| submitted | available | document details (if available) | source link |
|---|---|---|---|
| User's Manual for ION-U Tech Docu AMBG Microsoft® Word 2016 |
| various | user manual | Users Manual | 4.62 MiB |
ION-U ION-U EU L 17EP/17EP User's Manual M0200AJA DISCLAIMER:
This document has been developed by CommScope, and is intended for the use of its customers and customer support personnel. The information in this document is subject to change without notice. While every effort has been made to eliminate errors, CommScope disclaims liability for any difficulties arising from the interpretation of the information contained herein. The information contained herein does not claim to cover all details or variations in equipment, nor to provide for every possible incident to be met in connection with installation, operation, or maintenance. This document describes the performance of the product under the defined operational conditions and does not cover the performance under adverse or disturbed conditions. Should further information be desired, or should particular problems arise which are not covered sufficiently for the purchasers purposes, contact CommScope. CommScope reserves the right to change all hardware and software characteristics without notice. COPYRIGHT:
Copyright 2018 CommScope Inc. All Rights Reserved. This document is protected by copyright. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical photocopying, recording, or otherwise without the prior written permission of CommScope. TRADEMARKS All trademarks identified by or are registered trademarks or trademarks, respectively, of CommScope. Names of products mentioned herein are used for identification purposes only and may be trademarks and / or registered trademarks of their respective companies. Andrew Wireless Systems GmbH, 02-May-2018 Page 2 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Table of Contents TABLE OF CONTENTS 1. GENERAL 1.1. 1.2. 1.3. 1.4. 1.5. 1.6. USED ABBREVIATIONS HEALTH AND SAFETY PROPERTY DAMAGE WARNINGS COMPLIANCE ABOUT COMMSCOPE INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT 2. INTRODUCTION 2.1. 2.2. PURPOSE ION-U LOW POWER REMOTE/EXTENSION UNITS 3. FUNCTIONAL DESCRIPTION 3.1. 3.2. 3.3. GENERAL SISO AND MIMO OPERATION ION-U EU L 17EP/17EP PORTS 4. COMMISSIONING 4.1. 4.1.1. 4.1.2. 4.1.3. LOW POWER EU MECHANICAL INSTALLATION Health and Safety for mechanical installation Property Damage Warnings for mechanical installation Mounting bracket 4.1.3.1. Mount to a wall 4.1.3.2. Mount to a pole 4.1.4. 4.1.5. 4.1.6. 4.1.7. 4.2. 4.2.1. 4.2.2. 4.2.3. 4.2.4. 4.2.5. Threaded pins Wall mounting procedure Single Unit Wall mounting procedure Dual Units Pole mounting procedure single and dual LOW POWER EU ELECTRICAL INSTALLATION Health and Safety for electrical installation Property Damage Warnings for electrical installation Connections Grounding (Earthing) Mains power connection 7 7 8 8 9 13 14 16 16 16 17 17 18 21 23 23 23 23 24 24 25 27 28 30 34 35 35 35 37 38 39 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 3 4.2.6. Antenna connection 4.2.6.1. Cleaning procedure for RF cable connectors 4.2.6.2. Antenna cable connector assembly 4.2.7. 4.2.8. 4.2.9. 4.3. 4.3.1. 4.3.2. 4.4. 4.5. Expansion ports connections Control connector RS-232 LOCAL- Local Interface Control connector RS-232 CTRL LOW POWER EU ALARMS Bite and alarms Status LED alarms EXTERNAL ALARM INPUTS TROUBLESHOOTING 5. LOW POWER EU MAINTENANCE 5.1. 5.2. GENERAL EU POWER SUPPLY REPLACEMENT 6. APPENDIX 6.1. 6.1.1. 6.1.2. 6.1.3. 6.2. 6.3. ILLUSTRATIONS Dimensions and Mounting ION-U EU L Cable Kits LP RU, EU L 25T/25T, and EU L 23/23 Ports SPECIFICATIONS SPARE PARTS 7. LIST OF CHANGES INDEX 8. Table of Contents 42 43 46 48 49 49 50 50 51 52 52 53 53 54 58 58 58 60 60 63 63 64 65 Page 4 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Figures and Tables FIGURES AND TABLES figure 3-1 ION-U EU L 17EP/17EP block diagram .................................................... 17 figure 3-2 Remote Unit, SISO ................................................................................... 18 figure 3-3 Remote Unit, MIMO two units paired ........................................................ 18 figure 3-4 One RU one EU one antenna RF ............................................................. 18 figure 3-5 Two RUs one EU two antennas RF .......................................................... 19 figure 3-6 Two RUs two EUs two antennas RF ........................................................ 19 figure 3-7 Two RUs three EUs (2300 MHz Optimized) RF ....................................... 20 figure 3-8 Two RUs three EUs (RU band loss minimized) RF .................................. 20 figure 3-9 EU L 17EP/17EP connectors and Status LEDs ........................................ 21 figure 4-1 Mounting bracket ...................................................................................... 24 figure 4-2 Pole-mounting kit 4 to 18 ....................................................................... 26 figure 4-3 Pole-mounting kit 40 ................................................................................ 26 figure 4-4 EU threaded pin power supply side .......................................................... 27 figure 4-5 EU threaded pin narrow side .................................................................... 27 figure 4-6 Place EU onto wall mounting bracket single mount ............................... 28 figure 4-7 Install M6x12 screws and washers for single mount................................. 29 figure 4-8 Attach M6 nut to threaded pins for single mount ...................................... 29 figure 4-9 Completed single EU mount ..................................................................... 30 figure 4-10 1st unit placed on wall mounting bracket ................................................. 31 figure 4-11 Install M6x12 screws and washers ......................................................... 31 figure 4-12 Attach M6 nut to threaded pins ............................................................... 32 figure 4-13 2nd unit on wall mounting bracket ........................................................... 32 figure 4-14 Install M6x12 screws and washers 2nd unit ............................................. 33 figure 4-15 Attach M6 nut to threaded pins for 2nd unit ............................................. 33 figure 4-16 Completed dual unit mount ..................................................................... 34 figure 4-17 Grounding bolts ...................................................................................... 38 figure 4-18 Grounding bolt, schematic view .............................................................. 38 figure 4-19 AC power cable ...................................................................................... 39 figure 4-20 DC power cable ...................................................................................... 39 figure 4-21 Vdc/100 power cable .............................................................................. 40 figure 4-22 Connect mains plug ................................................................................ 41 figure 4-23 Antenna connection ................................................................................ 47 figure 4-24 Expansion ports ...................................................................................... 48 figure 4-25 RS-232 connector ................................................................................... 49 figure 4-26 RS-232 connector ................................................................................... 49 figure 5-1 Disconnect mains power .......................................................................... 54 figure 5-2 EU power supply location ......................................................................... 54 figure 5-3 8 EU power supply screws ....................................................................... 55 figure 5-4 EU power supply with cables .................................................................... 55 figure 5-5 EU power supply input cable .................................................................... 55 figure 5-6 EU power supply output cable .................................................................. 56 figure 5-7 EU with power supply removed ................................................................ 56 figure 5-8 EU with replacement power supply .......................................................... 56 figure 5-9 EU insert power supply ............................................................................. 57 figure 5-10 Reconnect mains power ......................................................................... 57 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 5 Figures and Tables figure 6-1 ION-U Low Power EU mounting bracket .................................................. 58 figure 6-2 ION-U Low Power Unit dimensions .......................................................... 58 figure 6-3 Installation drawing of ION-U L Unit single ............................................... 59 figure 6-4 Installation drawing of ION-U L Unit dual .................................................. 59 figure 6-5 LP RU connectors and Status LED .......................................................... 60 figure 6-6 EU L 23/23 connectors and Status LEDs ................................................. 61 figure 6-7 EU L 25T/25T connectors and Status LEDs ............................................. 62 table 1-1 List of international contact addresses ....................................................... 15 table 4-1 Specified torques ....................................................................................... 24 table 4-2 AC power cable ......................................................................................... 39 table 4-3 DC power cable ......................................................................................... 39 table 4-4 Vdc/100 power cable ................................................................................. 40 table 4-5 RS-232 connector, pin assignment ............................................................ 49 table 4-6 RS-232 connector, pin assignment ............................................................ 49 table 4-7 RS-232 LOCAL and CTRL connections .................................................... 50 table 4-8 Status LED alarms ..................................................................................... 51 table 6-1 Extension Unit Cable kit ............................................................................. 