2.4GHz Transmitter with 3 in 1 receiver User Manual

FS-GT15 2.4GHz 3IN1 ELECTRONIC SYSTEM USERS GUIDE V1.0 DESCRIPTION FS-GT15 is a 3 in 1 multifunction 2.4GHz electronic system build for RC cars. It has built in servo and ESC inside the receiver all these features just in one small piece. SPECIFICATIONS Transmitter ModelFS-GT15 Tx Transmitter Frequency2.4G GFSK Remote control distance: >40m Power Supply4 Cell AA Batteries Configuration mode: button Receiver ModelFS-GT15 Rx Voltage Range1S Lipo Receiver frequency: 2.4G (GFSK) Supported motor: 180 brush motor, 180 carbon brush motor or 0716 hollow cup motor Supported servo: 5g or 9g 5-wire servo. FEATURES DESCRIPTIONS 2 channel transmitters, set ST TRIM and TH DR. Integration of Receiver, ESC and servo, high integration, install conveniently. Throttle neutral point adaptation without the TRIM setting of TH. Low voltage cut-off protection for battery / Throttle signal loss protection. Declarations and Warnings FS-GT15 Rx is a highly-integrated multifunction ESC. It has built-in functions of ESC, servo and 2-channel receiver. It must work with right motor and servo in order to get FS-GT15 Rx work properly, otherwise the FS-GT15 RX will be destroyed. Dont block the motor for a long time, which will damage the ESC. Dont block the servo for a long time, which will damage the servo driver. Transmitter WARNING: BATTERIES ARE SUITABLE FOR 4 ALKALINE BATTERIES. ENSURE THAT THE POSITIVE AND NEGATIVE POLES OF THE BATTERIES ARE INSTALLED CORRECTLY. THE INCORRECT POLARITY OF THE BATTERIES WILL CAUSE DAMAGE TO THE REMOTE CONTROL. LED INDICATES TRANSMITTER BATTERY VOLTAGE STATUS, WHEN ONLY ONE LED LAMP IS ON, THE BATTERY VOLTAGE IS LOW, PLEASE REPLACE THE BATTERY IN TIME!

Receiver Interface Battery Switch: Control the power of the receiver;

Battery interface: Battery interface for 1S Lipo;

Motor interface: The connector for 180 motor. Servo interface: The connector for 5-wire servo. Charging socketThe charging interface of the receiver. The receiver is charged by the transmitter. Warning: Ensure that the positive and negative poles of the battery interface are correct, and the inverse will burn out FS-GT15 RX. Transmitter and Receiver Pairing Please follow the following steps:

1. Open the receiver first and click the button to make the receiver enter the binding state. The LED will blink rapidly. 2. Turn on the transmitter. The transmitters red LED blinks quickly, indicating that the transmitter enters the binding state. The binding will be completed within 3s. 3. After binding successfully, the receivers LED will always be on. Receiver LED light State 1. LED light stays on: transmitter and receiver has been paired, work properly. 2. LED light blinks slowly: receiver does not pick a signal from transmitter: (1). transmitter is not on; (2). pairing has not been done yet. 3. LED light blinks once a second: battery voltage is low. 4. LED light blinks fast: under pairing mode. Fail Safe Fail safe feature build in receiver. When receiver stop communication with transmitter, ESC will stop outputting, then steering channel output will maintain the latest position. Low Voltage Protection The receiver has built-in low voltage protection. If the battery voltage is less than 3.3V, the receiver enters the low voltage protection mode and the motor output maximum speed is limited to 50%. If the battery voltage is less than 3.1V, the motor will stop running. Installation and Use Guide The remote control is a 2.4G wireless products, a proper installation and usage will exert influence on performance of the product. Due to the poor penetration of 2.4G signals, it is necessary to ensure that transmitters and receivers are used without occlusions in order to ensure reliable communication;

A build-in 2.4G signal receiving module inside the receiver, so keep it away as far as possible from other electronic products, motors, etc., to reduce interference;

The remote controller receiver and transmitter has an PCB antenna, keep any metal materials away near the antenna. As the radio frequency products are affected by the external environment, the performance differences vary greatly. The main points of installation and use are to ensure that the RF signals of the remote controller can be transmitted effectively and reliably. Proper installation and use are essential to ensure product performance. Summary: FS-GT15 Rx radio system is a high performance and multiple functions for RC cars. The built-in receiver and ESC make FS-GT15 Rx become a high degree of integration with complex functions product, please be sure to carefully read the user manual in using, avoid wiring error caused damage to the product. Transmitter troubleshooting Troubles After power on, no LED lights up Possible Causes Batteries are installed abnormal; Battery low Solutions Reinstall the batteries; change the batteries ESC troubleshooting Troubles Possible Causes Solutions After power on, No power is drawn to the Check the connections no LED lights up ESC; The switch is broken between battery and ESC; Re-

Led slowly blink The transmitter is closed solder the connector if neededChange the ESC switch Open the transmitterRe-pair The transmitter is not paired the transmitter Led blinks once a Battery voltage is low. Change battery. second The vehicle cant Incorrect TH D/R setting;

Increase TH D/R; Change reach to the full Battery protect due to battery battery speed. low The vehicle cant Battery low cut-off protect;

Change battery; Check the motion, but the The connection between ESC connection between the motor LED indicators and motor is interrupted; The and ESC; Change battery. work normally motor is damaged The motor accelerates The discharge capacity of the Change a battery with better battery is not strong enough;

discharge capability;

rapidly at the The motor rotates too fast, Use a motor with lower RPM, startup moment, and the gear ratio is too or smaller pinion to soften the but has lockout or aggressive; Something wrong gear ratio; Check the driveline cogging problem. with the driveline of the of the vehicle vehicle. FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.