter to this inlet. Warning: Using the wrong type of power adapter may cause damage. WAN port (RJ-11). Connect your ADSL line to this port. 2-3 INSTALLATION LED Indicators Verify Status Check the power and port LED indicators. LED Power Ethernet
(4 LEDs) ADSL Syn ADSL Data Condi-
tion On Off On Flashing Off On Flashing Off Flashing Off Status The Barricade is receiving power. Normal operation. Power off or failure. Ethernet Link. Sending/Receiving data. No Link. ADSL connection is functioning correctly. Startup. ADSL connection is not established. Sending/Receiving data. No data transferring. 2-4 ISP SETTINGS ISP Settings Please collect the following information from your ISP before setting up the Barricade (for PPPoE, PPPoA or fixed IP users only):
For PPPoE and PPPoA users An ISP account user name and password ISP authentication type or script (if not PAP/CHAP) For fixed IP users IP address and subnet mask IP address for your ISPs Gateway Server and Domain Name Server Connect the System The Barricade can be positioned at any convenient location in your office or home. No special wiring or cooling requirements are needed. You should, however, comply with the following guidelines:
Keep the Barricade away from any heating devices. Do not place the Barricade in a dusty or wet environment. You should also remember to turn off the power, remove the power cord from the outlet, and keep your hands dry when you install the Barricade. Connect the ADSL Line Run standard telephone cable from the wall jack providing ADSL service to the WAN port on your Barricade. When inserting an ADSL RJ-11 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. If you are using splitterless ADSL service, add low-pass filters between the ADSL wall jack and your telephones. (These filters pass voice 2-5 INSTALLATION signals through but filter data signals out.) Phone Line Configuration Installing a Full-rate Connection If you are using a full-rate (G.dmt) connection, your service provider will attach the outside ADSL line to a data/voice splitter. In this case you can connect your phones and computer directly to the splitter as shown below:
Plain Old Telephone System (POTS) Residential Connection Point (NID) Voice Splitter Data ADSL Router or Ethernet hub or switch Figure 2-1. Installing with a Splitter 2-6 CONNECT THE SYSTEM Installing a Splitterless Connection If you are using a splitterless (G.lite) connection, then your service provider will attach the outside ADSL line directly to your phone system. In this case you can connect your phones and computer directly to the incoming ADSL line, but you will have to add low-pass filters to your phones as shown below:
Plain Old Telephone System (POTS) Residential Connection Point (NID) Voice Filter Voice
& Data Voice
& Data ADSL Router Data or Ethernet hub or switch Figure 2-2. Installing without a Splitter Attach to Your Network Using Ethernet Cabling The four LAN ports on the Barricade auto-negotiate the connection speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet, as well as the transmission mode to half duplex or full duplex. 2-7 INSTALLATION Use twisted-pair cabling to connect any of the four LAN ports on the Barricade to an Ethernet adapter on your PC. Otherwise, cascade any of the LAN ports on the Barricade to an Ethernet hub or switch, and then connect your PC or other network equipment to the hub or switch. When inserting an RJ-45 connector, be sure the tab on the connector clicks into position to ensure that it is properly seated. Warning:Do not plug a phone jack connector into an RJ-45 port. This may damage the Barricade. Notes: 1. Use 100-ohm shielded or unshielded twisted-pair cable with RJ-45 connectors for all Ethernet ports. Use Category 3, 4, or 5 for connections that operate at 10 Mbps, and Category 5 for connections that operate at 100 Mbps. 2.Make sure each twisted-pair cable length does not exceed 100 meters (328 feet). Connect the Power Adapter Plug the power adapter into the power socket on the rear of the Barricade, and the other end into a power outlet. Check to confirm the power indicator on the front panel is lit. If the power indicator is not lit, refer to Troubleshooting on page A-1. In case of a power input failure, the Barricade will automatically restart and begin to operate once the input power is restored. If the Barricade is properly configured, it will take about 30 seconds to establish a connection with the ADSL service provider after powering up. During this time the Sync indicator will flash. After the ADSL connection has been established, the ADSL Sync LED will stay on. 2-8 CHAPTER 3 CONFIGURING CLIENT PC After completing hardware setup by connecting all your network devices, you need to configure your computer to connect to the Barricade. First determine how your ISP issues your IP address. Many ISPs issue these numbers automatically using Dynamic Host Configuration Protocol
