8DL5800PIRRES1 Wireless Motion Sensor Users Manaul t Users Manual

 

5800PIR-RES Wireless Motion Sensor - Installation Instructions 1 LOCATION / EMPLACEMENT No / Non / No Satisfactory /

Satisfaisant /

Satisfactorio 2 OPEN /

OUVERTURE 7.5 - 8 ft

(2.3 - 2.4 m) 3 CONNECT THE BATTERY, ENROLL THE SENSOR, CONDUCT GO / NO GO TEST, AND PERFORM WALK TEST / METTRE LES PILES EN PLACE , See page 2 for ENROLL THE SENSOR, CONDUCT GO / NO GO more information /

TEST, AND PERFORM WALK TEST See page 2 for more information Panasonic CR123A /

Duracell DL123A /

Honeywell 466 Observe correct polarity /

Observe correct polarity A DETECTION PATTERNS / COUVERTURE DE DETECTION 35' / 11m Wide Angle Animal Immune Lens

(P/N 5-532-719-00) Top View / Vue de Dessus 13'

4m 20'

6m 7'

2m 35'

11m 27'

8m 0 20'

6m 18 19 20 12 13 14 15 16 17 1 2 3 4 5 6 7 8 9 10 11 13'

4m 7'

2m 0 7'

2m 13'

4m 20'

6m Side View / Vue de Cote 7'

2m 13'

4m 20'

6m 27'

8m 35'

11m 0 7'6"

(2.3m) 0 PRELIMINARY DRAFT 8/24/09 4 MOUNT / INSTALLATION TOP 1

- Use only left OR right side corner mounting holes. Recommended Screws: #6 (3.5 mm) 2 B ACCESSORIES / ACCESSOIRES SMB-10 1

(P/N 0-000-110-01) SMB-10C

(P/N 0-000-111-01) SMB-10T 1

(P/N 0-000-155-01) IS2500-HSLK 1 35 x 40 (11 m x 12 m) IS2500-PALK 2 35 x 40 (11 m x 12 m) Swivel Mount Bracket Swivel Mount Ceiling Bracket Swivel Mount Bracket w/Tamper High Security Lens Kit Pet Alley Lens Kit 1 Not verified by ETL. Mounting Height:

Hauteur de montage:

Altura de la instalacin:

1 7 9 ft (2.1 m 2.7 m). 2 4 ft (1.2 m).

- 1 -

1 2 5800PIR-RES Wireless Motion Sensor - Installation Instructions ENROLL THE SENSOR Enroll the sensor in the control panel prior to its usage in the system. Refer to the control panel instructions for programming details. Program the sensor as an RF type (supervised RF) device. To enroll: connect the battery and wait for power up to end

(see LED Indications table). When prompted for the serial number, activate the sensor (wave a hand in front of the lens) to enroll the sensor. SPECIFICATIONS Power: Battery* (included). TROUBLESHOOTING Problem: The system displays a low battery message. Solution: Replace the battery within 7 days. 1 x 3 V, Lithium;

CR123A / DL 123A / 466 Loop 1 Pulse count 2; Up to 80 lbs. Animal Immunity LED INDICATIONS Condition Power Up Walk Test Indicator LED Blinks once per second (for < 45 seconds) ON for 3 seconds = Loop 1 / Low Sensitivity Alarm Flickers rapidly for 3 seconds = walk test period ended MOUNT THE SENSOR (See page 1) Before mounting the transmitter permanently, conduct Go/No Go tests (see control panel manual) to verify adequate signal strength and reorient or relocate the sensor if necessary. For Animal (Pet) Immunity:

Install the sensor where animals cannot come within 6 ft

(1.8 m) of the sensor by climbing on furniture or other objects. Aim the sensor away from stairways, furniture or other objects that can be climbed on by animals. Do not use optional swivel mount brackets. WALK TESTING The 10 minute walk test mode begins after power up, and can be restarted by removing and replacing the battery. As you walk through the detection pattern, the sensor LED will light for 3 seconds to indicate each alarm detection. Note: In walk test mode all transmissions will be sent as they occur. During normal operation, only one transmission sequence will occur within a 3-minute period to conserve battery life. 345 MHz 14 to 131 F (-10 to 55 C) Battery Life, years (typical): 5 RF Frequency:

Operating Temperature:

(for indoor use environment) Relative Humidity, no condensation:

Detectable Walk Rate:

Temperature Compensation: Advanced Dual Slope 95% max. 0.7 7ft/Sec. (0.2 2.0m/Sec.)

* Battery Caution: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212 F (100 C), or incinerate. Dispose of used batteries promptly. Keep away from children. APPROVALS / LISTINGS FCC part 15, Class B verified IC, ICES-003, Class B verified C-Tick CE SIA-PIR-01 Passive Infrared detector standard features for false alarm immunity. cETLus Listed COMPLIANCE NOTES Product must be tested at least once each year. Product must be installed within the protected area only. FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/television technician for help. The user is cautioned that changes or modifications not expressly approved by Honeywell could void the users authority to operate this equipment. IC NOTICE: This Class B digital device complies with the Canadian ICES-003. Cet appareil numrique de la Classe B est conforme la norme NMB-003 du Canada. This device complies with Part 15 of the FCC Rules and RSS-210 of the IC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & la norme CNR-210 des rgles dIC. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes ; (1) il ne doit pas produire de brouillage, et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. To obtain applicable EU compliance Declaration of Conformity for this product, please refer to our Website, http://www.security.honeywell.com/hsce/international/index.html. 2009 Honeywell International Inc. Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved. Assembled in Mexico. For the latest U.S. warranty information, please go to: www.honeywell.com/security/hsc/resources/wa or Please contact your local authorized Honeywell representative for product warranty information. PRELIMINARY DRAFT 8/24/09 800-04182V1, P/N 800-04182V1 Rev A 3/12

- 2 -