submitted | available | document details (if available) | source link |
---|---|---|---|
Adobe PDF Library 15.0 |
various | User Manual - A8190B IN100 (V3) Bored | Users Manual | 2.26 MiB |
IN100 with Aperio Technology Cylindrical Lock Installation Instructions A8189B 07/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Table of Contents 1 2 3 4 5 6 7 8 Warning ...................................................................................3 General Description .................................................................4 Hardware Specifications .........................................................4 Electronic Specifications .........................................................4 Parts Breakdown .....................................................................5 Lock Installation ......................................................................7 Operational Check ................................................................19 Lock LED Indications ............................................................20 1 Changes or modifications to this device not expressly approved by ASSA ABLOY could void the users authority to operate the equipment. Warning FCC:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Industry Canada:
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numrique de la classe B rpond toutes les exigences de linterfrence canadienne causant des rglements dquipement. Lopration est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer linterfrence nocive, et (2) ce dispositif doit accepter nimporte quelle interfrence reue, y compris linterfrence qui peut causer lopration peu dsire. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas lintensit ncessaire ltablissement dune communication satisfaisante. Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings. To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components:
Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door. Leave components (reader and controller) protected in their respective anti-static bags until ready for installation Do not touch pins, leads or solder connections on the circuit boards
!
. i d e t i b h o r p s i y n a p m o C g n i r u t c a u n a M f t n e g r a S f o i i n o s s m r e p n e t t i r w s s e r p x e t u o h t i w t r a p n i r o l e o h w n i s n o i t c u d o r p e R
. d e v r e s e r s t h g i r l l A
. y n a p m o c p u o r G Y O L B A A S S A n a
, y n a p m o C g n i r u t c a u n a M f t n e g r a S
, 6 1 0 2 t h g i r y p o C 6 1
/
1 3
/
7 0 1-800-810-WIRE www.sargentlock.com A8189B 2 General Description The SARGENT IN100 mortise lock with Aperio Technology makes it easy and cost-effective to bring access control to more doors. It uses local wireless communication between the lock and an Aperio hub to connect to an access control system, eliminating the greatest cost and inconvenience of traditional access control the wiring at the door. The IN100 utilizes HID multiCLASS SE technology, it supports heightened identity security and multiple credentials, including mobile access. All technology features are supported by the physical security of SARGENT ANSI/BHMA Grade 1 hardware -
quality components that provide high security, performance and durability. 3 Hardware Specifications Complete lockset with on-board memory ADA compliant Easily retrofits existing (cylindrical lock) door preps Latch - 1/2 standard 3/4 throw fire-rated double doors (optional) (41- prefix) Deadlocking latch - Stainless steel, non handed Lock furnished for 1-3/4 doors. For other thicknesses, consult factory. ANSI/BHMA A156.25 Listed Grade 1 Compliant Outside lever controlled by contactless reader or mechanical cylinder May be used for indoor and exterior applications 4 Electronic Specifications Input Power: DC 9V, 1.5A (6 AA alkaline batteries) Optional hard-power 12VDC to 24VDC HID multiCLASS SE technology offers support for the following credentials:
High Frequency (13.56 MHz):
HID iCLASS HID iCLASS SE (SIO-enabled) HID iCLASS Seos HID MIFARE SE HID DESfire EV1 SE MIFARE Classic DESfire EV1 Low Frequency (125 kHz):
HID Prox NFC-enabled Mobile Phones Uses low-rate wireless personal area networks
(IEEE 802.15.4) Multiple time zone and holiday access scheduling First-in unlock or automatic unlock configuration, based on specified time schedule Uses AES 128-bit wireless encryption*
Privacy button
*For specific security information, please contact your local ASSA ABLOY Door Security Solutions sales consultant or call 800-810-WIRE.
!