(DHCP). Other ISPs provide a static IP address and associated numbers, which you must enter manually. How your ISP assigns your IP address determines how you need to configure your computer. See this section for Windows 95/98/Me configuration. See Windows NT 4.0 on page 3-8, Windows 2000 on page 3-13, Windows XP on page 3-17, or Configuring Your Macintosh Computer on page 3-21 depending on your operating system. TCP/IP Configuration To access the Internet through the Barricade, you must configure the network settings of the computers on your LAN to use the same IP subnet as the Barricade. The default network settings for the Barricade are:
IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 Note: These settings can be changed to fit your network requirements, but you must first configure at least one computer to access the Barricades Web configuration interface in order to make the required changes. (See Configuring the Barricade on page 4-1 for instruction on configuring the Barricade.) 3-1 CONFIGURING CLIENT PC Windows 95/98/Me You may find that the instructions in this section do not exactly match your version of Windows. This is because these steps and screenshots were created from Windows 98. Windows 95 and Windows Millennium Edition are similar, but not identical, to Windows 98. 1. On the Windows desktop, click Start/Settings/Control Panel. 2. In Control Panel, double-click the Network icon. 3-2 3. 4. In the Network window, under the Configuration tab, double-click the TCP/IP item listed for your network card. In the TCP/IP window, select the IP Address tab. If Obtain an IP address automatically is already selected, your computer is already configured for DHCP. Click Cancel to close each window, and skip to Disable HTTP Proxy on page 3-5. If not, locate your IP address and subnet mask. Record the numbers in the space provided on the following page. 5. Click the Gateway tab and record the numbers listed under the Installed gateways field. WINDOWS 95/98/ME 3-3 CONFIGURING CLIENT PC 6. Click the DNS Configuration tab. Locate the DNS servers listed under the DNS Server Search Order field. Record any listed addresses. 7. After writing down your settings, check to make sure you have recorded them correctly. Click OK to close the window. 8. Windows may need your Windows 95/98/Me CD to copy some files. After it finishes copying, it will prompt you to restart your system. Click Yes and your computer will shut down and restart. TCP/IP Configuration Setting IP Address Subnet Mask Primary DNS Server Secondary DNS Server Default Gateway Host Name ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ 3-4 WINDOWS 95/98/ME Disable HTTP Proxy You need to verify that the HTTP Proxy feature of your Web browser is disabled. This is so that your browser can view the Barricades HTML configuration pages. The following steps are for Internet Explorer and Netscape. Determine which browser you use and follow the appropriate steps. Internet Explorer 1. Open Internet Explorer. 2. Click the Stop button, then click Tools/Internet Options. 3. In the Internet Options window, click the Connections tab. Next, click the LAN Settings... button. 4. Clear all the checkboxes. 5. Click OK, and then click OK again to close the Internet Options window. 3-5 CONFIGURING CLIENT PC Netscape 1. Open Netscape. 2. Click the Stop button, and then click Edit/Preferences... 3. In the Preferences window, under the Category field double-click Advanced, then click Proxies. Select Direct connection to the Internet. Click OK. 4. Repeat these steps for each Windows 95/98/Me computer connected to your Barricade. 3-6 WINDOWS 95/98/ME Obtain IP Settings from Your ADSL Router Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Barricade, you can also verify that you have configured your computer correctly. 1. On the Windows desktop, click Start/Run... 2. Type WINIPCFG and click OK. It may take a second or two for the IP Configuration window to appear. 3. In the IP Configuration window, select your network card from the drop-down menu. Click Release and then click Renew. Verify that your IP address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your Barricade is functioning. Click OK to close the IP Configuration window. 3-7 CONFIGURING CLIENT PC Windows NT 4.0 After completing the hardware setup by connecting your network devices, you need to configure your computer to connect to the Barricade. First determine how your ISP issues your IP address. Many ISPs issue these numbers automatically using Dynamic Host Configuration Protocol
