PICOPRO Pico projector User Manual

Table of Contents 1. Safety Precautions FCC Compliance Information FCC Class Notice FCC Caution FCC RF Radiation Exposure Statement Industry Canada Statement CE Caution IEC-60825-1 Caution 2. Certifications 3. Environmentally Friendly Disposal and Recycling 4. Package Contents 5. Product Features 6. Identifying Parts 7. Connecting PicoPro a. Compatible Operating Systems b. Wired Connection c. Wireless Connection d. Switching Connection Mode 8. Making Adjustments a. Volume Adjustment b. Speaker / Earphone Usage c. Laser Alignment 9. Charging the PicoPro 10. Troubleshooting 11. Specifications 12. Warranty 1. Safety Precautions This product is not waterproof avoid using it near water or wet places. There is a risk of malfunction if product is used in places where sudden or extreme temperature changes occur. Applying excessive force or impact to this product may result in product damage, and will void warranty. Never attempt to disassemble or service this product yourself. Doing so can result in electrical shock and void warranty. This is a Class 3R Laser product. For your safety, do not stare directly into the laser source. Doing so could damage your eyes. FCC Compliance Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference to another device. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Class Notice This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur with special installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/TV technician. FCC Caution Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Statement This device complies with Industry Canada license- exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. CE Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. IEC-60825-1 Caution Use of control or adjustments or performances of procedures other than those specified here in may result in hazardous radiation exposure. 2. Certifications KC : MSIP-CMM-CLK-PICOPRO FCC ID : TCLPICOPRO CE1177 compliant RoHS IC No : 10211A-PICOPRO IEC-60825-1 : Class 3R Laser CLASS 3R LASER PRODUCT 3. Environmentally Friendly Disposal and Recycling To protect the environment, dispose this product separately from household waste once it has reached its end of life, or take it to your local electronic waste disposal center. Built-in Battery Battery Type Battery Operating Time Battery Capacity Charging the Battery Battery Charging Time Rechargeable Lithium-ion Polymer Battery Approx. 150 minutes (with continuous use) 3140 mAh @ 3.7V Use supplied USB power adapter to begin charging the battery. Battery status is indicated by four blue LED indicators while charging.

(4 LED : 100% / 3 LED : 75% / 2 LED : 50% / 1 LED : 25%) Approx. 270 minutes 4. Package Contents PicoPro User Manual Power Adapter HDMI/MHL cable Samsung microUSB Adapter Tripod Pouch 5. Product Features PicoPro is a laser-based pico projector that fits in your pocket for a superior portability. It allows you to project contents in your mobile devices onto any surface via HDMI connection or Miracast screen mirroring capability. 6. Identifying Parts Touch-sensitive Volume Down Touch-sensitive Volume Up Backlit Battery Indicator Light Speaker Reset Button FCC ID : TCLPICOPRO CE1177 KC : MSIP-CMM-CLK-PICOPRO IC : 10211A-PICOPRO Model : PicoPro DC : 5V 2A Celluon, Inc. Made in Korea 3.5mm Audio Out Battery Status Indicator Power Button Mode Switch Button CHARGE Micro USB port for charging MHL/HDMI cable input 7. Connecting PicoPro a. Compatible Operating Systems For HDMI Connection Miracast DLNA For Wireless Connection Any digital devices that support HDMI capability Android OS 4.2 or later Windows OS 8.1 or later Any OS that supports Screen Mirroring functionality Any digital devices that support DLNA protocol

* Using DLNA connection requires downloading DLNA streaming app from the App Store or Play Store. b. Wired Connection Using HDMI Connection :

Use plug-n-play connection for any digital/mobile device via HDMI connection. 1. Turn on PicoPro by pressing the power button for about 2-3 seconds. 2. Celluon logo will display upon power on. 3. After the logo, Preparing wireless connection To go to HDMI mode, press Mode Switch button screen will display. 4. Press and hold Mode Switch button located next to power button for 2~3 seconds to change to HDMI mode. 5. PicoPro is now in HDMI mode. 6. Locate MHL/HDMI port on the PicoPro and use supplied HDMI cable to connect to a device. 7. PicoPro will start mirroring contents from connected device.

* For Apple devices, please use additional Apple digital AV adapter to connect via HDMI cable.

