MSW-P-S-01 mySwing Professional Sensor Users Manual

STEP 1 MYSWING PROFESSIONAL INCLUDES:

STEP 2 IMPORTANT STEP 3 GETTING STARTED PART 1 STEP 3 GETTING STARTED PART 2 STEP 3 GETTING STARTED PART 3 STEP 4 THE SENSOR LEDS PART 1 STEP 4 THE SENSOR LEDS PART 2 STEP 5 CONNECT TO TABLET Keep Away From Magnetic Fields. Connect the straps to the sensor bases. Place the sensors into the bases. Attach shaft sensor just below the grip with charging contacts pointing down. Rotate the sensors 90 degrees counter-clockwise. Handle the sensors gently, do not over tighten. Align the shaft sensor parallel to the club face as shown. Case Keyboard Degausser 3 Feet Use the appropriate length of strap that ts the player for each segment. Attach the straps according to the diagram. Attach the appropriate label (e.g. forearm, thigh, etc.) to the straps, if desired. Parallel Charging Case Body Sensor 17 Shaft Sensor 2 Receiver Tablet Body Sensor Base 15 Shoulder Harness Transformer for Charging Case Shoulder Harness Velcro Straps 15 Antenna MySwing Pro sensors must always be kept at least 3 feet away from all magnetic

elds. Magnetizing a sensor will cause noticeable errors in the avatar. If this occurs repeatedly, contact Customer Service to have the sensor recalibrated or replaced. To turn on, hold the button for 2 seconds. To turn off, hold the button for 5 seconds. To reset sensor, turn on, then hold the button for 10 seconds.

( Sensor must be fully recharged after reset. ) LED Colors Green ( frequency 1 ) is the default.

( multiple systems in close proximity must use different frequencies ) frequency 1 frequency 2 frequency 3 frequency 4 frequency 5 charging, low battery, or sensor error LED Status Slow Blink Fast Blink Standby Working Double Blink every 3 seconds Sleep Mode Blinking Red LED Indicates Low Battery

( approximately 20 minutes remaining ) Constant Red Light outside of charging dock Sensor Error

( Reset Sensor ) Start mySwing Professional software. Add new student by clicking the plus button. Enter Students Information, Height, Wingspan, and Agree to the Terms of Use. Proceed to Screen/Swing Tab. Click on the Connect icon and follow the on-screen instructions. powered by STEP 6 CALIBRATION PART 1 STEP 6 CALIBRATION PART 2 STEP 7 AUTOMATIC FREQUENCY CHANGE

* only necessary if using multiple systems STEP 8 CHARGING THE SENSORS www.myswing.com Follow the on screen calibration procedure. Make sure antenna is facing player before proceeding. Advanced Calibration Quick Calibration T Pose Feet are straight and square to the target line, six inches apart. Hold arms horizontal in both directions. Upper arms aligned with the body. A Pose Feet remain in the same position with thumbs placed on the seams of the pants. S Pose Feet remain in the same position with arms extended, with slight knee bend. 7 Pose Feet are straight and square to target line, six inches apart. Arms extended in front of player. Upper arms parallel to each other. Upper arms parallel to the ground. T Pose Feet remain in same position. Hold arms horizontal in both directions. Upper arms aligned with the body. L Pose Feet remain in same position. Stand tall and straight. Upper arms as close to the body as possible. Forearms parallel to the ground. Palms facing each other and thumbs pointing up. LL Pose Feet remain in same position. Remain in L Pose posture. Rotate both forearms out 90 degrees (or as much as possible). Use the middle ngers as the axes of rotation. Click the channel button in the top right corner. Select the channel. Check sensors for correct LED color. If a sensors LED color is not correct, it must be changed manually. Gently place each sensor into the charging case. Close the charging case cover. Connect the transformer to the charging case, make sure all LEDs are constant red. When a sensor is fully charged, the red LED will turn off. Any Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Contact Support TOLL FREE Support Number 1-844-843-1270 or E-mail: support@myswing.com MySwing Golf, Inc. 16411 N. 90th St. Ste. 101 Scottsdale, AZ 85260 QUICK START GUIDE