| submitted | available | document details (if available) | source link |
|---|---|---|---|
| June 20 2016 | December 18 2016 | Adobe PDF Library 10.0.1 |
| various | User manual | Users Manual | 1.46 MiB | June 20 2016 / December 18 2016 |
ASUS Tablet User Guide E11431 First Edition / June 2016 Charging your device Ensure to fully charge your ASUS Tablet before using it in battery mode for extended periods. Remember that the power adapter charges your ASUS Tablet as long as it is plugged into an AC power source. Be aware that it takes much longer to charge the ASUS Tablet when it is in use. IMPORTANT! Do not leave the ASUS Tablet connected to the power supply once it is fully charged. ASUS Tablet is not designed to be left connected to the power supply for extended periods of time. Airplane precautions Contact your airline provider to learn about related in-flight services that can be used and restrictions that must be followed when using your ASUS Tablet in-flight. IMPORTANT! You can send your ASUS Tablet through x-ray machines (used on items placed on conveyor belts), but do not expose them to magnetic detectors and wands. Safety precautions This ASUS Tablet should only be used in environments with ambient temperatures between 0C to 35C (32F to 95F). Long time exposure to extremely high or low temperature may quickly deplete and shorten the battery life. To ensure the batterys optimal performance, ensure that it is exposed within the recommended environment temperature. Your ASUS Tablet Removing the MicroSD card tray To remove the tray, insert the pin into the hole beside the tray. Charging your ASUS Tablet Speaker/Headset port Front camera Ambient light sensor MicroSD card tray Touch screen panel Audio speakers Installing a microSD card USB Type-C port Microphone Rear camera Volume button Power button To charge your Tablet:
Connect the USB Type-C cable to the AC power adapter. Plug the AC power adapter to a grounded power outlet. Connect the USB Type-C cable to your ASUS Tablet. NOTE: The memory card slot supports microSD and microSDXC card formats. Charge your ASUS Tablet for eight (8) hours before using it in battery mode for the first time. IMPORTANT!
Use only the bundled power adapter and USB Type-C cable to charge your ASUS Tablet. Using a different power adapter may damage your ASUS Tablet. Peel the protective film off from the power adapter and USB Type-C cable before charging the ASUS Tablet to prevent risk or injury. Ensure that you plug the power adapter to the correct power outlet with the correct input rating. The output voltage of this adapter is DC 5V, 2A. When using your ASUS Tablet while plugged-in to a power outlet, the grounded power outlet must be near the unit and easily accessible. Do not use or expose your ASUS Tablet near liquids, rain, or moisture. Do not use your ASUS Tablet near heating equipment or in places where there is likelihood of high temperature. Keep your ASUS Tablet away from sharp objects. Do not place objects on top of your ASUS Tablet. NOTE:
Your ASUS Tablet can be charged via the USB port on the computer only when it is in sleep mode (screen off) or turned off. Charging through the USB port of a computer may take longer time to complete. If your computer does not provide enough power for charging your ASUS Tablet, charge your ASUS Tablet via the grounded power outlet instead. Appendices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by doing one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For FCC and IC e-labelling information, please go to Settings > About > Regulatory information. RF Exposure Information (SAR) This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT transmitting at the specified power level in different channels. The highest SAR value for the device as reported to the FCC is 1.01 W/kg when placed next to the body. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found at www.fcc.gov/general/fcc-id-search-page after searching on FCC ID: MSQP027. ZenTalk Fans Forum www.asus.com/zentalk/global_forward.php www.asus.com/support/
15060-78400000 Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003. This device complies with Industry Canada license-exempt RSS standard(s). This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The IC ID for this device is 3568A-P027. This device complies with Industry Canadas RSS-310. Operation is subject to the condition that this device must not cause harmful interference and must accept any interference, including interference that may cause undesired operation of the device. For FCC and IC e-labelling information, please go to Settings > About > Regulatory information. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has been evaluated for and shown compliant with the IC Specific Absorption Rate (SAR) limits when installed in specific host products operated in portable exposure conditions. Canadas REL (Radio Equipment List) can be found at the following web address:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng Additional Canadian information on RF exposure also can be found at the following web address:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html Canada, avis dIndustrie Canada (IC) Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lopration est soumise la condition que cet appareil ne provoque aucune interfrence nuisible. Cet appareil et son antenne ne doivent pas tre situs ou fonctionner en conjonction avec une autre antenne ou un autre metteur, exception faites des radios intgres qui ont t testes. La fonction de slection de lindicatif du pays est dsactive pour les produits commercialiss aux tats-
Unis et au Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer dinterfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement. Lidentifiant IC de cet appareil est 3568A-P027. Cet appareil est conforme la norme RSS-310 d'Industrie Canada. L'opration est soumise la condition que ce dispositif ne doit pas causer d'interfrences nuisibles et doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. Pour les informations dtiquette lectrique de FCC et IC, sil vous plat aller Paramtres > propos >
infos rglementaires. Informations concernant lexposition aux frquences radio (RF) La puissance de sortie mise par cet appareil sans fil est infrieure la limite dexposition aux frquences radio dIndustrie Canada (IC). tilisez lappareil sans fil de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a t valu et dmontr conforme aux limites SAR (Specific Absorption Rate Taux dabsorption spcifique) dIC lorsquil est install dans des produits htes particuliers qui fonctionnent dans des conditions dexposition des appareils portables.Ce priphrique est homologu pour lutilisation au Canada. Pour consulter lentre correspondant lappareil dans la liste dquipement radio (REL - Radio Equipment List) dIndustrie Canada rendez-vous sur:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng Pour des informations supplmentaires concernant lexposition aux RF au Canada rendez-vous sur:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html IC Warning Statement The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. The Country Code Selection feature is disabled for products marketed in the US/Canada. For product available in the USA/Canada markets, only channel 1-11 can be operated. Selection of other channels is not possible. This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528. Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated.