To comply with Fire Listed doors, the batteries must be replaced with alkaline batteries only. Warning: SARGENT Mfg. Co. IN100 locksets utilizing a door position switch (DPS) are not rated for, or intended for use in life safety applications. 4 1-800-810-WIRE www.sargentlock.com A8189B Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock 5 Parts Breakdown 1 2 1 3 4 ITEM PART NUMBER/ORDER STRING 1 IN-100-EM0110G77-IP-B IN-100-EM0110G77-IP-W IN-100-EM0110G77-IP-MB-[xxx]*
IN-100-EM0110G77-IP-MW-[xxx]*
IN-100-EM0110G77-IPS-B IN-100-EM0110G77-IPS-W IN-100-EM0110G77-IPS-MB-[xxx]*
IN-100-EM0110G77-IPS-MW-[xxx]*
2 3 4 IN-EM04 N/A IN-EM02-B IN-EM02-W IN-EM02-MB-xxx*
IN-EM02-MW-xxx*
* Specify finish DESCRIPTION HID iCLASS, HID iCLASS SE (SIO-enabled), HID iCLASS Seos, HID MIFARE SE, HID DESfire EV1 SE, HID Prox, NFC-enabled mobile phones HID iCLASS, HID iCLASS SE (SIO-enabled), HID iCLASS Seos, HID MIFARE SE, HID DESfire EV1 SE, HID Prox, NFC-enabled mobile phones HID iCLASS, HID iCLASS SE (SIO-enabled), HID iCLASS Seos, HID MIFARE SE, HID DESfire EV1 SE, HID Prox, NFC-enabled mobile phones HID iCLASS, HID iCLASS SE (SIO-enabled), HID iCLASS Seos, HID MIFARE SE, HID DESfire EV1 SE, HID Prox, NFC-enabled mobile phones All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 Mounting plate assembly COLOR/TRIM Black White Black with metal trim White with metal trim Black White Black with metal trim White with metal trim AA battery (alkaline only) Inside Escutcheon Assembly with Privacy Button - Black Plastic Inside Escutcheon Assembly with Privacy Button - White Plastic Inside Escutcheon Assembly with Privacy Button - Black Plastic & Metal Trim Inside Escutcheon Assembly with Privacy Button - White Plastic & Metal Trim Black White Black with metal trim White with metal trim QTY 1 1 1 1 1 1 1 1 1 6 1 1-800-810-WIRE www.sargentlock.com A8189B 5 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock Parts Breakdown (Continued) 12 4 5 8*
7 11 10 9 6 5 4 3 2 1 PART NO./ORDER ITEM 1 2 3 4 5 STRING
---
10-0043
---
---
10-0792 10-3049 10-3452 10-3453 10-3454 10-3455 10-3456 10-0847 10-3192 10-2052 10-3048
---
52-5374 DESCRIPTION Outside Lever (Reference Catalog for Available Styles) Lever Retainer Key (In Screw Pack 10-2052) Cylinder Assembly (Reference Catalog for Available Cylinders) Rose (Reference Catalog for Available Styles) Spacer Bushing QTY. 1 1 1 2 2 Outside Rose Spring Assembly Lockbody Assembly 10G77 (Standard Cylinder) Lockbody - LFIC (Removable Core) Lockbody - SFIC Lockbody - Keso Lockbody - Medeco Keymark LFIC & Schlage Full Size Interchangeable Core Adapter Plate/Spacer (Only Included With 1-3/8 Thick Doors) Latch Assembly Screw Pack Inside Rose Spring Assembly Inside Lever (Reference Catalog for Available Styles) Door Position Switch Kit (SPDT) 1 1 2 1 2 1 1 1
*Adapter Plate/Spacer (10-0847) is only shipped with orders that specify 1-3/8 doors. 13 6 7**
8 9 10 11 12 13
**The IN100 10G77 cylindrical lock supports Escape Return functionality. Tools Required:
#2 Phillips screwdriver Flat head screwdriver Security allen wrench 6 1-800-810-WIRE www.sargentlock.com A8189B Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock 6 Lock Installation 1 Prepare Door A. Verify Hand and Bevel of Door Stand on outside of locked door when determining door hand. Fig. 1A LHRB Left Hand Reverse Bevel Hinges Left Open Outward RH Right Hand Hinges Right Open Inward RHRB Right Hand Reverse Bevel Hinges Right Open Outward LH Left Hand Hinges Left Open Inward B. Prepare Door Prior to installation, all holes must be free of burrs, debris and sharp edges. Prepare door according to appropriate template (see website www.intelligentopenings.com). Field Template: A8149 (ships with product) Door Manufacturers Template: 4712 Outside of Door Inside of Door Raceway for Power
(Optional) Cable Hole Raceway for Lockbody Harness Through-bolt Holes Through-bolt Holes External DPS holes Lever Handle Hole Cylindrical Pocket and Latch Holes Pre-drilled Tap Holes Fig. 1B Wood Door Preparation Raceway for Power
(Optional) Cable Hole Raceway for Lockbody Harness Through-bolt Holes 1-800-810-WIRE www.sargentlock.com A8189B 7 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock 2 Install Strike Install strike in the door frame (Fig. 2). Centerline of Latch Front and Strike