60 Page 6 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 1. General 1. General 1.1. Used Abbreviations Alternating current / Direct Current Automatic Level Control Built-In Test Equipment Base Transceiver Station Code Division Multiple Access Conformit Europenne (European Conformity) Channel Power Detection Downlink Declaration of Conformity Extension Port Electrostatic Discharge Extension Unit Global System for Mobile Communication Ground (Earth) Graphical User Interface Intercept Point 3rd order Identification Number Intelligent Optical Network Innovation, Sciences et Dveloppement conomique Canada Innovation, Science and Economic Development Canada; formerly IC / Industry Canada Light Emitting Diode Local Maintenance Terminal Long Term Evolution Multiple Input Multiple Output Mobile Station Main Unit Noise Figure Operations and Maintenance Center Optical Transceiver = SRMU (Subrack Master Unit) Power Distribution Unit Passive Intermodulation Input power Output power Power Supply Unit Revision Radio Frequency Remote Unit Receiver Single Input Single Output Simple Network Management Protocol Transmitter Uplink Universal Mobile Telecommunication System Uninterruptible Power Supply Voltage Standing Wave Ratio Wideband Code Division Multiple Access Wavelength Division Multiplex Extensible Markup Language AC/DC ALC BITE BTS CDMA CE CPD DL DoC EP ESD EU GSM GND GUI ICP3 ID No ION ISDE ISED LED LMT LTE MIMO MS MU NF OMC OTRx PDU PIM Pin Pout PSU Rev RF RU RX SISO SNMP TX UL UMTS UPS VSWR WCDMA WDM XML M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 7 1.2. Health and Safety 1. General 1. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Electrical hazard. Danger of death or fatal injury from electrical current inside the unit in operation. Before opening the unit, disconnect mains power. 3. Caution: High frequency radiation in operation. Risk of health hazards associated with radiation from the units inner conductor of the antenna port(s). Disconnect mains before connecting or replacing antenna cables. 4. Caution: High frequency radiation in operation. Risk of health hazards associated with radiation from the antenna(s) connected to the unit. Implement prevention measures to avoid the possibility of close proximity to the antenna(s) while in operation. 1.3. Property Damage Warnings 1. Attention: Due to power dissipation, the Extension Unit may reach a very high temperature. Do not operate this equipment on or close to flammable materials. Use caution when servicing the unit. 2. Attention: Only authorized and trained personnel are allowed to open the unit and get access to the inside. 3. Notice: Although the Extension Unit is internally protected against overvoltage, it is strongly recommended to ground (earth) the antenna cables close to the repeaters antenna connectors for protection against atmospheric discharge. 4. Notice: ESD precautions must be observed. Before commencing maintenance work, use the available grounding (earthing) system to connect ESD protection measures. 5. Notice: Only suitably qualified personnel are allowed to work on this unit and only after becoming familiar with all safety notices, installation, operation and maintenance procedures contained in this manual. 6. Notice: Keep operating instructions within easy reach and make them available to all users. Page 8 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 1. General 7. Notice: Read and obey all the warning labels attached to the unit. Make sure that all warning labels are kept in a legible condition. Replace any missing or damaged labels. 8. Notice: Only license holders for the respective frequency range are allowed to operate this unit. 9. Notice: Make sure the repeater settings are correct for the intended use (refer to the manufacturer product information) and regulatory requirements are met. Do not carry out any modifications or fit any spare parts, which are not sold or recommended by the manufacturer. 1.4. Compliance 1. Notice: For installations which have to comply with European EN50385 exposure compliance requirements, the following Power Density limits/guidelines (mW/cm) according to ICNIRP are valid:
0.2 for frequencies from 10 MHz to 400 MHz o o F (MHz) / 2000 for frequencies from 400 MHz to 2 GHz o 1 for frequencies from 2 GHz to 300 GHz 2. Notice: For installations, which have to comply with FCC RF exposure requirements, the antenna selection and installation must be completed in a way to ensure compliance with those FCC requirements. Depending on the RF frequency, rated output power, antenna gain, and the loss between the repeater and antenna, the minimum distance D to be maintained between the antenna location and human beings is calculated according to this formula:
where P (mW) is the radiated power at the antenna, i.e. the max. rated repeater output power in addition to the antenna gain minus the loss between the repeater and the antenna. PD (mW/cm) is the allowed Power Density limit acc. to 47 CFR 1.1310 (B) for general population / uncontrolled exposures which is o F (MHz) / 1500 for frequencies from 300MHz to 1500MHz o 1 for frequencies from 1500MHz to 100,000MHz RF exposure compliance may need to be addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of 1.1307(b)(3). M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 9
]/[][][24cmmWmWcmPDPD 1. General 3. Notice: Installation of this equipment is in full responsibility of the installer, who has also the responsibility, that cables and couplers are calculated into the maximum gain of the antennas, so that this value, which is filed in the FCC Grant and can be requested from the FCC data base, is not exceeded. The industrial boosters are shipped only as a naked booster without any installation devices or antennas as it needs for professional installation. 4. Notice: For installations which have to comply with FCC/ISED requirements:
English:
This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device complies with Health Canadas Safety Code. The installer of this device should ensure that RF radiation is not emitted in excess of the Health Canadas requirement. Information can be obtained at http://www.hc-sc.gc.ca/ewh-
semt/pubs/radiation/radio_guide-lignes_direct-eng.php. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Antenna Stmt for ISED:
This device has been designated to operate with the antennas having a maximum gain of 9 dBi. Antennas having a gain greater than 9 dBi are prohibited for use with this device without consent by ISED regulators. The required antenna impedance is 50 ohms. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 100 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. French:
Cet appareil est conforme FCC Partie15. Son utilisation est soumise Les deux conditions suivantes: (1) cet appareil ne peut pas provoquer dinterfrences et (2) cet appareil doit accepter Toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement du dispositif. Cet appareil est conforme avec Sant Canada Code de scurit 6. Le programme dinstallation de cet appareil doit sassurer que les rayonnements RF nest pas mis au-
del de Iexigence de Sant Canada. Les informations peuvent tre obtenues:
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-fra.php Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler lautorit de lutilisateur utiliser cet quipement. Antenne Stmt pour ISDE:
Ce dispositif a t dsign pour fonctionner avec les antennes ayant un gain maximal de 9 dBi. Antennes ayant un gain plus grand que 9 dBi sont interdites pour une utilisation avec cet appareil sans le consentement des organismes de rglementation dISDE. Limpdance dantenne requise est 50 ohms. Page 10 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 1. General Lantenne (s) utilis pour cet metteur doit tre install pour fournir une distance de sparation dau moins 100 cm de toutes les personnes et ne doit pas tre co-localises ou oprant en conjonction avec une autre antenne ou metteur. Les utilisateurs et les installateurs doivent tre fournis avec des instructions dinstallation de lantenne et des conditions de fonctionnement de lmetteur pour satisfaire la conformit aux expositions RF. 5. Notice: Corresponding local particularities and regulations must be observed. For national deviations, please refer to the respective documents included in the manual CD that is delivered with the unit. 6. Notice: The unit complies with Overvoltage Category II. It also complies with the surge requirement according to EN 61000-4-5 (fine protection); however, installation of an additional medium (via local supply connection) and/or coarse protection (external surge protection) is recommended depending on the individual application in order to avoid damage caused by overcurrent. For Canada and US, components used to reduce the Overvoltage Category shall comply with the requirements of IEC 61643-series. As an alternative, components used to reduce the Overvoltage Category may comply with ANSI/IEEE C62.11, CSA Certification Notice No. 516, CSA C22.2 No. 1, or UL 1449. Suitability of the component for the application shall be determined for the intended installation. 7. Note: For a Class B digital device or peripheral:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference. 8. Note: For a Class A digital device or peripheral:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 9. Note: This unit complies with European standard EN60950. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 11 1. General Required Distances between the ION-U EU L and Antennas The table below lists the distance that must be maintained between low power ION-U Extension Units and antennas. Please also see the requirements listed in the Antenna Stmt for ISED and Antenne Stmt pour ISDE on pages 10 and 11. ION-U Model Antenna gain without cable loss (dBi) ION-U EU L 17EP/17EP 9 Maximum Distance FCC ISED Meters
.502 Inches 19.76 Meters
.717 Inches 28.23 Equipment Symbols Used / Compliance Please observe the meanings of the following symbols used in our equipment and the compliance warnings:
Symbol Compliance Meaning / Warning For industrial (Part 20) signal booster:
WARNING: This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. WARNING: This is NOT a CONSUMER device. It is designed for installation by an installer approved by an ISED licensee. You MUST have an ISED LICENCE or the express consent of an ISED licensee to operate this device. AVERTISSEMENT: Ce produit NEST PAS un appareil de CONSOMMATION. Il est conu pour tre install par un installateur approuv par un titulaire de licence dISDE. Pour utiliser cet appareil, vous DEVEZ dtenir une LICENCE dISDE ou avoir obtenu le consentement exprs dun titulaire de licence autoris par ISDE. To be sold exclusively to mobile operators or authorized installers no harmonized frequency bands, operation requires license. Intended use: EU and EFTA countries Indicates conformity with the RED directive 2014/53/EU and RoHS directive 2011/65/EU. Indicates conformity with the RED directive 2014/53/EU and RoHS directive 2011/65/EU certified by the notified body no. 0700.