(DHCP). Other ISPs provide a static IP address and associated numbers, which you must enter manually. How your ISP assigns your IP address determines how you need to configure your computer. Follow these instructions:
1. On the Windows desktop, click Start/Settings/Control Panel. 2. Double-click the Network icon. 3-8 WINDOWS NT 4.0 3. In the Network window, Select the Protocols tab. Double-click TCP/IP Protocol. 4. When the Microsoft TCP/IP Properties window open, select the IP Address tab. 5. 6. In the Adapter drop-down list, be sure your Ethernet adapter is selected. If Obtain an IP address automatically is already selected, your computer is already configured for DHCP. Click Cancel to close each window, and skip to Disable HTTP Proxy on page 3-10. 7. In the TCP/IP Properties window, under the IP Address tab, locate your IP Address, Subnet Mask, and Default Gateway. Record these values in the spaces provided on the following page. 3-9 CONFIGURING CLIENT PC 8. Click the DNS tab to see the primary and secondary DNS servers. Record these values in the spaces provided below. 9. After writing down your IP settings, click the IP address tab. Select the Obtain IP address automatically radio button and click OK. Click OK again to close the Network window. 10. Windows may copy some files, and will then prompt you to restart your system. Click Yes and your computer will shut down and restart. TCP/IP Configuration Setting IP Address Subnet Mask Default Gateway Primary DNS Server Secondary DNS Server Host Name ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ Disable HTTP Proxy You need to verify that the HTTP Proxy feature of your Web browser is disabled. This is so that your browser can view the Barricades HTML configuration pages. Determine which browser you use and refer to Internet Explorer on page 3-5 or Netscape on page 3-6. 3-10 WINDOWS NT 4.0 Obtain IP Settings from Your Barricade Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Barricade, you will verify that you have configured your computer correctly. 1. On the Windows desktop, click Start/Programs/
Command Prompt. 2. In the Command Prompt window, type IPCONFIG /RELEASE and press the ENTER key. 3-11 CONFIGURING CLIENT PC 3. Type IPCONFIG /RENEW and press the ENTER key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your Barricade is functioning. 4. Type EXIT and press the ENTER key to close the Command Prompt window. Your computer is now configured to connect to the Barricade. 3-12 Windows 2000 1. On the Windows desktop, click Start/Settings/
Network and Dial-Up Connections. 2. Click the icon that corresponds to the connection to your Barricade. 3. The connection status screen will open. Click Properties. 4. Double-click Internet Protocol (TCP/IP). WINDOWS 2000 3-13 CONFIGURING CLIENT PC 5. 6. If there is IP Address information on the Internet Protocol (TCP/IP) Properties window, it should be recorded. Use the spaces below to record the current settings. If Obtain an IP address automatically and Obtain DNS server address automatically are already selected, your computer is already configured for DHCP. Click Cancel to close each window, and skip to Disable HTTP Proxy on page 3-14. 7. Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK or Close to close each window. TCP/IP Configuration Setting IP Address Subnet Mask Default Gateway Preferred DNS Server Alternate DNS Server ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ Disable HTTP Proxy You need to verify that the HTTP Proxy feature of your Web browser is disabled. This is so that your browser can view the Barricades HTML configuration pages. Determine which browser you use and refer to Internet Explorer on page 3-5 or Netscape on page 3-6. 3-14 WINDOWS 2000 Obtain IP Settings from Your Barricade Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Barricade, you can verify that you have configured your computer correctly. 1. On the Windows desktop, click Start/Programs/