(2) #8-32 x 3/4"
Latch Screws Fig. 2 3 Install Latchbolt 1. Install latch with beveled bolt facing the strike. 2. Attach with two screws but DO NOT tighten completely at this time. See section 8 - Secure Lock to the Door. Inside of Door IMPORTANT: Latch bevel must match door bevel and deadlocking latch must stop on strike when door is closed. Strike Fig. 3B Deadlocking Latch 4 Install Door Position Switch (DPS) 1. Push wires through raceway toward lock prep. 2. Push DPS firmly into place by hand. Note: DO NOT TAP SWITCH WITH ANY TOOL. 3. Install magnet into door frame. Push firmly into place by hand. See A7983. 4. To connect DPS to lock controller per diagram, refer to the wiring in Step #10 (Page 15). DPS
(Door Position Switch) CAUTION: if DPS is not installed or is installed improperly, door status monitoring features will not function. 8 1-800-810-WIRE www.sargentlock.com A8189B Fig. 3A Inside of Door Fig. 4 Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock 5 Lock Adjustments A. Lock Preset:
Lockbody holes: 12 and 6 oclock (Fig. 5). The lock is shipped preset and does not require adjustment for 1-3/4 thick doors. Outside of Door Door thickness:
1-3/4 thick Preset Lock Fig. 5 NOTE: Adjusting for a thicker door requires removal of the outside lever, scalp and spacer bushing;
see the following sections. If preset lock does not require adjustment, proceed to Section 7 - Install Lock. 1-800-810-WIRE www.sargentlock.com A8189B 9 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock 6 Through-Bolt and Door Thickness Adjustment (If Required) A. Remove Outside Lever 1. Insert key, rotate 45 clockwise and hold. 2. Depress lever retainer with push pin tool (provided). 3. Pull lever outward. Outside of Door B. How To Change Cylinder (If Necessary) 1. With outside lever in hand, use standard pliers to pull out cylinder retainer. 2. Remove key and cylinder from lever. 3. Insert new cylinder. 4. Secure by pressing cylinder retainer flush with the lever. Fig. 6A Cylinder Retainer Cylinder Spacer Key Outside Lever Cylinder Fig. 6B Push Pin Tool Washers required for 30- prefix
(10 Line Lever) to accept Schlage cylinder
(no cylinder provided) 10 1-800-810-WIRE www.sargentlock.com A8189B Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock C. Through-Bolt and Door Thickness Adjustment 1. (If necessary) remove outside lever, scalp and spacer bushing (Fig. 6C). Spacer Bushing Scalp Outside Lever 2. Rotate mounting plate to either align with through-bolt holes in door, or adjust for proper door thickness (Fig. 6D). Refer to markings on through-bolt post (Fig. 6C Detail). Fig. 6C 1-3/4 Thick Doors 2 Thick Doors Fig. 6C Detail 3. Re-install spacer bushing to align with back of lever, scalp, and lever (Fig. 6D). Fig. 6D 1-800-810-WIRE www.sargentlock.com A8189B 11 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock 7 Install Lock 1. From outside of door feed lockbody harness into the lockbody hole (Fig. 7A). For metal door: Feed harness through inside of door (not shown). 2. Continue to feed harness into raceway (towards top of door), exiting raceway hole on inside of door (Fig. 7B). 3. Slide lockbody into cross-bore hole from outside of door. 4. Lockbody must engage both the latch unit prongs and tail piece (Fig. 7C). IMPORTANT:
Door must remain open during installation (use door stop) Lockbody must be centered in the door Tuck excess wires into raceway to avoid pinching or damaging wires NOTE: Cable lengths exaggerated for illustrative purposes. Outside of Door Inside of Door Ground Ring Terminals Fig. 7A Fig. 7B Detail Fig. 7C Detail 12 1-800-810-WIRE www.sargentlock.com A8189B Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock 8 Secure Lock to the Door 1. Slide inside rose assembly and spacer bushing over lockbody. 2. Position ground lug between (top) #10-32x1-1/4 through-bolt and rose assembly (Fig. 8A). NOTE: Proper placement of ground wire (Fig. 8B) will prevent pinching/damage to the ground wire. Inside of Door 3. Secure rose assembly with (2) #10-32x1-1/4 through-bolts. 4. Secure latch by fully tightening (2) #6 x 3/4 self-tapping screws
