AprilBeacon N01 15 AprilBeacon N01-01 UserMan-US r1 Users Manual

 

AprilBeacon N01 Introdution AprilBeacon is one of the most commonly used beacons. Supporting both iBeacon and Eddystone. Battery level can be shown in the advertising data or via a Bluetooth GATT connection. While this beacon has both iOS and Android configuration apps, the iOS app is easier to use and is more functional. If you are setting up Eddystone-URL (for Android notifications) and you consider yourself to be non-technical then you will need use of an iOS device for setup. AprilBeacon N01 with acceleration sensor. Small size and replacable battery. Features Support both iBeacon and Eddystone Configurable including UUID, major, minor and TX power etc Upgrade Over-The-Air supported. Technical Details Power supply by CR2032 Battery 230~ mAh (replaceable). Dimensions: Height 33mm, Width 33mm, Depth 10mm Signal range 3m - 60m. Embedded acceleration sensor One LED and one button One hole for leash/strip Advertise 1st UUID when still, advertise 2nd UUID when move BLE micro controller NRF52810 Model Brand Type of Product Operating Supply Dimensions Wireless Specification Operating Frequency(RF) Type of modulation Channel Spacing RF Output Power (EIRP) Bandwidth Antenna Requirement AprilBeacon N01 April Brother Bluetooth Beacon CR2032 (3V DC) 33mm*33mm*10mm 2.402Ghz-2.480Ghz GFSK 2MHz 0dBm 2Mbps Antenna Gain Polarization 1.2dBi Horizontal polarization Default Settings Name Advertising Type Advertising Interval TX Power Proximity UUID Major Minor Parameters Sensor 700ms 0dBm B5B182C7-EAB1-4988-AA99-B5C1517008D9 1 Last 2 bytes of mac address Advertising Type Comparison Advertising Type iBeacon Eddystone Sensor Advertising Interval configurable configurable configurable Button press advertise UUID2 advertise UUID2 Acceleration Sensor Keep working Keep working Change button bit in advertising data Keep working Packet Format Advertising packet for sensor mode Byte(s) Name Value Notes 0 1 2 Flags[0]

0x02 Flags[1]

0x01 Flags[2]

0x06 See Bluetooth 4.0 Core Specification, Volume 3, Appendix C, 181. See Bluetooth 4.0 Core Specification, Volume 3, Appendix C, 181. See Bluetooth 4.0 Core Specification, Volume 3, Appendix C, 181. Byte(s) Name Value Notes 3 4 Length Type 5, 6 Service UUID 7 8 Length Type 9, 10 Service UUID 11, 12 Compoany ID 0x03 0x03 0x59, 0xFE 0x17 0x16 0x59, 0xFE 0xAB, 0x01 See Bluetooth 4.0 Core Specification See Bluetooth 4.0 Core Specification Service UUID for OTA service See Bluetooth 4.0 Core Specification Manufacturer Specification data Service UUID for OTA service ID for April Brother 13 Data Version 0x03

-

14 - 19 Mac Address 20, 21 Temperature

-

-

Reverse the order

-

22 23 24 25 26 27 28 29 30 Is Sensor Motion 0x00 When move the value = 0x01. when still the value = 0x00 X Acceleration Y Acceleration Z Acceleration Current Motion Duration Last Motion Duration

-

-

-

-

-

-

0x00 Current motion time in second 0x00 Last motion time in second Battery Level 0x64 Battery level in percent Measured Power Button State

-

-

-

pressed=0x01, idle=0x00 How to make the equipment start work Equipped with batteries or connected to power equipment which begin to work, start with Search and connected devices: (1) search AprilBeacon through shake assistant software;

(2) in the search list, select you to configure the Beacon, below we abeacon_3564, for example; (3) as shown in figure 2, click "abeacon_3564", enter the connection as shown in figure 3. Here is how to through the shake assistant software to configure and modify parameters Note: shake assistant before use, please open the mobile phone bluetooth, mobile phone android 4.3 system requirements, iOS 7.0, bluetooth 4.0;

1Open the bluetooth device, equipped with batteries;

2Open shake assistant (iOS download in the APP Store, the android APP Store download), iOS as for example in figure 1 below 3Search and connected devices: (1) search AprilBeacon through shake assistant software;

(2) in the search list, select you to configure the Beacon, below we abeacon_3564, for example; (3) as shown in figure 2, click "abeacon_3564", enter the connection as shown in figure 3. FIG.1 FIG.2 FIG.3 FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.