8DLRF6C Lyric Smart Peripheral - Contact Quick Installation Manual Users Manual

This wireless door / window contact is intended for use with Honeywell controls that support SiX series devices. FC: This wireless door / window contact is intended for use with Honeywell controls that support SiX series devices. SP: This wireless door / window contact is intended for use with Honeywell controls that support SiX series devices. PA: This wireless door /

window contact is intended for use with Honeywell controls that support SiX series devices. After enrolling and before mounting permanently, conduct Go/No Go tests (see the controllers instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary. FC: After enrolling and before mounting permanently, conduct Go/No Go tests (see controllers instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary. SP:: After enrolling and before mounting permanently, conduct Go/No Go tests (see controllers instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary. PA:: After enrolling and before mounting permanently, conduct Go/No Go tests (see controllers instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary. NOTE: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controllers instructions. NOTE: Once enrolled, the sensor cannot be used with another system until it is removed from the current controller. See the controllers instructions.. NOTE: Once enrolled, the sensor cannot be used with another system until it is removed from the current controller. See the controllers instructions.. NOTE: Once enrolled in a system, the RF6GB cannot be used with another control panel until it is removed from the current control panel. See the Controls instructions. A Terminal Block B Reed Switch C Magnet D Tamper E LED Enroll / Enroll / Enroll / Enroll Product must be tested at least once each year / Le fonctionnement du produit doit tre vrifi au moins une fois par anne /

El producto debe ser probado al menos una vez al ao / O produto deve ser testado pelo menos uma vez por ano BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212 F (100 C) or incinerate. Dispose of used batteries promptly. Keep away from children. FC:BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212 F (100 C) or incinerate. Dispose of used batteries promptly. Keep away from children. SP: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212 F (100 C) or incinerate. Dispose of used batteries promptly. Keep away from children. PA: BATTERY CAUTION:

Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212 F (100 C) or incinerate. Dispose of used batteries promptly. Keep away from children. Approval Listings:

RoHS FCC / IC ETL listed to UL1023 &

UL 634 cETL Listed to ULC/ORD 1023 & ULC/ORD 634 FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch If using an indoor antenna, have a quality outdoor antenna installed. circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une reception indsirable. RF Exposure Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Mise en Garde Exposition aux Frequences Radio: L'antenne (s) utilise pour cet metteur doit tre installe une distance de sparation d'au moins 7,8 pouces (20 cm) de toutes les personnes. Replace Battery / Replace Battery /

Replace Battery / Replace Battery REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. Support and Warranty Specifications:

Battery: 1 x 3V, Lithium; Panasonic CR123A, Duracell DL 123, Duracell DL 123A, Honeywell 466 Tamper: Cover and Wall reported separately to panel. RF Frequency: 2.4GHz Operating Temperature: 32 to 122 F / 0 50 C Relative Humidity: 5 95%, non-condensing Dimensions: 1 H x 3.13 L x 1.61 W /25.5 mm H x 79.5 mm L x 41 mm W For the latest documentation and online support information, please go to:

Pour de lassistance en ligne, visitez :

Para recibir soporte en lnea, visite:

Para qualquer informao adicional, contacte:

https://mywebtech.honeywell.com//

MyWebTech Warranty For the latest U.S. warranty information, please go to www.honeywell.com/security/hsc/resources/wa or Please contact your local authorized Honeywell representative for product warranty information. Pour obtenir de l'information sur la garantie de ce produit, veuillez communiquer avec le reprsentant autoris de Honeywell de votre rgion. Por favor contacte con su distribuidor Honeywell Security para informacin sobre la garanta del producto. Contacte o representante autorizado Honeywell local para obter informaes relativas a garantia. To protect the environment, a detailed installation guide is available on the Honeywell website Please consider before printing the document!

2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved www.honeywell.com/security 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 800-15959) 800-15959 04/15 Rev A BETA