(refer to previous section 3 - Install Latchbolt). NOTE: Cable lengths exaggerated for illustrative purposes. Ground Wire Fig. 8B Detail Fig. 8A 9 Assemble Inside Trim 1. Verify spacer bushing is inserted horizontally and aligned with lever (Fig. 9). 2. Place rose over shaft of lockbody against the surface of the door; hand-tighten, turning clockwise. 3. Attach lever. Push until engaged. Inside of Door Rose Fig. 9 Inside lever 1-800-810-WIRE www.sargentlock.com A8189B 13 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock 10 Outside Reader Installation 1. Orient the reader so the LED lens is at the top (Fig. 10A). 2. Feed the cable/connector through the door (from outside to inside). 3. Install the reader to the outside of door by aligning the mounting posts with the door preparation holes. Hold the reader flush against door while ensuring proper alignment. NOTE: Cable lengths exaggerated for illustrative purposes. Outside of Door LED Reader Assembly with Harness Fig. 10A 14 1-800-810-WIRE www.sargentlock.com A8189B Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock 10 Outside Reader Installation (Continued) 4. Feed the reader harness and DPS connectors through the inside mounting assembly
(and gasket if required*). See Figure 11B. IMPORTANT: Do not run wires through bottom flange hole in plate (Fig. 11B, C) - it will damage wires and the controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 11C). 5. Tuck excess cable into wire hole on inside of door. 6. Begin to secure the mounting assembly by partially tightening the (2) through-bolts on the inside of the door while ensuring proper alignment as you secure the reader (Fig. 11B). NOTE: Cable lengths exaggerated for illustrative purposes Gasket*
Mounting Plate Through-bolt Door Position Switch Reader Harness Through-bolt Lockbody Harness Ground Ring Terminal Fig. 10C Fig. 10B 6. Secure ground lug with #6-32 machine screw (Fig. 10C).
*Gasket is required for outdoor installations. Do not use gasket for fire-rated openings. If installing with gasket; separate gasket from mounting plate to feed cables/connectors through holes as indicated (Fig. 10B). Once cables/connectors are fed through, reattach gasket to mounting plate. 1-800-810-WIRE www.sargentlock.com A8189B 15 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock 10 Outside Reader Installation (Continued) Installation of Connectors CAUTION - Do not touch or allow debris to enter connector contacts. DPS (4-pin) A 9-24VDC Power*
Secure the following connectors to their respective terminals (Fig. 11D):
A. Secure the 4-pin DPS connector. B. Secure the 10-pin lock body assembly connector.
*NOTE: Optional 2-pin external 9-24VDC power connector. Ground Lug B IMPORTANT: Do not run wires through bottom hole in plate - it will damage wires and the controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 11B, D). C. When all connections have been made, tuck excess cable into wire hole on inside of door. Fig. 11D Lock Body
(10-pin) Secure Mounting Plate D. Secure the mounting assembly while ensuring proper alignment of outside reader and tighten the (2) through-bolts on the inside of the door to secure the reader (Fig. 11E). E. Secure the 24-pin card reader connector (Fig. 11F). Fully tighten Fig. 11E Reader
(24-pin) D Board-to-Board Connector Fig. 11F 16 1-800-810-WIRE www.sargentlock.com A8189B Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock 11 Installation of Inside Component Assembly (Controller) 1. Insert top tabs of controller into slots on mounting plate (Fig. 12). 2. Ensure proper alignment of board-to-board connectors while pivoting bottom of controller toward door until tab on bottom snaps securely into place on mounting plate. CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller. Controller Fig. 12 1-800-810-WIRE www.sargentlock.com A8189B 17 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock 13 Battery Installation 1. Place (6) AA alkaline batteries in the compartment, being careful to align polarity properly (Fig. 12). 2. After batteries are installed, there is a slight delay; then red and green flash*, audible beep and lock motor will cycle.
