TRR11F Remote controller User Manual

Treadmill User Manual Manufacturer : Beijing Kingsmith Technology Co.,Ltd. Address : Floor 4, Building 25, Area 18, ABP Park, Fengtai, Beijing, China. After-sale service email : support@walkingpad.com Made in China Please read User Manual carefully before using this product ,and keep it well. User Manual User Manual WARNING IMPORTANT SAFETY INSTRUCTIONS Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for com-

pliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence. L exploitation est autorise aux deux conditions suivantes :

(1) l appareil ne doit pas produire de brouillage, et

(2) l utilisateur de l appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d en compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following mea-

sures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. FCC& IC Radiation Exposure Statement:

This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclaration d IC sur l exposition aux radiations:

Cet quipement est conforme aux limites d exposition aux radiations dfinies par le Canada pour des environnements non contrls. Cet metteur ne doit pas tre install au mme endroit ni utilis avec une autre antenne ou un autre metteur. DANGER To reduce the risk of electric shock: Always unplug this appliance from the electrical outlet immediately after using and before cleaning. WARNING To reduce the risk of burns, fire, electric shock, or injury to persons: 1) An appliance should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts. 2) Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons. 3) Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer. 4) Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair. 5) Do not carry this appliance by supply cord or use cord as a handle. 6) Keep the cord away from heated surfaces. 7) Never drop or insert any object into any opening. 8) Do not use outdoors. 9) Do not operate where aerosol (spray) products are being used or where oxygen is being administered. 10) To disconnect, turn all controls to the off position, then remove plug from outlet. Connect this appliance to a properly grounded outlet only. See Grounding Instructions. This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of expe-

rience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Keep children under the age of 13 away from this machine. User Manual To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. To reduce the risk of personal injury, read and understand all the instructions before using this product. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Content 01. Product and Accessories 02. Function Diagram 03. Instructions for Initial Operation 04. Learn to Use the Treadmill 05. Safety Notice 06. Maintenance and Service 07. Trademark and Legal Statement 08. After-sales Service and Warranty 02 03 07 09 13 16 17 18 Welcome to use our treadmill 01 Product and Accessories Thank you for choosing WalkingPad Smart Foldable Treadmill(hereinafter referred to as treadmill), which is featured with compact, simple and innovative overall design. With our treadmill, you can start your quality life at home. Please carefully check whether the contents of the package are complete and intact. If there is any missing or damaged, please contact the seller. Performance indicators Detailed parameters Applicable age 12-60 years old Speed range 1-9km/h

(6km/h max in Walking Mode) Running area 4401200mm Maximum load Rated voltage Rated frequency Gross weight Net weight 110kg 110-127V~

746W 35kg 32kg Working dimensions 14507501020mm Folding dimensions 990750160mm Sport mode Running mode / Walking mode Parts Other accessories Power Cable Remote Controller Lanyard Wrench 01 02 Safety lock Silicone Oil User Manual Main Product 02 Function Diagram 1. Walking Mode Mode button Display panel Power socket Wheel Power switch 03 2. Running Mode Phone holder socket Running belt Safety lock socket Handrail Handrail quick disassembling device Folding hinge Running belt adjusting hole Handrail lockup device Anti-skid side cover 04 02 Function Diagram 3. Functional introduction to display panel 4. Remote control Time Distance Speed Step Calorie The number of step and calorie should be set in APP so that they can be shown on display panel. FUNCTION Touch button ACCELERATION DECELERATION Standby Mode Manual Mode Automatic Mode 05 Wi-Fi indicator light Fault Warning Light LANYARD HOLE MODE BATTERY COVER THE FRONT THE BACK 06 03 Instructions for Initial Operation 1. Choose flat ground to place the treadmill. It is forbidden to place it on thick or soft cushion. 2. Unlock the handrail lockup device, lift the handrail until it s upright,and tighten the handrail lockup device. 5. #######

6. Insert safety lock into the safety lock socket and the phone holder into the phone holder socket.Connect the treadmill to power,and press the power switch. 3. Unfold the treadmill slowly and press it down to 4. Loosen the handrail quick disassembling device,adjust it completely flat. 07 to an appropriate height,and lock handrail quick disassembling device. 7. Download KS RECORD ,complete installation and registration. 8. Open the APP,bind the treadmill according to the prompts,and the treadmill is ready for use. 08 04 Learn to Use the Treadmill 1. Introduction to modes Standby Mode Light of the Standby mode is on;

Motor and sensor stop responding. Manual mode Light of the manual mode is on;

Control the speed through the remote control or APP. Automatic Mode Light of the automatic mode is on;

Speed is automatically controlled by intelligent algorithm. It follows the speed of walking. 2. Instructions of the standby mode control 3. Instructions of manual mode control (primary mode) Standby Mode In Standby Mode,user can short press the mode button on remote control to turn on the treadmill and enter Manual Mode by default.Or touch the standby icon on the display panel to turn on the treadmill. Manual Mode In this mode,you can control the treadmill by the remote control. It is recom-

mended that beginners use Manual Mode first and then use Automatic Mode,after being skilled in using the machine. In the manual mode, set as the intelligent start and st op, the Treadmill will start automatically to the target speed (default is 3 km/h ) while entering this area. ACCELERATION Short press: increase speed by 0.5 km/h FUNCTION Short press: tart or top the Treadmill DECELERATION Short press: reduce speed by 0.5 km/h 09 10 Under non-operating status,long press the mode button or touch the standby icon on the display panel,then the machine will enter Standby Mode. MODE Short press:mode switch Long press:switch to Standby Mode(non-operating status) 04 Learn to Use the Treadmill 4. Instructions of automatic mode control (advance mode) 5. Instructions of remote control pairing 7. Error indicator light Automatic mode This is a challenging and higher-class mode, you can operate the treadmill completely out of remote control. It s better to use Automatic Mode after being familiar with the machine. Function button and mode button can work in this mode. Entering this area, the Treadmill will start or accelerate under the automatic mode. Note:Automatic Mode is available only when the treadmill is in the walking mode. Entering this area, the Treadmill will slow down automatically under the automatic mode. If the remote control has no response or you ve changed a new one, the remote control and walk-

