8DL5818MN Door Window Security Transmitter user manual

K9485V1 10/05 Rev. B ADEMCO 5818MNL Recessed Door Transmitter INSTALLATION AND SETUP GUIDE 5818MN TRANSMITTER FRAME OF DOOR 1/2" MAXIMUM MAGNET

"IN" SIDE OF DOOR EXTERNAL PHYSICAL BARRIER

(e.g. MOLDING) Figure 1: Door Installation 1 V

-

2 0 0

-

N M 8 1 8 5 GENERAL INFORMATION The 5818MNL Recessed Door Transmitter is a single-

zone, reed switch magnetic contact sensor that provides concealed protection for a door. It is intended for use only with alarm systems that support 5800 series devices. The transmitter is powered by one AAA Lithium (or alkaline) battery that is easily replaced when a low battery condition is indicated by the control panel. PROGRAMMING Each 5818MNL has its own unique identification code

(serial number) permanently assigned during manufacture. You must enroll the transmitters serial number in the control panel before it will operate in the system. Note: During programming of the control panel, 5818MNL transmitters must be enrolled as Input Type 3 (Supervised RF), Loop 1 (mandatory for UL installations). INSTALLATION Note: Do not use on metal frame doors. Mounting Before selecting the mounting location, please read the following:

The preferred direction of mounting is vertical, although the 5818MNL may be mounted in any direction if satisfactory its transmissions is obtained. reception of A physical barrier (e.g., a molding strip on the door frame) should be present to protect against defeat of the contact from outside the premises. Make sure that no more than 1/2 gap exists between the faces of the transmitter and magnet cases when they are installed and set. installed, an alarm signal must be obtained before a separation of 2 is reached as the door is opened. Once TRANSMITTER CASE ANTENNA REED SWITCH 0 V

-

1 0 0

-

N M 8 1 8 5 END CAP PC BOARD Figure 2: Battery/Transmitter Assembly 1. Select a location for the transmitter on the door frame (never on the hinged edge). Caution: Do not install in the door. 2. Select the location for the magnet on the door, 3. Tape in the together as described directly opposite the transmitter location. transmitter and magnet their approximate locations (with battery installed and unit the BATTERY INSTALLATION / REPLACEMENT section below and conduct Go/No Go tests (refer to control to verify adequate signal panels strength. Reorient or if necessary. instructions) transmitter relocate in 4. Mark the selected locations. 5. Drill holes at the locations marked. The transmitter will require a 3/4 diameter hole in the edge of the frame, at least 3 deep. The magnet will require a 3/8 diameter hole in the edge of the door at least 1/2 deep. 6. Insert the transmitter and magnet cases into their respective holes, so that their ends are flush with the surface. DO NOT hammer in place with hard blows. If necessary, tap gently with a rubber mallet or wood block. The transmitter case may be secured by two #4 flat head, self-tapping screws via the holes in its mounting flanges can be snapped off by scoring around them first with a sharp knife. If necessary, either case may be secured with a flanges, or the suitable adhesive. NOTE: A closure plug is supplied to cover an empty transmitter hole if it becomes necessary to relocate the transmitter. BATTERY INSTALLATION/REPLACEMENT 1. Remove the transmitters end cap by inserting the flat blade of a screwdriver in the caps slot and turning slightly counterclockwise. 2. Slide the transmitter PCB assembly out of its case, taking care not to bend the antenna during this step or later. 3. Remove the old battery, if replacing it. SPECIFICATIONS Dimensions: ..................... 3.0 H x 0.66 W x 0.8 D

(76.2mm) x (14.0mm) x (20.3mm) Gap (xmtr to magnet): .................0.5 (12.7mm) max Operating temperature: .0 - 50 C, non-condensing 4. Observe correct polarity and insert the fresh battery into the battery holder (position the battery as shown in Figure 2). 5. Slide the PCB assembly back into its case, battery end first (the reed switch end must be close to the end cap). 6. Replace the end cap. Line up the projections on the cap with the openings at the edge of the case. Press the cap gently against the PCB and turn the cap (via its slot) slightly clockwise, thereby locking it in place. Battery: ......................... 1.5VDC, AAA Lithium

(Energizer L92) or AAA Alkaline (Duracell MX2400, Panasonic AM-4PI, Eveready Energizer EN92) BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212 F (100 C) or incinerate. Dispose of used batteries properly. Keep away from children. This device complies with Part 15 of the FCC Rules, RSS210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2), this device must accept any interference received, including interference that may cause undesired operation. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC STATEMENT Note: For UL certified installations, this product is Listed for Residential use only. For the latest warranty information, please go to:

http://www.security.honeywell.com/hsc/resources/wa/index.html 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright 2008 Honeywell International Inc. www.security.honeywell.com K9485V1m K9485V1 10/05 Rev. B