Accessories/Command Prompt. 2. In the Command Prompt window, type IPCONFIG/RELEASE and press the ENTER key. 3-15 CONFIGURING CLIENT PC 3. Type IPCONFIG /RENEW and press the ENTER key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your ADSL Router is functioning. 4. Type EXIT and press the ENTER key to close the Command Prompt window. Your computer is now configured to connect to the Barricade. 3-16 WINDOWS XP Windows XP 1. On the Windows desktop, click Start/Control Panel. 2. In the Control Panel window, click Network and Internet Connections. 3. The Network Connections window will open. Double-click the connection for this device. 4. On the connection status screen, click Properties. 3-17 CONFIGURING CLIENT PC 5. Double-click Internet Protocol (TCP/IP). 6. 7. If there is IP Address information on the Internet Protocol (TCP/IP) Properties window, it should be recorded. Use the spaces below to record the current settings. If Obtain an IP address automatically and Obtain DNS server address automatically are already selected, your computer is already configured for DHCP. Click Cancel to close each window, and skip to Disable HTTP Proxy on page 3-19. 8. Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK or Close to close each window. TCP/IP Configuration Setting IP Address Subnet Mask Default Gateway Preferred DNS Server Alternate DNS Server ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ 3-18 WINDOWS XP Disable HTTP Proxy You need to verify that the HTTP Proxy feature of your Web browser is disabled. This is so that your browser can view the Barricades HTML configuration pages. Determine which browser you use and refer to Internet Explorer on page 3-5 or Netscape on page 3-6. Obtain IP Settings from Your Barricade Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Barricade, you can verify that you have configured your computer correctly. 1. On the Windows desktop, click Start/Programs/Accessories/
Command Prompt. 3-19 CONFIGURING CLIENT PC 2. In the Command Prompt window, type IPCONFIG/RELEASE and press the ENTER key. 3. Type IPCONFIG /RENEW and press the ENTER key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your ADSL Router is functioning. Type EXIT and press the ENTER key to close the Command Prompt window. Your computer is now configured to connect to the Barricade. 3-20 CONFIGURING YOUR MACINTOSH COMPUTER Configuring Your Macintosh Computer You may find that the instructions here do not exactly match your operating system. This is because these steps and screenshots were created using Mac OS 8.5. Mac OS 7.x and above are similar, but may not be identical to Mac OS 8.5. Follow these instructions:
1. Pull down the Apple Menu
. Click Control Panels/TCP/IP. 3-21 CONFIGURING CLIENT PC 2. 3. In the TCP/IP window, make sure Ethernet is selected in the Connect via: field. If Using DHCP Server is already selected in the Configure field, your computer is already configured for DHCP. Close the TCP/IP window, and skip to Disable HTTP Proxy on page 3-23. 4. If there is IP Address information on the TCP/IP screen, it should be recorded. Use the spaces below to record the current settings. 5. After writing down your IP settings, select Using DHCP Server in the Configure field and close the window. 6. Another box will appear asking whether you want to save your settings. Click Save. TCP/IP Configuration Setting IP Address Subnet mask Router address Name server address ____.____.____.____ ____.____.____.____ ____.____.____.____ ____.____.____.____ 3-22 CONFIGURING YOUR MACINTOSH COMPUTER Disable HTTP Proxy You need to verify that the HTTP Proxy feature of your Web browser is disabled. This is so that your browser can view the Barricades HTML configuration pages. The following steps are for Internet Explorer and Netscape. Determine which browser you use and follow the appropriate steps. Internet Explorer 1. Open Internet Explorer and click the Stop button. Click Edit/Preferences. 2. In the Internet Explorer Preferences window, under Network, select Proxies. 3. Uncheck all checkboxes and click OK. 3-23 CONFIGURING CLIENT PC Netscape 1. Open Netscape and click the Stop button. Click Edit/Preferences. 2. In the Preferences window, in the left-hand column labeled Category, select Advanced. Under the Advanced category, select Proxies. 3. Select Direct Connection to the Internet and click OK. 3-24 CONFIGURING YOUR MACINTOSH COMPUTER Obtain IP Settings from Your Barricade Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Barricade, you can verify that you have configured your computer correctly. 1. Pull down the Apple Menu
. Click Control Panels/TCP/IP. 3-25
This product uses the FCC Data API but is not endorsed or certified by the FCC