---
FCC
---
ISED CE CE WEEE Recycling Country specific information about collection and recycling arrangements per the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations is available on CommScopes website. http://www.commscope.com/About-Us/Corporate-Responsibility-and-Sustainability/Environment/#recycling Page 12 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 1. General 1.5. About CommScope CommScope is the foremost supplier of one-stop, end-to-end radio frequency (RF) solutions. Part of the CommScope portfolio are complete solutions for wireless infrastructure from top-of-the-tower base station antennas to cable systems and cabinets, RF site solutions, signal distribution, and network optimization. For patents see www.cs-pat.com. CommScope has global engineering and manufacturing facilities. In addition, it maintains field engineering offices throughout the world. Andrew Wireless Systems GmbH based in Buchdorf/ Germany, which is part of CommScope, is a leading manufacturer of coverage equipment for mobile radio networks, specializing in high performance, RF and optical repeaters. Our optical distributed networks and RF repeater systems provide coverage and capacity solution for wireless networks in both indoor installations and outdoor environments, e.g. tunnels, subways, in-trains, airport buildings, stadiums, skyscrapers, shopping malls, hotels and conference rooms. Andrew Wireless Systems GmbH operates a quality management system in compliance with the requirements of ISO 9001 and TL 9000. All equipment is manufactured using highly reliable material. To maintain highest quality of the products, comprehensive quality monitoring is conducted at all fabrication stages. Finished products leave the factory only after a thorough final acceptance test, accompanied by a test certificate guaranteeing optimal operation. Hereby Andrew Wireless Systems declares that the radio equipment type Repeater is in compliance with Directive 2014/53/EU. The full text of the EU declaration is available at the following internet address:
www.commscope.com/collateral/Declarations_of_Conformity/. According to the DoC, our CE-marked equipment can be used in all member states of the European Union. Note:
Exceptions of and national deviations from this intended use may be possible. To observe corresponding local particularities and regulations, please refer to the respective documents (also in national language) which are included in the manual CD delivered. To make the most of this product, we recommend you carefully read the instructions in this manual and commission the system only according to these instructions. For technical assistance and support, please also contact the local office or CommScope directly at one of the addresses listed in the following chapter. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 13 1. General 1.6. International Contact Addresses for Customer Support Canada United States CommScope Canada Andrew LLC, A CommScope Company Mail 505 Consumers Road, Suite 803 Toronto M2J 4V8, Canada Mail 620 North Greenfield Parkway Garner, NC 27529, U.S.A. Phone
+1-905-878-3457 (Office)
+1-416-721-5058 (Cell) Fax
+1-905-878-3297 E-mail wisupport@commscope.com Caribbean & South American Region CommScope Cabos do Brasil Ltda. Mail CALA Tech Support for Distributed Coverage & Capacity Solutions (DCCS) products:
Rua Guaporanga, 49 Praa Seca Rio de Janeiro RJ ZIP: 21320-180, Brazil Phone
+1-815-546-7154 (Cell)
+55-15-9104-7722 (Office) A M E R I C A S Phone +1-888-297-6433 Fax
+1-919-329-8950 E-mail wisupport@commscope.com Caribbean & Central American Region CommScope Mexico S.A. de C.V. Mail CALA Tech Support for Distributed Coverage & Capacity Solutions
(DCCS) products:
Av. Insurgentes Sur 688, Piso 6 Col. Del Valle, CP: 03100 Mexico City, Mexico Phone +52-55-1346-1900 (Office) Fax
+ 55-15-2102-4001 Fax
+52-55-1346-1901 E-mail wisupport@commscope.com E-mail wisupport@commscope.com China, India and Rest of Asia Australia & New Zealand Andrew International Corporation Andrew Corporation (Australia) Pty Ltd. Mail Room 915, 9/F Chevalier Commercial Centre 8 Wang Hoi Rd Kowloon Bay, Hong Kong Phone +852-3106-6100 Fax
+852-2751-7800 Mail A P A C Unit 1 153 Barry Road Campbellfield VIC 3061, Australia Phone +613-9300-7969 Fax
+613-9357-9110 E-mail wisupport.China@commscope.com E-mail wisupport.Australia@commscope.com Middle East & North Africa South Africa CommScope Solutions International Inc. Andrew Wireless Solutions Africa
(Branch) PO Box 48 78 22 Unit 3206, Floor 32, Jumeirah Business Center 5, Jumeirah Lakes Towers, Dubai, United Arab Emirates Mail Phone +971 4 390 09 80 Fax
+971 4 390 86 23
(PTY) LTD Africa
&
Middle East Mail 11 Commerce Crescent West Eastgate, Sandton PO Box 786117 Sandton 2146 South Africa Phone + 27 11-719-6000 Fax
+ 27 11-444-5393 E-mail wisupport@commscope.com E-mail wisupport@commscope.com Page 14 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 1. General United Kingdom Scandinavia Andrew Wireless Systems UK Ltd Andrew Norway (AMNW) Mail Unit 15, Ilex Building Mulberry Business Park Fishponds Road Wokingham Berkshire RG41 2GY, England Phone +44-1189-366-792 Fax
+44-1189-366-773 Mail P.O. Box 3066 Osloveien 10 Hoenefoss 3501 Norway Phone
+ 47 32-12-3530 Fax
+ 47 32-12-3531 E-mail wisupport.uk@commscope.com E-mail wisupport@commscope.com Germany France Andrew Wireless Systems GmbH CommScope France Mail Industriering 10 86675 Buchdorf Germany Phone +49-9099-69-0 Fax
+49-9099-69-930 E-mail wisupport@commscope.com Austria Andrew Wireless Systems (Austria) GmbH Mail Immeuble Le Lavoisier 4, Place des Vosges 92052 Courbevoie, France Phone
+33-1 82 97 04 00 Fax
+33-1 47 89 45 25 E-mail wisupport@commscope.com Switzerland CommScope Wireless Systems AG E U R O P E Mail Weglgasse 10 2320 Wien-Schwechat Austria Phone +43-1706-39-99-10 Fax
+43-1706-39-99-9 Mail Tiergartenweg 1 CH-4710 Balsthal Switzerland Phone
+41-62-386-1260 Fax
+41-62-386-1261 E-mail wisupport.austria@commscope.com E-mail wisupport.ch@commscope.com Italy Iberia Region Spain & Portugal CommScope Italy S.r.l., Faenza, Italy Andrew Espaa S.A. A CommScope Company Mail Via Mengolina, 20 48018 Faenza (RA) Italy Phone +39-0546-697111 Fax
+39-0546-682768 Mail Avda. de Europa, 4 2 pta. Parque Empresarial de la Moraleja Alcobendas, Madrid 28108, Spain Phone
+34-91-745-20 40 Fax
+34-91-661-87 02 E-mail wisupport.italia@commscope.com E-mail wisupport.iberia@commscope.com Czech Republic CommScope Solutions Czech Republic C-Com, spol. s r.o Mail Phone U Moru 888 53006 Pardubice, Czech Republic
+49 871 9659171 (Office)
+49 171 4001166 (Mobile) Fax
+49 871 9659172 E-mail wisupport@commscope.com table 1-1 List of international contact addresses M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 15 2. Introduction 2.1. Purpose 2. Introduction Mobile telephone and public safety systems transmit signals in two directions between base transceiver station (BTS) and mobile stations (MS) within the signal coverage area to carry voice and data traffic. If weak signal transmissions occur within the coverage area because of indoor applications, topological conditions or distance from the transmitter, extension of the transmission range can be achieved by means of an optical distributed antenna system
(DAS). Office buildings, sports arenas, college campuses, industrial parks, and other areas of high demand require the specialized capacity boost that an optical DAS can provide to meet increasing customer demands for voice and data. An optical DAS contains optical Master Units and a sufficient number of Remote Units to provide the necessary coverage. The number of the Remote Units depends on the coverage requirements of the DAS. The Remote Units are connected to the Master Unit with optical links. The Master Unit is the connection to the Base Transceiver Stations. The configuration of a Master Unit depends on the number of the Remote Units and the frequency range. RF signals are transported to and from the Remote Units via optical fibers. The ION-U system includes high power and low power Remote Units designed to meet the specific requirements of a given DAS. An ION-U Master Unit can support both high power and low power RUs simultaneously. 2.2. ION-U Low Power Remote/Extension Units The ION-U Low Power Remote Units are scalable and integrated with up to:
5-band (Cell700, LMR800, Cell850, PCS1900, AWS-3 1700/2100) or 6-band with additional Extension Unit 7-band with two additional Extension Units SISO capability. Two RUs can be operated as a pair for MIMO operation. These units are compatible with analog, GSM, EDGE, IS-95, CDMA2000, EVDO, W-CDMA, HSDPA, LTE and iDEN modulation standards. These Remote Units feature independent downlink and uplink gain adjustments and an integrated channel power detector for in-band spectrum and PIM analysis and end-to-end auto leveling. Page 16 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 3. Functional Description 3. Functional Description 3.1. General figure 3-1 ION-U EU L 17EP/17EP block diagram In the Downlink (DL) path, the Extension Unit provides:
RF amplification of the converted RF signal for transmission while maintaining a good signal-to-noise ratio RF filtering to reject spurious emissions In the Uplink (UL) path, the Extension Unit provides:
RF amplification to boost the signals received by the antennas to maintain a good signal-to-noise ratio RF filtering to reject spurious emissions Automatic Level Control (ALC) to adjust the RF signal level to meet blocking requirements M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 17 RFDPX 17EPAntenna combinerDPX 17EPAntenna combinerAntenna from RU1AUX from RU 2RS232 to RU1Local RS232RS232 to RU2Local RS232Antenna from EU Path 2AUX from RU 1ANT 1ANT 2PSUeCPD 1eCPD 2probe 1probe 2Antenna from EU Path 1Antenna from RU2AUX from EU Path 1AUX from EU Path 2 3. Functional Description 3.2. SISO and MIMO Operation The architecture of the ION-U low power supports both SISO and MIMO operation. MIMO operation is achieved by pairing two RUs. The following figures show views of a single Remote Unit for SISO applications and two Remote Units paired for MIMO applications. figure 3-2 Remote Unit, SISO figure 3-3 Remote Unit, MIMO two units paired The ION-U EU L 17EP/17EP Extension unit with integrated antenna port combiner together with ION-U L 7/80-85/17(E)P/19P allows for further options. Required RS-232 connections are not shown in the following drawings. Please see chapters 4.2.8, 4.2.9, and table 4-7 for more information. figure 3-4 One RU one EU one antenna RF Page 18 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U ION-U RU1E1E2A1Master Unit eo eo eo eoION-U EU L 17EP/17EPOpticalExpansionAntenna ID Antenna Ports ID Expansion Ports A1 RU1 ANT OUT EU L 17EP/17EP RU IN1 E1 RU1 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 1 A2 EU L 17EP/17EP ANT-1 Antenna 3. Functional Description figure 3-5 Two RUs one EU two antennas RF figure 3-6 Two RUs two EUs two antennas RF M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 19 ION-U RU1ION-U RU2E1E2A2A1A4A3Master Unit eo eo eo eoION-U EU L 17EP/17EPOpticalExpansionAntenna ID Antenna Ports ID Expansion Ports A1 RU1 ANT OUT EU L 17EP/17EP RU IN1 E1 RU1 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 1 A2 RU2 ANT OUT EU L 17EP/17EP RU IN2 E2 RU2 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 2 A3 EU L 17EP/17EP ANT-1 Antenna A4 EU L 17EP/17EP ANT-2 Antenna ION-U RU1ION-U EU L 17EP/17EPION-U RU2ION-U EU L 25T/25T or 23/23E1E2E3A2A1E4A6A5Master Unit eo eo eo eoA4A3OpticalExpansionAntennaID Antenna Ports ID Expansion Ports A1 RU 1 ANT OUT EU L 17EP/17EP RU IN1 E1 RU1 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 1 A2 RU 2 ANT OUT EU L 17EP/17EP RU IN2 E2 RU2 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 2 A3 EU L ANT-1 EU L 17EP/17EP EU IN1 E3 EU L 17EP/17EP EXP EU DL/UL Path 1 EU L EXP RU DL/UL Path 1 A4 EU L ANT-2 EU L 17EP/17EP EU IN2 E4 EU L 17EP/17EP EXP EU DL/UL Path 2 EU L EXP RU DL/UL Path 2 A5 EU L 17EP/17EP ANT-1 Antenna A6 EU L 17EP/17EP ANT-2 Antenna 3. Functional Description figure 3-7 Two RUs three EUs (2300 MHz Optimized) RF figure 3-8 Two RUs three EUs (RU band loss minimized) RF Page 20 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U ION-U RU1ION-U EU L 17EP/17EPION-U RU2ION-U EU L 23/23E1E2E3A2A1A3A4E4A7A8Master Unit eo eo eo eoION-U EU L 25T/25TA5A6E6E5OpticalExpansionAntennaID Antenna Ports ID Expansion Ports A1 RU 1 ANT OUT EU L 17EP/17EP RU IN1 E1 RU1 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 1 A2 RU 2 ANT OUT EU L 17EP/17EP RU IN2 E2 RU2 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 2 A3 EU L 17EP/17EP ANT-1 EU L 23/23 4-21 IN1 E3 EU L 17EP/17EP EXP EU DL/UL Path 1 EU L 25T/25T EXP RU DL/UL Path 1 A4 EU L 17EP/17EP ANT-2 EU L 23/23 4-21 IN2 E4 EU L 17EP/17EP EXP EU DL/UL Path 2 EU L 25T/25T EXP RU DL/UL Path 2 A5 EU L 23/23 ANT-1 EU L 25T/25T 4-23 IN1 E5 EU L 25T/25T EXP EU DL/UL ports Path 1 EU L 23/23 EXP DL/UL Path 1 ports A6 EU L 23/23 ANT-2 EU L 25T/25T 4-23 IN2 E6 EU L 25T/25T EXP EU DL/UL ports Path 2 EU L 23/23 EXP DL/UL Path 2 ports A7 EU L 25T/25T ANT-1 Antenna A8 EU L 25T/25T ANT-2 Antenna ION-U RU1ION-U EU L 17EP/17EPION-U RU2ION-U EU L 23/23E1E1E3A2A1A5A6E4A7A8Master Unit eo eo eo eoION-U EU L 25T/25TA4A3E6E5OpticalExpansionAntennaID Antenna Ports ID Expansion Ports A1 RU 1 ANT OUT EU L 17EP/17EP RU IN1 E1 RU1 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 1 A2 RU 2 ANT OUT EU L 17EP/17EP RU IN2 E2 RU2 EXP DL/UL ports EU L 17EP/17EP EXP RU DL/UL Path 2 A3 EU L 23/23 ANT-1 EU L 17EP/17EP EU IN1 E3 EU L 17EP/17EP EXP EU DL/UL Path 1 EU L 25T/25T EXP RU DL/UL Path 1 A4 EU L 23/23 ANT-2 EU L 17EP/17EP EU IN2 E4 EU L 17EP/17EP EXP EU DL/UL Path 2 EU L 25T/25T EXP RU DL/UL Path 2 A5 EU L 17EP/17EP ANT-1 EU L 25T/25T 4-23 IN1 E5 EU L 25T/25T EXP EU DL/UL ports Path 1 EU L 23/23 EXP DL/UL Path 1 ports A6 EU L 17EP/17EP ANT-2 EU L 25T/25T 4-23 IN2 E6 EU L 25T/25T EXP EU DL/UL ports Path 2 EU L 23/23 EXP DL/UL Path 2 ports A7 EU L 25T/25T ANT-1 Antenna A8 EU L 25T/25T ANT-2 Antenna 3. Functional Description 3.3. ION-U EU L 17EP/17EP Ports The RF, mains power, alarm, power control, and expansion ports are located on the bottom of the EU. Please see the Appendix to view other LP EU and RU port layouts. B C D F G H K A E L J I X W V U T S R Q M P O N A Expansion DL RU port path 2 M Mains power connector B Expansion UL RU port path 2 N Grounding (earthing) bolts C Expansion DL EU port path 2 O EU IN1 RF path 1 D Expansion UL EU port path 2 P EU IN2 RF path 2 E Expansion DL RU port path 1 Q RU IN1 RF path 1 F Expansion UL RU port path 1 R RU IN2 RF path 2 G Expansion DL EU port path 1 S ANT-1 RF to antenna path 1 H Expansion UL EU port path 1 T ANT-2 RF to antenna path 2 I Status LED path 2 J Status LED path 1 K Probe path 2 L Probe path 1 U Local Port RS-232 path 1 V Ctrl connector path 1 W Local Port RS-232 path 2 X Ctrl connector path 2 figure 3-9 EU L 17EP/17EP connectors and Status LEDs ANT -1, ANT-2 Antenna Ports The EU has two duplex 4.3-10 female antenna ports for transmitting and receiving signals to and from distributed antennas. These RF ports can be connected directly to antennas (i.e. using RF jumper cables) or through splitters, allowing additional antennas to be fed by the EU. S T RU IN1, RU IN2 Antenna Ports The EU has two duplex 4.3-10 female antenna ports for connecting to the antenna ports of two ION-U L Remote Units. The signals are combined and fed to the ANT-1, ANT-2 ports of the EU. K L M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 21 EU IN1, EU IN2 Antenna Ports 3. Functional Description The EU has two duplex 4.3-10 female antenna ports for connecting to the antenna ports of an ION-U EU L Expansion Unit. The signals are combined and fed to the ANT-1, ANT-2 ports of the ION-U EU L 17EP/17EP. O P Status LEDs The status LEDs the LED indicates the severity of the alarm. J I provide a visual warning of an alarm condition. The color of RU Expansion Ports The RU DL and UL Expansion ports for path 2 ports for path 1 Expansion ports of two RUs. and the RU DL and UL Expansion are QMA female connectors that are used to connect to the A B E F EU Expansion Ports The EU DL and UL Expansion ports for path 2 ports for path 1 Expansion ports of an additional EU such as an ION-U EU L 23/23. and the EU DL and UL Expansion are QMA female connectors that are used to connect to the G H C D Mains Connector The EU receives its power through the Mains connector
. The type of connector depends on the EU model. A 4-pin Amphenol connector is used for AC models and standard DC models. A 7-pin Amphenol connector is used for DC models powered by a dual cable supply. M Ctrl Connector The Ctrl connectors communication with RUs. V X are DB-9 male connectors and are used for external modem Local Port RS-232 The RS-232 ports modem communication with another EU. U W are standard DB-9 female connectors used for external Probe Port K L The probe ports the antenna outputs without disconnecting the antennas. The coupling is as follows:
are QMA measurement probes that allow the measurement of Port Coupling dB typ. 1700 MHz 41dB Page 22 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4. Commissioning Read and observe the health and safety and property damage warnings as well as the description carefully to avoid mistakes and proceed step-by-step as described. Attention: Do not operate the Extension Unit without terminating the antenna connectors. The antenna connectors may be terminated by connecting them to their respective antennas or to a dummy load. Notice: Only qualified personnel should carry out the electrical, mechanical, commissioning, and maintenance activities that require the unit to be powered on when open. When opening the Extension Unit, do not damage the warranty labels on the internal devices. The warranty is void if the seals are broken. Ensure that all connections have been performed according to chapter 4.2.3 Connections. 4.1. Low Power EU Mechanical Installation 4.1.1. Health and Safety for mechanical installation Read and observe chapter 1.2 Health and Safety. 1. Caution: Risk of injury by the considerable weight of the unit falling. Ensure there is adequate manpower to handle the weight of the system. 2. Caution: Risk of serious personal injury by equipment falling due to improper installation. The installer must verify that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components. The screws and dowels (wall anchors) used should also be appropriate for the structure of the supporting wall. 4.1.2. Property Damage Warnings for mechanical installation 1. Attention: Do not install the unit in a way or at a place where the specifications outlined in the Environmental and Safety Specifications leaflet of the supplier are not met. 2. Attention: Due to power dissipation, the unit may reach a very high temperature. Ensure sufficient airflow for ventilation. 3. Notice: Exceeding the specified load limits may cause the loss of warranty. 4. Notice: When connecting and mounting the cables (RF, optical, mains, ...) ensure that no water can penetrate into the unit through these cables. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 23 4. Commissioning 5. Notice: If any different or additional mounting material is used, ensure that the mounting remains as safe as the mounting designed by the manufacturer. The specifications for stationary use of the Unit must not be exceeded. Ensure that the static and dynamic strengths are adequate for the environmental conditions of the site. The mounting itself must not vibrate, swing or move in any way that might cause damage to the Unit. Specified torques must be observed for certain mounting procedures according to the following table:
Type Thread Specified torques Pins M 6 3.3 N-m Hex nuts Screws M 6 3.3 N-m 3.3 N-m M6 table 4-1 Specified torques 4.1.3. Mounting bracket 4.1.3.1. Mount to a wall 1. Check the suitability of the wall-mounting kit and the wall. 2. Install the mounting bracket using 4 M6 screw anchors (not included*) or suitable lag bolts according to the drilling layout. Confirm that the bracket is securely fastened to the wall. Installer must verify that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components.