* For Samsung devices, please use supplied Samsung adapter (5pin to 11pin converter) to connect to MHL/HDMI cable. c. Wireless Connection Using Miracast :

The Miracast capability is called different names on difference devices. (Samsung/Sony Screen Mirroring , HTC Media Output) Please find this capability in the settings app on the device. 1. Turn on PicoPro by pressing power button for 2-3 seconds. 2. Celluon logo will display upon power on. 3. After the logo, Preparing wireless connection To go to HDMI mode, press Mode Switch button screen will display. 4. After about 20-30 seconds, Ready to Connect screen for Miracast will display. 5. On a desired mobile device, find and select Screen Mirroring / Media Output. 6. Mobile device will search for nearby devices to connect. 7. When device discovers Celluon PicoPro, tab to connect. 8. Mobile device will say Connected and PicoPro will start mirroring display. Using DLNA :

* To connect to devices using DLNA capability, you must install a DLNA streaming app on your mobile device. Apps can be downloaded from AppStore/GooglePlay 1. Turn on PicoPro by pressing power button for 2-3 seconds. 2. Celluon logo will display upon power on. 3. After the logo, Preparing wireless connection To go to HDMI mode, press Mode Switch button screen will display. 4. After about 20-30 seconds, Ready to Connect screen for Miracast will display. (Default wireless connection mode is Miracast) 5. Lightly press Mode Switch button again to change to DLNA mode. 6. DLNA Ready to Connect screen will display upon completion of mode switch. 7. On a desired mobile device, go to WiFiseting, and connect to Celluon PicoPro. Use password 12345670 to connect. 8. When Wifi is successfully connected, open the installed DLNA streaming application on the mobile device. 9. Select desired content to display. 10. Select display location: Celluon PicoPro. 11. Mobile device will say Connected and PicoPro will start display selected media contents.

*** For DLNA connection with iOS devices:

1. Follow above steps 1-7. 2. Find AirPlay option on devices status bar. 3. Tab AirPlay and select Celluon AirPico for display location. 4. Select a photo/video/music to share through PicoPro. d. Switching Connection Mode PicoPro allows you to easily switch from wired connection mode to wireless mode, and vice versa From HDMI mode to Miracast mode 1. From HDMI mode, pressand hold Mode Switch button for about 2 seconds. 2. Celluon logo will display. 3. After the logo, Preparing wireless connection To go to HDMI mode, press Mode Switch button screen will display. 4. After about 20-30 seconds, Ready to Connect screen will display for Miracast connection, indicating that the mode is successfully switched. From Miracast mode to HDMI mode 1. From Miracast mode, pressand hold Mode Switch button for about 2 seconds. 2. Celluon logo will display shortly, and Please connect using HDMI cable or press Mode Switch button to change to wireless mode screen will display. 3. Use HDMI cable to connect device. 1. From Miracast mode, lightly press Mode Switch button. 2. Ready to Connect screen for DLNA mode will display. From Miracast mode to DLNA / DLNA mode to Miracast