*See Section 8 - LED Indications for more information AA Batteries (6) Fig. 12 14 Inside Cover Installation 1. Assemble cover by hooking top edge on inside mounting plate. 2. Carefully press bottom of cover toward door without pinching or damaging wires. 3. Secure cover utilizing security allen wrench (provided). Fig. 13 18 1-800-810-WIRE www.sargentlock.com A8189B Inside Cover Security Allen Screw Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock 7 Operational Check 1. Insert key into cylinder and rotate (Fig. 14A). There should be no friction against lock case, wire harness or any other obstructions. 2. Check that the key retracts the latch. The key should rotate freely. 3. Try the inside lever; ensure it retracts latch. 4. Present a valid credential* (Fig. 14B) to unlock outside lever; turn lever handle to ensure latch retracts. Fig. 14A Note: The credential should approach the inscription on the reader as indicated (Fig. 14B) to ensure the credential is read properly. Do not wave credential. Fig. 14B 1-800-810-WIRE www.sargentlock.com A8189B 19 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock 8 LED Indications The communication hub has a single LED. It supports an optical scheme of red, green and yellow. The indication scheme is described by the figures below:
Communication Hub LED indications Figure 1. Communication hub normal operation LED indication 2 sec. Online Aperio lock offline EAC offline Aperio lock and EAC offline UHF communication Green Green + one red flash Green + two red flashes Green + three red flashes Yellow + off, fast flash Some special LED indication schemes are used during lock maintenance actions:
2 sec. Figure 2. Communication hub maintenance LED indication Pairing active Yellow + green Ethernet LED indication The LED on the AH40 communication hub indicates both the status of the Ethernet link level and ethernet communication:
2 sec. Figure 3. AH40 Communication hub Ethernet LED indication Ethernet link connected Ethernet communication Green Green +
off fast flash
*For more information, refer to Aperio Online Quick Installation Guide Document No: ST-001322-PF Date: 2015-12-23 20 1-800-810-WIRE www.sargentlock.com A8189B Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock Lock LED indications The lock has three LEDs. They support an optical scheme with red, yellow and green. The indication scheme is described by the figures below:
Figure 4. Lock normal operation LED indication Card + PIN access
(configurable) EAC response time Card access
(configurable) Access granted, EAC offline or online Access denied, EAC online Force closed in remote open/office mode Busy blink, com hub busy with other locks Access denied, EAC offline Lock mechanism is 1) blocked when closing Error in lock, maintenance required Tamper Time to replace the battery Battery reached end of life, lock disabled V3 USB cable detection action occurred Enter PIN One yellow flash after card, two flashes before PIN (.125 second) One yellow flash (.25 second) One green flash
(1 sec.) One red flash
(1 sec.) Five yellow flashes and one red flash (.25 second) Continuous yellow flashes
(.25 seconds every second) Three red flashes
(.5 second each) Continuous red flashes
(.125 seconds every 1 sec.) Ten red flashes (.125 sec. each)
(Repeated every 10 sec. if lock cant close) Ten red flashes (.125 sec. each) repeated every 10 sec. Continuous yellow flashes
(.25 seconds every 5 sec.) Continuous red flashes
(.25 seconds every 5 sec.) Five yellow flashes
(.25 second each) 1) When the lock mechanism is blocked (lock jammed) the lever must be turned to release the lock mechanism. Some special LED indication schemes are used during lock maintenance actions:
Figure 5. Lock hub normal operation LED indication Enter configuration mode Five yellow flashes
(.125 second each) 1-800-810-WIRE www.sargentlock.com A8189B 21 07/31/16Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.IN100 Cylindrical Lock Lock Self-Test LED indication After replacing batteries, a Power on Self Test (POST) is performed. The result is indicated using a series of red and green LED flashes as described by the figures below. LED indication after power up/replacement of the battery 8.3.1 Battery not fully charged Error in lock is an indication -10 quick (125ms) red blinks, that either new batteries are not at the right voltage or a backward battery has been installed; battery not fully charged; energy counter not reset or no Power on self-test done. Error in lock, maintenance required 8.3.2 Test pass Ten red flashes (.125 sec. each)
(Repeated every 10 sec. if lock cant close) 1 red (1s) + 1 green (1s), Power on self-test passed, see table below. Figure 6. Lock POST LED indication POST Successful One red, one green flash
(1 second) 8.3.3 Test fail 1 red (1s) + 3 blinks (500ms, green or red), at least one test failed (red), see table below. If a fatal error is detected the lock will enter an Error state and continuously indicating fatal error and will not read cards nor unlock. 1 sec 0.5 sec 0.5 sec 0.5 sec FATAL ERROR CABLE ERROR MECHANICAL ERROR FATAL ERROR CABLE ERROR MECHANICAL ERROR Tests core functionality. MCUs, memory and internal communication, etc. Tests communication between the different parts in the system, i.e. different boards connected with a wire. Test related to moving parts of the lock. 22 1-800-810-WIRE www.sargentlock.com A8189B Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.07/31/16IN100 Cylindrical Lock SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) www.sargentlock.comFounded in the early 1800s, SARGENT is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The companys customer base includes commercial construction, institutional, and industrial markets.Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience.A8189B - 07/16
This product uses the FCC Data API but is not endorsed or certified by the FCC