* The M6 screw anchors are not included as part of the EU delivery because the suitable type depends on the on-site conditions (wall structure and materials). Use screw anchors that are appropriate for the mounting surface. figure 4-1 Mounting bracket Page 24 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4.1.3.2. Mount to a pole Mounting kits are available for poles from 4 to 18 (10.2 cm to 45.8 cm) and for 40 (1 m). 1. Mount the mounting bracket to the four screw pins of the two pole-mounting brackets with M6 plain washers (9), split lock washers (10) and self lock nuts
(8). 2. Screw a M8 nut (4) to one end of each of the eight threaded bolts and slide a plain washer
(5) on the bolt. to the inner side 3. Screw the end of the threaded bolts (with the nut and washer) the from welded nuts of the pole-
mounting bracket. Use the nuts that allow the mounting kit with the threaded bolts as close to the pole as possible. Lock the screwing by fastening the M8 nut. to mount M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 25 4. Commissioning 4. Mount the pole-mounting kit with the two brackets and M8 plain washers (5), split lock washers (6), and self lock nuts
(7) to the pole. Take care to mount the brackets congruently and not at an angle. figure 4-2 Pole-mounting kit 4 to 18 Mounting the 40 pole-mounting kit is similar, except:
the pole-mounting bracket provides no screw pins, but the mounting bracket is fastened with four screws M8 x 25 (2) and M8 self lock nuts (3). the pole-mounting bracket provides no welded nuts but all the threaded bolts are mounted with M8 plain washers (7), split lock washers (6) and nuts. figure 4-3 Pole-mounting kit 40 Page 26 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 23367 4. Commissioning 4.1.4. Threaded pins 1. Attach an M6 threaded pin to the unit by inserting it into the threaded hole adjacent to the power supply and turning it clockwise. Tighten the pin securely with a socket wrench. figure 4-4 EU threaded pin power supply side 2. Attach an M6 threaded pin to the nit by inserting it into the threaded hole above the handle and turning it clockwise. Tighten the pin securely with a socket wrench. figure 4-5 EU threaded pin narrow side M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 27 M6 threaded pinB0403A3A 4. Commissioning 4.1.5. Wall mounting procedure Single Unit 1. Follow the instructions for mounting the bracket and installing the threaded pins in chapter 4.1.3. 2. Install the unit on the wall-mounting bracket by lifting it into place and using both handles and lowering it down onto the bracket. The M6 pins must align with the slots in the bracket to support the unit. figure 4-6 Place EU onto wall mounting bracket single mount Page 28 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U B0400AKA 4. Commissioning 3. Fasten the lower section of the unit to the bracket using a washer and an M6x12 screw (on both sides). Slide a washer over each screw and then insert the screw and tighten it securely. figure 4-7 Install M6x12 screws and washers for single mount 4. Fasten the unit to the bracket using a washer and M6 nut. Slide the washer over the threaded pins that you installed previously (chapter 4.1.3) and then screw the nut onto the pins (on both sides) and tighten securely. figure 4-8 Attach M6 nut to threaded pins for single mount 5. Confirm that all screws and nuts have been fastened and the unit is securely mounted to the wall. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 29 B0400ALAM6x12 screwWasherB0400AMAM6 nutWasher 4. Commissioning figure 4-9 Completed single EU mount 4.1.6. Wall mounting procedure Dual Units 1. Follow the instructions for mounting the bracket and installing the threaded pins in chapter 4.1.3. 2. Install the first unit on the wall-mounting bracket by lifting the unit into place and lowering it down onto the bracket. The M6 pins must align with the slots in the bracket to support the unit. Note that the first unit is installed with the curved side facing you, which is the opposite of the installation procedure for single (one unit) mounting. Page 30 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning figure 4-10 1st unit placed on wall mounting bracket 3. Fasten the lower section of the first unit to the bracket using a washer and an M6x12 screw (on both sides). Slide a washer over each screw and then insert the screw and tighten it securely. figure 4-11 Install M6x12 screws and washers 4. Fasten the unit to the bracket using a washer and M6 nut. Slide the washer over the threaded pins that you installed previously (chapter 4.1.3) and then screw the nut onto the pins (on both sides) and tighten securely. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 31 B0402APAM6x12 screwWasherB0402ARA 4. Commissioning figure 4-12 Attach M6 nut to threaded pins 5. Install the second unit on the wall-mounting bracket by lifting the unit into place and lowering it down onto the bracket. The 2nd unit is reversed in direction from the 1st unit. The M6 pins must align with the slots in the bracket to support the unit. figure 4-13 2nd unit on wall mounting bracket 6. Fasten the lower section of the second unit to the bracket using a washer and an M6x12 screw (on both sides). Slide a washer over each screw and then insert the screw and tighten it securely. Page 32 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U WasherM6 NutB0402ATAB0402AVA 4. Commissioning figure 4-14 Install M6x12 screws and washers 2nd unit 7. Fasten the unit to the bracket using a washer and M6 nut. Slide the washer over the threaded pins that you installed previously (chapter 4.1.3) and then screw the nut onto the pins (on both sides) and tighten securely. figure 4-15 Attach M6 nut to threaded pins for 2nd unit 8. Confirm that all screws and nuts have been fastened and the unit is securely mounted to the wall. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 33 M6x12 screwWasherWasherM6 NutB0402AXA 4. Commissioning figure 4-16 Completed dual unit mount 4.1.7. Pole mounting procedure single and dual The pole mounting procedures are identical to the wall mounting procedures described in chapters 4.1.5 Wall mounting procedure Single Unit and 4.1.6 Wall mounting procedure Dual Units, except for the mounting of the mounting bracket described in chapter 4.1.3.2 Mount to a pole. Page 34 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4.2. Low Power EU Electrical Installation 4.2.1. Health and Safety for electrical installation Read and observe chapter 1.2 Health and Safety. 1. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Electrical hazard. Danger of death or fatal injury from electrical current inside the unit in operation. Before opening the unit, disconnect mains power. 4.2.2. Property Damage Warnings for electrical installation 1. Attention: It is compulsory to ground (earth) the unit before connecting the power supply. Grounding bolts are provided on the cabinet to connect the ground-bonding cable. 2. Attention: If the mains connector of the unit is not easily accessible, a disconnect device in the mains power circuit must be provided within easy reach. 3. Attention: A connection of the mains supply to a power socket requires the power socket to be nearby the unit. 4. Attention: Before connecting or disconnecting the mains connector at the unit, ensure that mains power supply is disconnected. 5. Attention: Make sure that an appropriate circuit breaker acting as a disconnect device (as required by IEC/EN60950-1) and an overcurrent limiting device are connected between mains power and the unit. 6. Attention: Incorrectly wired connections can destroy electrical and electronic components. 7. Notice: Although the unit is internally protected against overvoltage, it is strongly recommended to ground (earth) the antenna cables close to the antenna connectors of the unit for protection against atmospheric discharge. In areas with strong lightning, it is strongly recommended to install additional lightning protection. 8. Notice: To avoid corrosion at the connectors caused by electrochemical processes, the material of the cable connectors must not cause a higher potential difference than 0.6 V (see electrochemical contact series). M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 35 4. Commissioning 9. Notice: Use an appropriate torque wrench for the coupling torques:
-
-
for N-type connectors (2 N-m / 20 in lb) with 13/16 in opening, e. g. item no. 244379 available from the CommScope e-catalog for 4.3-10 type connectors (5 N-m, 44 in lb) with 22mm (7/8) in opening Do NOT use your hands or any other tool (e.g. a pair of pliers). This might cause damage to the connector and lead to a malfunction of the unit. 10. Notice: For unstabilized electric networks, which frequently generate spikes, the use of a voltage limiting device is advised. 11. Notice: Observe the labels on the front panels before connecting or disconnecting any cables. 12. Notice: Unused connectors must be closed with their protective covers to ensure water tightness. Page 36 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4.2.3. Connections Port/Conn LOCAL RS-232 STATUS CTRL EXPANSION RU DL Path 1/ Path 2 EXPANSION RU UL Path 1/ Path 2 EXPANSION EU DL Path 1/ Path 2 EXPANSION EU UL Path 1/ Path 2 MAINS