(v) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e.;
(iii) le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5725-5825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas.
(iv) les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, et nonce la section 6.2.2 3), doivent tre clairement indiqus.
(v) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-
5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. CE Mark Warning CE marking for devices with wireless LAN/Bluetooth This equipment complies with the requirements of Directive 1999/5/EC of the European Parliament and Commission from 9 March, 1999 governing Radio and Telecommunications Equipment and recognition of conformity. The highest CE SAR value for the device is 0.209 W/Kg. This equipment may be operated in:
AT EE IT NO BE ES IS PL BG FI LI PT CH FR LT RO CY GB LU SE CZ GR LV SI DE HU MT SK DK IE NL TR RF Exposure information (SAR) - CE This device meets the EU requirements (1999/5/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The limits are part of extensive recommendations for the protection of the general public. These recommendations have been developed and checked by independent scientific organizations through regular and thorough evaluations of scientific studies. The unit of measurement for the European Councils recommended limit for mobile devices is the Specific Absorption Rate (SAR), and the SAR limit is 2.0 W/
Kg averaged over 10 gram of body tissue. It meets the requirements of the International Commission on Non-Ionizing Radiation Protection (ICNIRP). For next-to-body operation, this device has been tested and meets the ICNRP exposure guidelines and the European Standard EN 50566 and EN 62209-2. SAR is measured with the device at a separation of 0 cm to the body while transmitting at the highest certified output power level in all frequency bands of the mobile device. A minimum separation distance of 0 cm must be maintained between the users body and the device, including the antenna during body-worn operation to comply with the RF exposure requirements in Europe. Prevention of Hearing Loss To prevent possible hearing damage, do not listen at high volume levels for long periods. Green ASUS notice ASUS is devoted to creating environment-friendly products and packaging to safeguard consumers health while minimizing the impact on the environment. The reduction of the number of the manual pages complies with the reduction of carbon emission. For the detailed user manual and related information, refer to the user manual included in the ASUS Tablet or visit the ASUS Support Site at https://www.asus.com/support/. Proper disposal Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. La batterie prsente un risque dincendie si celle-ci est remplace par une batterie de type incorrect. La batterie doit tre recycle de faon approprie. DO NOT throw the battery in municipal waste. The symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste. DO NOT throw the ASUS Tablet in municipal waste. This product has been designed to enable proper reuse of parts and recycling. The symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment and mercury-
containing button cell battery) should not be placed in municipal waste. Check local regulations for disposal of electronic products. DO NOT throw the ASUS Tablet in fire. DO NOT short circuit the contacts. DO NOT disassemble the ASUS Tablet. For France, headphones/earphones for this device are compliant with the sound pressure level requirement laid down in the applicable EN 50332-1:2013 and/or EN50332-2:2013 standard required by French Article L.5232-1. Limitation of Liability Circumstances may arise where because of a default on ASUS part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the listed contract price of each product. ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement. This limit also applies to ASUS suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible. UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY. Battery safety information 1. Do not disassemble or open, crush, bend, or deform, puncture, or shred. 2. Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse, or expose to water or other liquids, expose to fire, explosion or other hazard. 