** Booting up time make take up to 3 seconds. 8. Making Adjustments Volume Adjustment Volume is controlled directly from PicoPro. Locate touch volume control area on top of device. Adjust the volume by lightly touching on the + or pattern. Speaker / Earphone Usage Please connect a speaker or an earphone to the 3.5mm audio out jack. Laser Alignment When the images seem blurry and/or the colors appear skewed, please visit Celluon website at www.celluon.com/support.php 9. Charging the PicoPro Charging Time 4-5 hours Battery Status LED Indicator Wired Connection (HDMI/MHL) Wireless Connection (Miracast / DLNA) 3+ hrs 2.5+ hrs Operating Time Status 0% charged 25% charged 50% charged 75% charged 100% charged Description Volume control + & - sensors will blink to indicate low battery status First LED indicator remains solid. When charging at this stage, the second LED indicator will blink to indicate it is being charged. First two LED indicators remain solid. When charging at this stage, the third LED indicator will blink to indicate it is being charged. First three LED indicators remain solid. When charging at this stage, the fourth LED indicator will blink to indicate it is being charged. All four LED indicators will remain solid. 1. Locate micro USB port next to the battery status button. 2. Use the supplied AC adapter to charge the PicoAir thought the micro USB port. Please fully charge PicoPros internal battery before first use (approximately 3 to 5 hours). A low battery warning icon will show on the screen when the battery is low. Use the included power adapter to charge your PicoPro. If the battery is too low, PicoPro will automatically shut off. 10. Troubleshooting No signal when a device is connected via HDMI cable Mobile device cannot find Celluon PicoPro during Miracast connection search Cannot stream contents through DLNA application Please make sure the cables are inserted into the correct port. Please note that different devices require different gender/adapter to convert to micro HDMI compatible. Please make sure PicoPro is on Miracast mode. This may also be due to a particularly heavy wireless traffic. If this is the case, please reset the device by pressing the reset button on the back of device. Please make sure devices WiFi is properly connected to PicoPros WiFi. For DLNA connection, please make sure to connect using the password 12345670 It depends on each DLNA streaming app to project contents through PicoPro. For large media files, it may take some time to load and convert the video to correct format. Please check if the connected mobile device is on sleep mode. If the screen of the connected device goes black, the projected screen will go black as well. Note that if the volume control LED patterns are on, the PicoPro is powered on. Please make sure the volume level of the PicoPro and/or connected device is not in the mute status. Please make sure connected device has enough battery to play the video. If both devices have enough battery, this may be due to unstable WiFi connection. Please disconnect and reconnect the device. This may be due to the depletion of battery or high temperature of the product. If the product is left in a place where the enviornmental temperature is high (such as in a blanket or near heater), the power will turn off automatically in protection of fire hazard. Please cool the product and use it within specified operating temperature before turning it on again. If the product has been shut down due to the depletion of battery, please charge the device before turning it back on. Please reset the device by pressing the reset button on the back of device. (Refer to Identifying Parts section for the location of reset button.) Please contact Celluon Customer Service for further assistance This is due to the shifts in laser diode. Please refer to Laser Alignment instruction page to adjust shifted lasers. This is due to the noise occurred by double wireless connection. Try to connect again after disconnecting all the previously connected wireless networks. It takes a long time to display contents through DLNA mode PicoPro is connected, but only the black screen is projected from the device There is no sound The video stops playing periodically Device automatically shuts down during use PicoPro is frozen; it stopped playing the video /

no response from buttons when pressed /

cannot convert modes Product makes abnormal noises The projected image is unclear Connection through Miracast intermittently disconnects during use 11. Specifications Item Product Lifetime Brightness Focus Max. Image (Screen) Size Sequential Contrast Ratio Resolution Aspect ratio Throw Ratio Color Depth Size Weight Battery Operation Time Speaker Audio Interface Wireless Classification Operating Temperature Wired Connection Android/Windows OS iOS Wireless Connection Android/Windows OS iOS Display Performance Measurement Electrical Characteristics Laser Safety Environmental Condition Compatibility 12. Warranty Spec. Laser 10,000 hours 30 ANSI lumens Infinite Focus (always in focus) 250 inches 80,000 : 1 1920 x 720p 16:9 1.1 1.67M colors (R/G/B 24bit) 150 x 73 x 13.4 mm

(6 x 3 x 0.5 inches) 181g

( 0.4lbs ) Wireless Connection: 2+ hrs Wired Connection: up to 3 hrs 1.0 W 3.5mm ear phone jack Dual (2.4G, 5G) IEC Class 2, Edition 3 0C - 35C Micro HDMI/MHL cable Micro HDMI Miracast DLNA Remark The perceived brightness of laser projectors with a given ANSI brightness is 50%+

higher than that of the LED based projectors No focus wheel required In optimal lighting conditions HD resolution Big screen at a short distance The operating time may vary depending on the environment of use Consumer safe device Additional Apple Lightning Digital AV Adapter required Screen Mirroring Download of DLNA streaming application required for DLNA connection Celluon warrants this product to be free from defects in materials and workmanship under normal use for a period of one (1) year from the date of purchase, as evidenced by the receipt of purchase. During the warranty period, Celluon shall repair or replace the product if defective. If replaced, the replacement shall be with a product of equal or greater value. This warranty is limited to the purchaser and is not transferable. Please contact support@celluon.com for warranty supports.