8DLIPCAMWOC1 HD Wi-Fi Outdoor Camera Users Manual

IPCAM-WOC1 HD Wi-Fi Outdoor Video Camera Quick Installation Guide IPCAM-WOC1 is a 1080p, full HD Wi-Fi video camera intended for outdoor use with Honeywell Total Connect 2.0. BETA Camera setup requires a Total Connect 2.0 account and the new Total Connect 2.0 mobile app. Video Services must be enabled in AlarmNet 360. Camera operation requires minimum available bandwidth of 2.1 Mbps. Package Contents A. Sun shield B. Camera C. Power cable extension [7 cable]

D. Power adapter with 8 cable E. Pig-tail power cable F. Mounting screws and Allen wrench G. Antenna a. Bluetooth antenna b. Audio (not used) c. Reset switch d. Power Planning Configuration and Installation See the other side of this sheet for more about mounting at the installation site The camera should be situated within 300 feet (91 m) of a power outlet and within the verified range of its WI-FI connection. DO NOT mount the camera within 1 foot (0.3 m) of any other wireless device. Depending on the specifics of your installation, a range extender may be needed to ensure adequate signal strength. It is strongly recommended that camera configuration be done as close as possible to the Wi-Fi router with which the camera will be linked. After successful setup, use the app to check signal strength at the installation site before mounting (over for more information on signal strength.) The power adapter must be connected to a non-switchable power outlet. The included sun shield should be attached to the camera in locations where sun glare may be a problem. IMPORTANT: You may use only ONE of the included power extension cables. This cable adds 7 feet (2.1 m) to the supplied power adapter for a total of 15 feet (4.5 meters). Alternately, you may use the pig-tail power cable to extend the power adapter cable with up to 300 feet (91 m) of 18 AWG wire, minimum. Wi-Fi Configuration and Camera Registration Download the Total Connect 2.0 app from the App Store or on Google Play.

(Look for the red Total Connect 2.0 logo.) Note: Significant differences between the iOS and Android versions of the app are noted in these instructions. For best results, configure only one camera at a time. Check these settings when you turn on your mobile devices Wi-Fi and Bluetooth:

Make sure the Bluetooth isnt connected to another device, such as headphones Wi-Fi should be on the same network your camera(s) will use Also, make sure the device is not on Silent (ringer and speaker) a. Verify that the cameras antenna is firmly connected. b. Turn on your smart devices Bluetooth and Wi-Fi. c. Launch the app and sign in with your Total Connect 2.0 account. d. Plug the power supply into an AC outlet, but:. DONT CONNECT THE POWER SUPPLY TO THE CAMERA YET! When you do, refer to the diagram at right menu at the top of the screen. If your account has more than one Location, select the appropriate one using the dropdown Press CAMERAS at the bottom (iOS) or top (Android) of the screen. (Remember that the horizontal Navigation Order can be customized in iOS.) a. At upper right, press ADD CAMERA (iOS) or b. Select the type of camera youre installing. The names of the camera models may

(Android) vary from the illustration at right. c. Name the camera and press NEXT. d. Connect the power supply to the camera. The LED at the top flashes various colors. Then, WAIT for the cameras LED to flash blue only. This may take a couple of minutes. e. Press NEXT on the app. a. On the Pair Your Camera screen, press Generate QR Code. After a brief wait, the code appears. b. Show the QR code on your device to the camera from 3 8 inches away. If you can, keep an eye on your devices screen; when the code is scanned successfully, a confirmation message will appear over the QR code. The app will also provide audible confirmation via your mobile devices speaker. Select your security systems Wi-Fi network and press NEXT. c. Enter the network password and press NEXT. Final setup begins. When setup is complete, the LED on the camera changes from steady blue, to purple and finally to steady green. The app also displays Setup Successful*. Press DONE or ADD ANOTHER CAMERA. After setup, go back to the CAMERAS page and check your newly-registered camera. Touch the preview image to launch a live stream from the camera.

*The app will tell you if you need to repeat the setup process. This involves resetting the camera, which is described in the app itself. See the other side of this sheet for more information about the required steps. Google Play and the Google Play logo are trademarks of Google Inc. Resetting the Camera If setup needs to be repeated, or to connect the camera to a different network, activate the Reset switch as seen at right. To reset the connection, press and hold the reset button until the LED on the camera starts blinking again. To join a new/different network:

o On the apps Cameras screen, press o Press and hold the Reset switch to reset all settings to their factory defaults o Unplug the camera and then reconnect it. o Repeat the registration procedure. and delete the camera from the link on its settings page. LED STATUS INDICATOR During installation Blue, blinking Power on. Ready to start setup. Blue, steady Connected to the app. Ready to complete setup. Purple, steady QR code scan is complete. Restart the Wi-Fi connection process. Green, blinking Connecting to Wi-Fi network. Setup timed out. Unplug the camera, plug it back in and restart setup process. Red, steady During operation Green, blinking Green, steady Red, blinking Connecting to Wi-Fi network. Connected to Wi-Fi and operating. Note: The camera is always ready to record but only originates live streaming video when the app calls for a live stream. Not connected to Wi-Fi. Low-light operation is indicated by four red LEDs arranged around the lens on the front of the camera. More about mounting at the installation site IPCAM-WOC1 can be wall- or ceiling-mounted. The camera can be installed with cables running along the outside of a wall, or inside the wall. For outdoor installations where cables are exposed to the weather, please protect the cable-ends with an enclosure such as a weatherproof single-gang box, available at most hardware stores. In any installation, make sure the cameras antenna is firmly connected. Checking Wi-Fi signal strength at the site using the app:

On the Cameras page, touch the camera youre setting up

(on Android, touch ) for Select Camera Information >

Signal Strength is displayed under IP Address o 60 100 Optimal o 40 60 Marginal o 00 40 Use of a range extender strongly recommended Wall mount example Ceiling mount example FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS If using an indoor antenna, have a quality outdoor antenna installed. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dIndustrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. RF EXPOSURE STATEMENT:

The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. MISE EN GARDE EXPOSITION AUX FRQUENCES RADIO:

L'antenne (s) utilise pour cet metteur doit tre installe une distance de sparation d'au moins 7,8 pouces (20 cm) de toutes les personnes. DECLARACIN IFETEL La operacin de este equipo est sujeta a las siguientes dos condiciones 1. Es posible que este equipo o dispositivo no cause interferencia perjudicial y 2. Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. TRADEMARKS Honeywell is a registered trademark of Honeywell International Inc. DECLARACIN ANATEL Este equipamento opera emcartersecundrio, isto , notemdireito a proteo contra interferncia prejudicial, mesmo de estaes do mesmotipo, e nopodecausarinterferncia a sistemas operando emcarterprimrio. For online support visit, https://mywebtech.honeywell.com/

For the latest warranty information, visit http://www.security.honeywell.com/hsc/resources/wa/

800-23672E 800-23672 9/17 Rev. A BETA 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 2017 Honeywell International Inc. www.honeywell.com/security