3. Only use the battery with a charging system that has been qualified with the system per CTIA Certification Requirements for Battery System Compliance to IEEE 1725. Use of an unqualified battery or charger may present a risk of fire, explosion, leakage, or other hazard. 4. 5. 6. 7. Promptly dispose of used batteries in accordance with local regulations. Avoid dropping the phone or battery. If the phone or battery is dropped, especially on a hard surface, and the user suspects damage, take it to a service center for inspection. Improper battery use may result on a fire, explosion, or other hand. For those host devices that utilize a USB port as a charging source, the host devices user manual shall include a statement that the phone shall only be connected to CTIA-certified adapters, products that bear the USB-IF logo or products that have completed the USB-IF compliance program. Rechargeable Battery Recycling Service in North America EC Declaration of Conformity This product is compliant with the regulations of the R&TTE Directive 1999/5/EC. The Declaration of Conformity can be downloaded from https://www.asus.com/support/. Power Safety Requirement Products with electrical current ratings up to 6A and weighing more than 3Kg must use approved power cords greater than or equal to: H05VV-F, 3G, 0.75 mm2 or H05VV-F, 2G, 0.75 mm2. Copyright Information No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translate into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (ASUS). ASUS and ASUS Tablet logo are trademarks of ASUSTek Computer Inc. Information in this document is subject to change without notice. Copyright 2016 ASUSTeK COMPUTER INC. All Rights Reserved. ASUS ZenPad 10 tablet is certified by ASUS under the name ASUS Pad P027. For US and Canada customers, you can call 1-800-822-8837 (toll-free) for recycling information of your ASUS products rechargeable batteries. Model name: P027 (Z500M) ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus. com/english/Takeback.htm for detailed recycling information in different regions. Coating notice IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the device except on the areas where the I/O ports are located. Regional notice for California WARNING! This product may contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Wash hands after handling. Manufacturer Address, City Authorized Representative in Europe Address, City Country ASUSTek COMPUTER INC. 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN ASUS COMPUTER GmbH HARKORT STR. 21-23, 40880 RATINGEN GERMANY EU Declaration of Conformity We, the undersigned, Manufacturer:
Address:
Authorized representative in Europe:
Address, City:
Country:
declare the following apparatus:
Product name :
Model name :
The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:
EMC Directive 2004/108/EC (until April 19th, 2016) and Directive 2014/30/EU (from April 20th, 2016) ASUSTeK COMPUTER INC. 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN ASUS COMPUTER GmbH HARKORT STR. 21-23, 40880 RATINGEN GERMANY ASUS Tablet P027 EN 55032:2012+AC:2013, Class B EN 61000-3-2:2014, Class A EN 55013:2001+A1:2003+A2:2006 R&TTE Directive 1999/5/EC EN 300 328 V1.9.1(2015-02) EN 300 440-1 V1.6.1(2010-08) EN 300 440-2 V1.4.1(2010-08) EN 301 511 V9.0.2(2003-03) EN 301 908-1 V6.2.1(2013-04) EN 301 908-2 V6.2.1(2013-10) EN 301 908-13 V6.2.1(2014-02) EN 301 893 V1.8.1(2015-03) EN 300 330-1 V1.8.1(2015-03) EN 300 330-2 V1.6.1(2015-03) EN 62209-2:2010 EN 62479:2010 EN 55024:2010 EN 61000-3-3:2013 EN 55020:2007+A11:2011 EN 301 489-1 V1.9.2(2011-09) EN 301 489-3 V1.6.1(2013-08) EN 301 489-4 V2.1.1(2013-12) EN 301 489-7 V1.3.1(2005-11) EN 301 489-9 V1.4.1(2007-11) EN 301 489-17 V2.2.1(2012-09) EN 301 489-24 V1.5.1(2010-09) EN 301 357-2 V1.4.1(2008-11) EN 302 291-2 V1.1.1(2005-07) EN 302 623 V1.1.1(2009-01) EN 50566:2013/AC:2014 EN 50385:2002 LVD Directive 2006/95/EC (until April 19th, 2016) and Directive 2014/35/EU (from April 20th, 2016) EN 60950-1: 2006 / A12: 2011 EN 60950-1: 2006 / A2: 2013 Ecodesign Directive 2009/125/EC Regulation (EC) No. 1275/2008 Regulation (EC) No. 642/2009 EN 60065:2002 / A12: 2011 Regulation (EC) No. 278/2009 Regulation (EU) No. 617/2013 RoHS Directive 2011/65/EU Ver. 160217 CE marking Equipment Class 2 Signature Jerry Shen Printed Name CEO Position
(EU conformity marking) Taipei, Taiwan Place of issue 30/6/2016 Date of issue 2016 Year CE marking was first affixed
This product uses the FCC Data API but is not endorsed or certified by the FCC