(Vac/Vdc) MAINS
(Vdc/100) Grounding Bolts ION-U Low Power EU Connectors/Indicators Purpose These connectors are used for external modem communication with another EU. These LEDs provide a visual warning of an alarm condition. The color of the LED indicates the severity of the alarm. These connectors are used for external modem communication with RUs. These connectors are used to connect to the DL Expansion ports of up to two Remote Units. Type DB-9 Female LED DB-9 Male QMA Female These connectors are used to connect to the UL Expansion ports of up to two Remote Units. QMA Female These connectors are used to connect to the DL Expansion ports of another Extension Unit to provide an additional band of coverage. These connectors are used to connect to the UL Expansion ports of another Extension Unit to provide an additional band of coverage. This connector provides the power to RU models that use standard AC (85 to 265 Vac) or RU models that use standard DC (-60 to -38 Vdc) power. This connector provides power to RU models used in locations where the power drawn on each cable must be limited to a maximum of 100 VA. Ground (earth) bolts for connecting the mandatory ground cable to the EU. QMA Female QMA Female Amphenol C016 Series, 4-Pin Amphenol C016 Series, 7-Pin M6 bolts, hex nut, & washers ANT 1 / ANT 2 These connectors are used for transmitting and 4.3-10 RU IN1 /
RU IN2 EU IN1 /
EU IN2 receiving signals to and from an antenna or antenna splitter. These connectors are used for transmitting and receiving signals to and from the antenna port of an RU. These connectors are used for transmitting and receiving signals to and from the antenna port of an EU. 4.3-10 4.3-10 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 37 4. Commissioning 4.2.4. Grounding (Earthing) The EU must be grounded (earthed). 1. Connect an earth-bonding cable to the grounding bolt connection provided on the outside of the unit (near the Mains connector) as shown in figure 4-17. Do not use the grounding connection to connect external devices. figure 4-17 Grounding bolts figure 4-18 Grounding bolt, schematic view 2. After loosening the hex nut(s), connect the earth-bonding cable between the two washers as illustrated in the figures above. 3. Then, fasten all parts again by tightening the hex nut(s). 4. Connect the other end of the ground wire to a suitable permanent ground following local electrical code practices. Page 38 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4.2.5. Mains power connection Before connecting electrical power to the units, the system must be grounded (earthed) as described in the previous chapter. The Mains power must be connected to the Mains connector of the unit for operation of the EU. A power cable is delivered with each EU. The type of power cable delivered is dependent on the type of power supply in the unit. The AC power cable is a 3.2 m (10.5 ft) 16 AWG cable with a 4-pin Amphenol C016 series plug on one end to connect to the EU Mains connector. The other end of the cable is un-terminated with 3 end splices to connect to the AC power source. A 10 m
(33.7 ft) AC power cable is also available as an option. 4-Pin Amphenol C016 Series Pin Name Phase Color 1 Black 2 Neutral White 3 4 Ground Green n.c. n.c figure 4-19 AC power cable table 4-2 AC power cable The standard DC power cable is a 3.2 m (10.5 ft) 13 AWG cable with a 4-pin Amphenol C016 series plug on one end to connect to the EU Mains connector. The other end of the cable is un-terminated with 2 end splices to connect to the -48 Vdc power source. 4-Pin Amphenol C016 Series Pin Name Color 1 2 3 4 n.c 48V 0V n.c. n.c Black Red n.c figure 4-20 DC power cable table 4-3 DC power cable M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 39 blackAmphenol4-PinfemaleconnectorProtectiveCap3xendsplicewhitegreenB0400A4ARUMainsConnector4321blackAmphenol 4-Pinfemale connectorProtective Cap2x end spliceredB0400A5ARU MainsConnector4321 4. Commissioning The Vdc/100 power cable is available for locations where the power drawn on each cable must be limited to a maximum of 100 VA. This cable is a 3.2 m (10.5 ft) 16 AWG cable with a 7-pin Amphenol C016 series plug on one end to connect to the EU Mains connector. The other end of the cable is un-terminated with 4 end splices to connect to the -48 Vdc power source. 7-Pin Amphenol C016 Series Pin Name 1 2 3 4 5 6 7 0V 48V n.c. 0V 48V n.c n.c Color White Black
-
Red Green
-
-
figure 4-21 Vdc/100 power cable table 4-4 Vdc/100 power cable Notice: For the AC power supply connection, a minimum cross section of 1.5 mm2 is required and for the DC power supply connection, a minimum cross section of 2.5 mm2 is required. Each wire must observe the applicable national regulations regarding loop impedance, voltage drop, and methods of installation. Make sure to connect the correct voltage to the unit. Notice: Do not connect or disconnect the power cable at the mains connector while power is on. Turn off mains* power before connecting the power cable at the unit, then, engage mains power again.
* Mains power must be interruptible with an external delay-actions mains breaker. For the mains breaker, observe the following recommendation:
120 Volt / 20 Amp max. or 240 Volt / 16 Amp, single-phase, 50 / 60 Hz AC service is needed, i.e. the external AC breaker should be 20 Amps max. for 120-Volt service or 13 to 16 Amps for 240-Volt service.
-48 Volt / 40 Amp max. DC service is needed, i.e. the external DC breaker should be 40 Amps max for -48 VDC service. For the DC power supply, observe the local regulations of the DC service provider. Use the following method to install and connect the Mains power to the EU:
1. Locate the Mains power cable that was delivered with the EU. 2. Locate or install a suitable power junction box or receptacle near the unit and route the power cable from the power source to the EU. Do not connect the cable to the units Mains connector at this time. The power source must be interruptible. Page 40 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 12457Amphenol 7-Pinfemale connectorProtective Cap4x end spliceB0400A6ARU MainsConnector 4. Commissioning 3. The Mains cable must be properly secured observing local regulations and electrical codes. Be sure to allow enough slack in the cable at the EU to plug or unplug the cable into the Mains connector. 4. Wire the power cable to the junction box or receptacle. Refer to the color code and pin numbers shown in figure 4-19 (AC cable), figure 4-20 (DC cable), or figure 4-21 (Vdc/100 cable) depending on the type of power supply used by the unit. 5. With the cables Mains plug disconnected from the EU, turn the circuit breaker on, unscrew the plugs protective cover, and carefully test the plug with a voltmeter to ensure that the voltage and polarity are correct. 6. Once the testing has been completed, turn off the circuit breaker. 7. Unscrew the protective cover from the Mains connector of the unit. 8. Insert the plug into the Mains connector (figure 4-22) and tighten the clamping ring until it is hand tight. Do not over-tighten the clamping ring. Clamping ring Mains plug Mains connector Protective cover figure 4-22 Connect mains plug M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 41 4.2.6. Antenna connection 4. Commissioning The Extension Unit has six 4.3-10 connectors. For mounting the cable connector, it is recommended to refer to the corresponding documentation of the connector manufacturer. The bending radius of the antenna cables must remain within the given specifications. The selection of cable and antenna is an important consideration. Choose the type of cable best suited for the antenna. Consider that a cable with higher loss is less expensive but impairs performance. Notice: Use an appropriate torque wrench for the coupling torques:
-
-
for N-type connectors (2 N-m / 20 in lb) with 13/16 in opening, e. g. item no. 244379 available from the CommScope e-catalog for 4.3-10 type connectors (5 N-m, 44 in lb) with 22mm (7/8) in opening Do NOT use your hands or any other tool (e.g. a pair of pliers). This might cause damage to the connector and lead to a malfunction of the unit. Attention: To minimize passive inter-modulation (PIM) distortion, attention has to be paid to the physical condition of the connector junctions:
Do not use connectors that show signs of corrosion on the metal surface. Prevent the ingress of water or dirt into the connector. Use protective caps for the connectors when not mounted. Before mounting clean the connectors with dry compressed air. Before mounting clean the mating surfaces of the connector with a lint-free alcohol-drenched cloth on a wooden or non-metallic item. Attach and torque the connectors properly. Avoid metallic abrasion when mounting the connectors by only screwing the connecting nut, but not turning the whole connector. Use a torque wrench to fasten the connector, see above. Clean the protective caps before mounting for antenna cable replacement. Page 42 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4.2.6.1. Cleaning procedure for RF cable connectors 1. What is needed for the cleaning?
