submitted | available | document details (if available) | source link |
---|---|---|---|
K9230V3_blueline_Ademco_5820L_instruct_exterior.eps Barto, Bill (S&FS) Acrobat Distiller 9.0.0 (Windows) |
various | Users Manual | Users Manual | 275.65 KiB |
P erforatio n (1/4" x 1/8") FEDERAL COMMUNICATIONS COMMISSION STATEMENTS:
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. See inside of carton for Installation Instructions MOUNTING HOLE TAMPER PROTECTION MOUNTING HOLE BATTERY
(1.5VDC, AAA LITHIUM. SEE NOTE INSIDE.) TAMPER SWITCH
+
Tamper Protection Front and back-case tamper is provided using the same switch. The front-case tamper is always enabled. Adding the third screw as shown in the figure enables the back-case tamper. ASSEMBLED IN MEXICO 2009 Honeywell International Inc. All Rights Reserved S A D E M C O 5 8 2 0 L l i i m L n e T r a n s m i t t e r Slim Line Transmitter ADEMCO 5820L ADEMCO 5820L Slim Line Transmitter Ideal for casement and double hung windows N219 LITHIUMLITHIUM R R Long Life Battery Included
>
>
>
s n o i t a r o f r e P g n o A n o t r a C n e p O
<
<
<
l s r o t i t e p m o c l s o o t l i a c e p s o n s e r i u q e r e s a c n e p o o t y s a E f o e z i s e h t f l a h y l r a e n s i n g i s e d k e e l S
) k c a b d n a t n o r f
(
n o i t c e t o r p r e p m a t e s a C i s w o d n w g n u h
-
e b u o d r o f l a e d l I y r e t t a b m u h t i l i l A A A e b a e c a l p e r y s a E r e t t i m s n a r T e n L m i L 0 2 8 5 O C M E D A S i l l E a s y r e p a c e a b e A A A l i l i t h u m b a t t e r y I C a s e t a m p e r p r o t e c t i o n
(
f r o n t d e a l l f o r d o u b e
-
h u n g w n d o w s i a n d b a c k
) E a s y t o o p e n c a s e r e q u i r e s n o s p e c a i l t o o s l l S e e k d e s g n i i s n e a r l y h a l f t h e s i z e o f c o m p e t i t o r s Slim Line Transmitter ADEMCO 5820L K9230V3H 7/11 K9230V3 Ademco K9230V3 5820L Exterior of box File: K9230V3_Blueline_Ademco_5820L_instruct_exterior.eps BATTERY CAUTION: Risk of fire, recharge, disassemble, heat above Dispose of used batteries properly. explosion and burns. Do not 212 F (100 C) or incinerate. Keep away from children. Battery Information Replace battery only with:
Energizer L92 AAA Lithium or AAA Alkaline, Duracell MX2400, Panasonic AM-4PI, Eveready Engeriger EN92. Observe correct polarity. NOTE Alkaline Battery Will Yield Less Battery Life than Lithium REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. Perforation (1/4 x 1/8) a w
/
s e c r u o s e r
/
c s h m o c
. l l
/
e w y e n o h
. y t i r u c e s
. w w w
/
/
:
p t t h
:
O T O G N O T A M R O F N I I Y T N A R R A W R O F 4. 5. 6. 7. Install mounting screws in the two outside mounting holes as shown in the diagram using a #1 Phillips. If the case-back tamper switch will be used, install a third screw in the middle hole. Mount the magnet
(supplied) adjacent to the two vertical positioning lines on the case side (see diagram). The gap can be one-half of an inch maximum. To reinstall the cover, position the cover so that it covers the mounted case-back, and snap-shut. The two case halves can only be fitted together in one direction. NOTE Do NOT attempt to remove the PCB from the plastic cover for any reason. MAGNET ALIGNMENT LOCATORS MAGNET GAP 0.5" MAX OPENING SLOT FCC / IC Statement:
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC &
de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes:
(1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reue y compris les interferences causant une reception indsirable. instructions. installation carton for See inside of See inside of carton for installation instructions. 5820L is a single-zone Slim-Line Door/Window contact transmitter that provides wireless notification of intrusion. NOTE During the programming of the control panel transmitter must be enrolled as Input Type 3, Supervised RF), Loop 1. Installation 1. Temporarily mount the 5820L and magnet using the double-
back tape provided. NOTE Before mounting permanently using the double-back tape or mounting screws, conduct a Go/No Go test to verify adequate signal strength and reorient or relocate the transmitter if necessary 2. If the Go/No Go test was successful, remove the transmitters cover by inserting the flat blade of a small screw-
driver into the opening slot at one end of the unit as shown in the diagram and separate the two halves. 3. The 5820L must only be mounted against a flat surface. A curved surface would cause undo stress to the unit and possible failure to operate properly. h c e T b e W y M
/
s e c r u o s e r
/
c s h m o c
. l l
/
e w y e n o h
. y t i r u c e s
. w w w
/
/
:
p I T R O P P U S E N L N O D N A N O T A T N E M U C O D R O F I t t h Ademco K9230V3 5820L Interior of box File: K9230V3_Blueline_Ademco_5820L_instruct_interior.eps K9232V2 7/11 Rev. A ADEMCO 5820L Door/Window Contact Transmitter Door/Window Contact Transmitter Door/Window Contact Transmitter Door/Window Contact Transmitter INSTALLATION AND SETUP GUIDE that transmitter GENERAL INFORMATION The 5820L is a single-zone Slim-Line Door/Window contact provides wireless notification of intrusion. The 5820L can be used only with alarm systems that support 5800 Series wireless devices. The 5820L has its own unique serial number permanently assigned during manufacture. You must enroll the transmitters serial number in the control panel before it will operate in the system. Refer to the control panels installation instructions for programming details. Note: During programming of the control panel, 5820L transmitters must be enrolled as Input Type 3 (Supervised RF), Loop 1. The transmitter is powered by one AAA Lithium (or alkaline) battery that is easily replaced when a low battery condition is indicated by the control panel. TAMPER PROTECTION Front and back-case tamper is provided using the same switch. The front-case tamper is always enabled. Adding the third screw as shown in Figure 2 enables the back-case tamper. MAGNET ALIGNMENT LOCATORS MAGNET GAP 0.5" MAX OPENING SLOT 0 V
-
1 0 0
-
0 2 8 5 Figure 1. 5820L (Typical Installation Arrangement) MOUNTING HOLE TAMPER PROTECTION MOUNTING HOLE BATTERY
(1.5VDC, AAA LITHIUM OR ALKALINE)
+
TAMPER SWITCH 1 V
-
2 0 0
-
0 2 8 5 Figure 2. 5820L Mounting/Battery Location MOUNTING The description that follows assumes that the transmitter will be mounted as shown in Figure 1, with the magnet located adjacent to the unit's left side. The transmitter may, however, be installed in any direction, as long as the relationship of the unit to the magnet is maintained as shown in Figure 1. 1. Temporarily mount the 5820L and magnet using the double-back tape supplied. Note: Before mounting the transmitter and magnet permanently using the double-back tape or mounting screws, conduct a Go/No Go test (see control's instructions) to verify adequate signal strength and reorient or relocate the transmitter if necessary. 2. If the Go/No Go test was successful, remove the transmitter's cover by inserting the flat blade of a small screwdriver into the opening slot at one end of the unit as shown in Figure 1, and separating the two halves. 4. 3. The 5820L must only be mounted against a flat surface. A curved surface would cause undue stress to the unit and possible failure to operate properly. Install mounting screws in the two outside mounting holes as shown in Figure 2 using a #1 Phillips. If the case-back tamper switch will be used, install a third screw in the middle hole. 5. 6. Mount the magnet (supplied) adjacent to the two vertical positioning lines on the case side
(see Figure 1). The gap can be one-half an inch maximum. 7. To reinstall the cover, position the cover so that it covers the mounted case-back, and snap-
shut. The two case halves can only be fitted together in one direction. Note: Do NOT attempt to remove the PCB from the plastic cover for any reason. BATTERY INSTALLATION/REPLACEMENT Replace battery only with same or equivalent type. Dispose of used batteries according to the battery manufacturers instruction. 1. Remove the transmitter's cover (if it is not off already) as described in Mounting; step 2. 2. Observe correct polarity and insert the battery provided into the battery retainer clips as shown in Figure 2. Note: Replace battery only with type specified in the Specifications paragraph. SPECIFICATIONS Dimensions: ...................... 3.0 H x 0.5 W x 0.8 D 76.2mm x 12.7mm x 20.3mm Battery: ...... 1.5VDC, AAA Lithium (Energizer L92) or AAA Alkaline, (Duracell MX2400, Panasonic AM-4PI, Eveready Energizer EN92) Gap: ......................................... 0.5 inch maximum Magnet: ...........................WA5816MAG (supplied) BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212 F (100 C) or incinerate. Dispose of used batteries properly. Keep away from children. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2), this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reue y compris les interferences causant une reception indsirable. FEDERAL COMMUNICATIONS COMMISSION STATEMENT:
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. For the latest warranty information, please go to:
http://www.security.honeywell.com/hsc/resources/wa K9232V2K K9232V2 7/11 Rev. A 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright 2008 Honeywell International Inc. http://www.honeywell.com/security
This product uses the FCC Data API but is not endorsed or certified by the FCC