ing device need to re-establish communication. Pairing method:restart the machine,and keep pressing the mode button for 5s. 6. Wi-Fi indicator light Waiting for fast connection Slow flashing In network connection Fast flashing Successfully connecting Normally on to the router Successfully connecting No indicator to the cloud E01: Drive communication fault E02: Motor abnormalities. E05: Overcurrent protection E06: Motor protection. E08: Sensor fault. E09:Wi-Fi connection failure. 8. Networking and firmware upgrading Le aving the factor y,the trea dmill is at wait-

ing-for-connection status.User can bind it directly with APP. If it is needed to configure the network again,you can long press the standby button on the display board,until the treadmill comes out the sound of beep and the Wi-Fi indicator light starts to flash. Firmware upgrading:You may receive the updating prompt from your app.Please view the updating introduction,and operate on your mobile phone according to it to complete the firmware upgrada-

tion.During firmware upgrading,the display panel shows UPG. 11 12 05 Safety Notice Please keep a rear distance 2000 mm or more. Please keep a distance of 500 mm or more for both sides. Please choose sport shoes and suit. Unplug the power cord when the treadmill is not in use. Trampling the machine head is prohibited. Using machine with pet is prohibited. While using the treadmill,please clip the safety lock on the clothes .If any unexpected situation occurs,please pull out the safety lock, and the treadmill will immediately stop. Using on uneven ground is prohibited Walking sideways or backwards on the machine is prohibited. Please use it carefully for elders and pregnant women 13 14 05 Safety Notice 06 Maintenance and Service 1. Clean the treadmill Anti-pinch Beware of involving your things. Do not fold the treadmill with power-on. 2. Belt deviation and adjustment Turn off the machine and unplug the power cord. Wipe off dust and stains on the frame, front panel and belt. Do not wipe backside of the belt. After using for a period, dust and stains may appear on the back part, that is normal and just. clean them up. Start the treadmill,and keep the belt running at the speed of 3km/h. Running belt inclined left: Turn the left adjustment screw 1/4 circle clockwise. Running belt inclined right: Turn the right adjustment screw 1/4 circle clockwise. Slipping running belt: Turn the left and right adjustment screws clockwise at the same time a half circle. Run the running belt for a period of time (1~2 minutes) to observe the centering situation. If necessary, please adjust it again. Do not store the treadmill upright. Do not step up and down the treadmill with belt running. 3. Lubricate the Belt Turn off the machine and unplug the power cord. Lift up the belt and apply silicone oil on the backside of the belt. Power on the treadmill again to run the running belt at 3km/hr for 10-20 seconds. 5-10 ml of silicone oil is needed for one time of lubrication. Add the silicone oil every 3 months. 15 16 07 Trademark and Legal Statement 08 After-sales Service and Warranty Beijing Kingsmith Technology Co., Ltd has a number of patents covering the WalkingPad Smart Foldable Treadmill series. This manual is copyrighted by KINGSMITH, Inc. No organization or individual may copy or distribute all or any part of this manual without the written permission of KINGSMITH, or use these patents without permission. This manual contains as much as possible the function descriptions and instructions for use when printing. However, it may still be inconsistent with the product you purchased due to continuous improvement of product functions, design changes or other. The description in this manual may differ from the actual product in terms of color and appearance due to product updates. Please refer to the actual product. Applicable product standard:

ASTM-F2276 ASTM-F2276 UL1647 The after-sales service of WalkingPad Smart Foldable Treadmill products are covered in the Three Guarantees service in strict accordance with the Consumer Protection Law of the People's Republic of China and Product Quality Law of the People's Republic of China. The service content is as follows: the customer can enjoy the return, exchange and repair services free of charge during the term of the Three Guarantees, wherein the repair, exchange, return should be handled by invoice. The product can be returned without any reason within 7 days from the next date of receipt, but the user needs to bear the logistics costs; provided, however, for any performance failures listed in the WalkingPad Smart Foldable Treadmill Fault Table, the user can enjoy the following services free of charge after the fault is confirmed. Service Type Service Policy Return Exchange Repair Return due to product quality within 7 days from the next date of receipt of the goods Exchange due to product quality within 15 days from the next date of receipt of the goods Repair due to product quality within 365 days from the next date of receipt of the goods Friendly reminder: the packing box is required to ensure the safety of the product during transportation, so it is recommended to keep the packing box at least 30 days from the date of receipt. Non-warranty policy 1. Repair, misuse, collision, negligence, abuse, liquid injection, accident, alteration, improper use of non-product accessories, or tearing or altering the anti-counterfeiting marks. 2. Expiration of the validity period of three guarantees 3. Damage caused by force majeure. 4. Incompliance with the performance failures listed in the Fault Table of WalkingPad Smart Foldable Treadmill. 5. P er forman ce failure s of the prod uct and its accessories belonging to Fault Table of WalkingPad Smart Foldable Treadmill due to human reasons WalkingPad Smart Foldable Treadmill Name Performance failure WalkingPad Smart Foldable Treadmill The functions listed in the manual are invalid No response at boot Power on alarm 17 18