a. Isopropyl alcohol or similar b. Compressed air c. Lint-free wipe d. Cotton buds 2. Remove protective cap from the RF connector. Caution: Risk of injury by flying particles when compressed air is used. Wear protective clothing, especially protective glasses. 3. Remove metal chips and small particles from the mating and inner surfaces of the connector using compressed air. Warning: Flammable material. Risk of fire. Keep away from sources of ignition. Caution: Eye irritant product. Risk of eye irritation. Avoid contact with eyes and skin. Wear protective clothing, especially protective glasses. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 43 4. Commissioning 4. Clean the connector winding with lint-free wipe drenched with isopropyl alcohol. 5. Clean the lip of the inner ring with a cotton bud drenched with isopropyl alcohol. 6. Clean the inside surface of the inner ring with a cotton bud drenched with isopropyl alcohol. 7. Clean the inside of the center conductor spring tines with a cotton bud drenched with isopropyl alcohol. Page 44 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 8. Clean in the similar way the connector of the connected cable. Remove protective caps from the unit connector first. 9. Remove metal chips and small particles from the mating and inner surfaces of the connector using compressed air. 10. Continue with the winding area using lint-free wipe drenched with isopropyl alcohol. 11. Continue with the inside mating surface of the inner ring. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 45 4. Commissioning 12. Clean the outside surface of the center pin. 4.2.6.2. Antenna cable connector assembly 1. What is needed for the connector assembly?
a. Torque wrench. b. (Adjustable) counter wrench 2. Join the connectors and turn the coupling nut until the thread grips. 3. Push in the connector until it clicks. Page 46 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4. Fasten the coupling nut hand-tight. Do not turn the connector but the coupling nut only. 5. Retain the cable connector with the counter wrench and fasten the coupling nut with the torque wrench until the torque is applied (torque wrench clicks). Torque wrench Counter wrench For angled antenna connectors use your hand to retain the cable connector and fasten the coupling nut with the torque wrench. Make sure only the coupling nut is turned, not the cable connector. Antenna cable figure 4-23 Antenna connection M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 47 4. Commissioning 4.2.7. Expansion ports connections The Expansion ports are QMA-F connectors that are used to connect to one or two Remote Units and an additional Extension Unit to provide extra bands of coverage. Ports are available for Path 1 and Path 2. The cables (1.5 m) required are included in the EU delivery 1. Connect an RF cable with QMA male connectors between the DL Expansion port connector of the RU and the RU UL port of the Extension Unit for Path 1. If a second RU is used, connect it to the RU DL expansion port of the EU for Path 2. Press the QMA connectors of the cable onto the Expansion port connectors until they click into place to connect the cable. 2. Connect an RF cable with QMA male connectors between the UL Expansion port connector of the RU and the RU UL port of the Extension Unit for Path 1. If a second RU is used, connect it to the RU UL expansion port of the EU for Path 2. Press the QMA connectors of the cable onto the Expansion port connectors until they click into place to connect the cable. 3. If an additional EU is used, connect an RF cable with QMA male connectors between the EU DL Expansion port connector of the 17EP/17EP EU to the DL Expansion port of the second Extension Unit for Path 1. Repeat the connection process for Path 2. Press the QMA connectors of the cable onto the Expansion port connectors until they click into place to connect the cable. 4. If an additional EU is used, connect an RF cable with QMA male connectors between the EU UL Expansion port connector of the 17EP/17EP EU to the UL Expansion port of the second Extension Unit for Path 1. Repeat the connection process for Path 2. Press the QMA connectors of the cable onto the Expansion port connectors until they click into place to connect the cable. figure 4-24 Expansion ports Page 48 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4.2.8. Control connector RS-232 LOCAL- Local Interface These DB-9 female connectors are used for local access to this EU part and for external modem communication between this EU and an additional downstream EU. DB-9 Female PIN Assignment 1 2 3 4 5 6 7 8 9 Booster presence IN RS232 Tx RS232 Rx n.c. GND n.c. n.c. Booster presence OUT n.c. figure 4-25 RS-232 connector table 4-5 RS-232 connector, pin assignment Connect the RS-232 cable (1.5m, contained in delivery of EU) from the LOCAL port of this EU to the CTRL port of the downstream EU. 4.2.9. Control connector RS-232 CTRL These DB-9 male connectors are used for external modem communication between this EU and an upstream RU or EU. DB-9 Male PIN Assignment 1 2 3 4 5 6 7 8 9 Booster presence OUT RS232 Rx RS232 Tx n.c. GND n.c. n.c. Booster presence IN n.c. figure 4-26 RS-232 connector table 4-6 RS-232 connector, pin assignment Connect the RS-232 cable (1.5m, contained in delivery of EU) from the CTRL port of this EU to the LOCAL port of the upstream RU or EU. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 49 4. Commissioning Typical RS-232 connections for a system with up to two Remote Units and up to three Extension Units are shown in the table below:
RS-232 LOCAL and CTRL Connections Path 1 (RU 1) Path 2 (RU 2) RU 1 LOCAL EU 1 CTRL Path 1 EU 1 LOCAL Path 1 EU 2 CTRL Path 1 EU 2 LOCAL Path 1 EU 3 CTRL Path 1 EU 3 LOCAL Path 1 Not Connected RU 2 LOCAL EU 1 CTRL Path 2 EU 1 LOCAL Path 2 EU 2 CTRL Path 2 EU 2 LOCAL Path 2 EU 3 CTRL Path 2 EU 3 LOCAL Path 2 Not Connected table 4-7 RS-232 LOCAL and CTRL connections 4.3. Low Power EU Alarms 4.3.1. Bite and alarms The Built-In Test concept comprises the monitoring of the power supplies and the power amplifiers. All alarms that occur can be checked via software at the Master Unit. Page 50 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 4. Commissioning 4.3.2. Status LED alarms For local supervision, a status LED on the connector panel of the Extension Unit adjacent to the Expansion ports provides a visual warning of an alarm condition. The color of the LED indicates the severity of the alarm. Detailed alarm information is available through the ION-U software interface. This table lists the alarm conditions and possible on-site measures that could be performed to resolve the issues responsible for triggering the alarms. Alarm Name Description Remedy Temperature Alarm too high temperature check ventilation and environment VSWR Alarm bad RF cabling / mismatched antenna RF Low Output AWS too low RF signal check cable / antenna check BTS output level/attenuator configuration/RF cabling DL AWS band alarm hw failure on RF section UL AWS band alarm hw failure on RF section change unit change unit UL Overdrive/ALC Limiting AWS too high RF signal feeding device check unit/attenuator configuration Internal bus alarm internal I2CBUS communication malfunction change unit External 1 Alarm external input alarm External 2 Alarm external input alarm Power Supply 1 Alarm internal power supply alarm Power Supply 2 Alarm internal power supply alarm check external device/ check alarm connection check external device/ check alarm connection change/verify unit change/verify unit Power Supply 1 exceeded load threshold Power Supply 2 exceeded load threshold too high power supply load change/verify unit too high power supply load change/verify unit Power Supply 1 partial internal power supply alarm /
availability partial power available Power Supply 2 partial internal power supply alarm /
availability partial power available change/verify unit change/verify unit High Power Consumption too high power supply load change/verify unit Low Power Consumption too low power supply load change/verify unit table 4-8 Status LED alarms M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 51 4.4. External Alarm Inputs 4. Commissioning With the external alarm inputs, it is possible to monitor the status of connected devices, e.g. a UPS, via software. All alarm inputs are normally high (5 V) without connection. The polarity (high/ low) can be set via the software at the Master Unit (for details please see the appropriate ION-U software manual). The device to be monitored must be connected so that the alarm contacts will be closed in case of an alarm (I max = 8 mA). The alarm inputs are potential-free with common ground (earth). Subminiature circular connectors series 712 with five contacts, which are contained in the alarm kit, can be ordered directly from the Binder Connector Group, the manufacturer, or indirectly from CommScope. 4.5. Troubleshooting The status of the Extension Unit can be checked via the Master Unit (for details please refer to the ION-U software manual). Locally, the status can be checked at the LED, see chapter 4.3.2. Page 52 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 5. Low Power EU Maintenance 5. Low Power EU Maintenance 5.1. General Read and observe chapter 1.2 Health and Safety. Note:
The Extension Unit does not require preventative maintenance measures. Maintenance of the ION-U Low Power units should be performed by replacing only components that are described in this chapter. In order to maintain the warranty, avoid unintentional damage to the seals on the modules. The spare parts list includes only units that can be replaced in the field without tuning or soldering work. Please contact your CommScope sales representative or DCCS Technical Support for a current ION-U LP EU parts list. Note: When sending back the unit, use appropriate packaging. Use of the original packaging for shipping the unit is strongly recommended. Note:
Note:
Defective parts should only be replaced by original parts from the supplier. All service work performed inside the housing is performed at the users own risk. Label any unlabeled cables before disconnecting them to ensure correct reconnection. For most maintenance procedures, appropriate tools are required to ensure correct handling. All of these tools can be ordered from the supplier. Note: All unit screws have a right-hand thread, and are tightened by turning the screws clockwise and loosened by turning them counter-clockwise with an appropriate tool. Due to the design of the Extension Unit, the power supply is the only component that should be replaced in the field. Please contact the supplier for replacement of any other components. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 53 5. Low Power EU Maintenance 5.2. EU Power Supply Replacement The power supply for the EU is a field replaceable module. The type of power supply used by the unit (AC, DC, or Vdc/100) is dependent on the model number. Attention: Before starting any maintenance on the EU, read and observe chapter 1.2 Health and Safety and the electrical installation information in chapter 4.2.1 Health and Safety for electrical installation. 1. Danger: Electrical hazard. Danger of death or fatal injury from electrical current inside the unit in operation. Before opening the unit, disconnect mains power. 2. Caution: The unit reaches high temperature in operation. Risk of burns by hot surface. Do not touch the unit before it has sufficiently cooled down. 1. Switch off the circuit breaker supplying power to the EU. 2. Once you have confirmed that the power has been shut down, remove power connector from the unit. Mains Mains plug 3. Locate the power supply on the right side of the Extension Unit. figure 5-1 Disconnect mains power Power supply figure 5-2 EU power supply location Page 54 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 5. Low Power EU Maintenance 4. Use a #2 Phillips head or slotted screwdriver to loosen the 8 universal slot/Phillips captive power supply screws the and carefully remove supply. The weight of the power supply must be supported as you loosen the screws to prevent damage to the supply. 5. Carefully remove the power supply from the unit. Do not attempt to support the weight of the supply with the attached input and output cables. Loosen 8 universal slot/Phillips screws Mains connector figure 5-3 8 EU power supply screws figure 5-4 EU power supply with cables 6. Locate the cable connector for the power supply on the right side of the supply. input 7. Loosen the 3 Phillips head terminal screws and remove the connector. figure 5-5 EU power supply input cable M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 55 5. Low Power EU Maintenance 8. Locate the output connector for the power supply on the left side of the supply. 9. Loosen the 2 Phillips head screws and remove the output connector. figure 5-6 EU power supply output cable 10. Remove the defective supply. figure 5-7 EU with power supply removed 11. Replace the defective power supply with the new power supply. It is very important to confirm that the replacement supply is the same type as the original supply. The AC, DC, and Vdc/100 supplies are not interchangeable. 12. Reconnect the input and output connectors, and tighten the associated terminal screws. figure 5-8 EU with replacement power supply Page 56 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 5. Low Power EU Maintenance 13. Insert the power supply into the EU carefully to avoid damaging any cables. The supply must be supported until the 8 universal slot/Phillips captive power supply screws have been tightened. 14. Tighten the slot/Phillips supply screws. 8 universal captive power figure 5-9 EU insert power supply 15. Reconnect the Mains power plug. 16. Switch on the breaker and for proper the EU check operation. figure 5-10 Reconnect mains power M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 57 6. Appendix 6.1. Illustrations 6.1.1. Dimensions and Mounting 6. Appendix figure 6-1 ION-U Low Power EU mounting bracket figure 6-2 ION-U Low Power Unit dimensions Page 58 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 6. Appendix figure 6-3 Installation drawing of ION-U L Unit single figure 6-4 Installation drawing of ION-U L Unit dual M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 59 6.1.2. ION-U EU L Cable Kits 6. Appendix A cable kit is included with each ION-U Low Power Extension Unit as shown in table 6-1 below. One PSU cable (AC or DC version) is included with each Remote Unit. ION-U EU L Cable Kit Cable and Description PSU cable (Either AC or DC version depending on power supply type) 4.3-10-M to 4.3-10-M (equivalent cable loss of 0.141, outdoor rated) Qty 1 2 2 N-M to 4.3-10-F adapter 4 QMA-M to QMA-M (equivalent cable loss of 0.141, outdoor rated) 2 RS232 for modem communication RU-EU table 6-1 Extension Unit Cable kit Length 1.5 m 1.5 m 1.5 m 6.1.3. LP RU, EU L 25T/25T, and EU L 23/23 Ports Low Power Remote Unit A B C D E K J I H G F A Mains power connector G Pwr/Ctrl connector B Grounding (earthing) bolts H Alarm connector C RF antenna port D Probe E Local Port RS-232 F Status LED I Expansion UL port J Expansion DL port K Optical ports figure 6-5 LP RU connectors and Status LED Page 60 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 6. Appendix EU L 23/23 Extension Unit A B C D E F G H R Q P O M N I L K J A Expansion DL port path 2 J Grounding (earthing) bolts B Expansion UL port path 2 K RF antenna port 4-21 IN path 1 C Expansion DL port path 1 L RF antenna port 4-21 IN path 2 D Expansion UL port path 1 M RF antenna port OUT path 2 E Status LED path 2 F Status LED path 1 G Probe path 2 H Probe path 1 N RF antenna port OUT path 1 O Local Port RS-232 path 1 P Ctrl connector path 1 Q Local Port RS-232 path 2 I Mains power connector R Ctrl connector path 2 figure 6-6 EU L 23/23 connectors and Status LEDs M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 61 6. Appendix EU L 25T/25T Extension Unit B C D A E F G H I J K L S T U V R Q M P O N A Expansion DL RU port path 2 L Status LED path 1 B Expansion UL RU port path 2 M Mains power connector C Expansion DL EU port path 2 N Grounding (earthing) bolts D Expansion UL EU port path 2 O RF antenna port 4-23 IN1 path 1 E Expansion DL RU port path 1 P RF antenna port 4-23 IN2 path 2 F Expansion UL RU port path 1 Q ANT-1 RF antenna port OUT path 1 G Expansion DL EU port path 1 R ANT-2 RF antenna port OUT path 2 H Expansion UL EU port path 1 S CTRL connector path 2 I Status LED path 2 T Local Port RS-232 path 2 J Alarm connector path 2 U CTRL connector path 1 K Alarm connector path 1 V Local Port RS-232 path 1 figure 6-7 EU L 25T/25T connectors and Status LEDs Page 62 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 6. Appendix 6.2. Specifications This manual is valid for the following Extension Units:
ID No 7769134-xxxx 7769134-0001 7769134-0002 Denomination ION-U EU L 17EP/17EP ION-U EU L 17EP/17EP VAC ION-U EU L 17EP/17EP VDC/100
* The xxxx suffix is the identifier for the specific configuration of the Remote or Extension Unit. For ION-U Low Power Extension Unit specifications, please refer to the online CommScope Product Catalog at http://www.commscope.com/Product-Catalog/Wireless/Product/Distributed-Coverage-and-Capacity/
or contact Technical Support at https://www.CommScope.com/wisupport. 6.3. Spare Parts Maintenance of the RU should be performed on an FRU (Field Replaceable Unit) basis only. If any other part not contained in the following list needs to be replaced, please contact customer service for additional instructions. Designation:
Power Supply Unit Vac RPS150-Vac Power Supply Unit Vdc 100 RPS150-Vdc/100 Expansion port RF cable, 1.5 m 4.3-10 to 4.3-10 RF cable, 1.5 m RS232 cable, 1.5 m ID No 7658962-xx 7662384-xx F1A-PQMQM-1M5 F1A-HMHM-1M5-P 7702134-xx The manufacturer reserves the right to replace the spare parts listed above by equivalent substitutes. M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 63 7. List of Changes Version M0200AJA Changes Initial Release 7. List of Changes Release Date 02-May-2018 Page 64 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U 8. Index 8. Index A I Alarms Bite and Alarms ............................................... 50 External Inputs ................................................. 52 Status LED ....................................................... 51 Ant IN ................................................................... 37 Ant RF .................................................................. 37 B Block Diagram ION-U EU L 17EP/17EP .................................. 17 C Cable Kits ............................................................. 60 Commissioning General ............................................................ 23 CommScope ......................................................... 13 Compliance............................................................. 9 Connections Antenna ........................................................... 42 Power .............................................................. 39 Connectors EU Ctrl connector ............................................ 22 EU Mains connector ........................................ 22 Contact Addresses, Customer Support .......... 14, 15 Ctrl connector ....................................................... 37 D Declaration of Conformity (DoC) ........................... 13 E EU AC power cable .............................................. 39 EU DC power cable .............................................. 39 EU Power Supply Replacement ........................... 54 EU Vdc/100 power cable ...................................... 40 Expansion DL ....................................................... 37 Expansion ports .................................................... 48 Expansion UL ....................................................... 37 G Grounding (Earthing) ............................................ 38 Grounding Bolts .................................................... 37 H Health and Safety ................................................... 8 Illustrations ........................................................... 58 Installation Electrical .......................................................... 35 Mechanical ...................................................... 23 M Mains (Vac/Vdc) ................................................... 37 Mains (Vdc/100) ................................................... 37 Mains connector ................................................... 39 Maintenance ......................................................... 53 Mechanical installation Mounting bracket ............................................. 24 Threaded pins .................................................. 27 MIMO applications ................................................ 18 Mounting bracket To a pole .......................................................... 25 To a wall .......................................................... 24 P Ports Antenna Port OUT ..................................... 21, 22 Coupling Port ................................................... 22 EU L 17EP/17EP ............................................. 21 EU L 23/23 ....................................................... 61 EU L 25T/25T .................................................. 62 Expansion Ports............................................... 22 LP RU .............................................................. 60 RS-232 port ..................................................... 22 Property Damage Warnings ................................... 8 PWR/CTRL ........................................................... 37 R RS-232 ................................................................. 37 S SISO applications ................................................. 18 Spare Parts .................................................... 53, 63 Status ................................................................... 37 T Troubleshooting .................................................... 52 M0200AJA_ION-U_EU_L_17EP_17EP.docx Users Manual for ION-U Page 65
This product uses the FCC Data API but is not endorsed or certified by the FCC