CWA2000 Wireless Motion Alert User Manual

Model CWA2000 Wireless Motion Alert To prevent possible SERIOUS INJURY or DEATH from electrocution, outputs are suitable ONLY for controlling low voltage devices, 24V max, ac or dc. Batteries: The AA batteries (not provided) in the base station should last up to one month. If the base station batteries are low, it will beep every few minutes. The AA batteries (not included) in the PIR motion sensor will last up to 2 years depending on use (lithium batteries are recommended for colder environments). For peak performance, inspect batteries annually and replace as needed. Programming Additional PIR Motion Sensors: The Base Station can learn the code of up to 3 additional PIR Motion Sensors, responding with unique buzzes. To program additional PIR Motion Sensors see Step 6. To order additional PIR Motion Sensors call 1-800-528-9131. Clear Memory: Press and hold the Learn Button on the Base Station until 3 beeps are heard. Overview The Wireless Motion Alert uses a Passive Infra-Red

(PIR) sensor to detect movement of people and vehicles, while allowing small animals to pass through undetected. The base station can be powered by 4 AA batteries for hours of continuous, wire-free operation or plugged in using the AC adapter. Carton Inventory Swivel Bushing Base Station Passive Infra-Red (PIR) Motion Sensor Rubber Pads Sun/Rain Shield Mounting Plate AC Adapter Operation & Features Base Station Antenna On/Off Button Volume On/Off: To turn the base station on and off, hold down the power button until you hear the on/off tone. Volume: The base station is equipped with adjustable volume controls. The lowest volume setting is the mute feature. 1 PIR Motion Sensor Assembly

& Test Step 1 Step 3 Attach PIR Motion Sensor box to mounting plate with large silver screw. Tighten screw until PIR Motion Sensor stays in place when repositioned. Step 2 Insert battery pack facing away from circuit board and attach cover. NOTE: Ensure the batteries do not touch the circuit board and the antenna and battery wires are not pinched. Step 4 Test PIR Motion Sensor by waving hand in front of sensor. Test light should flash. Secure cover with the smallest screws. Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) Test light will flash. Switch Settings Antenna PIR Sensor Switch #1 Switch #2 Test Button Switch #1:. OFF ON 15' Detection Range 30' Detection Range

(Default) Switch #2:

OFF ON Low Sensitivity High Sensitivity

(Default) OFF 1 2 ON NOTE: To avoid unwanted detection of small animals move Switch #2 to OFF. 2 Programming PIR Motion Sensor to Base Station Step 5 AC Adapter Input PIR Motion Sensor Installation Step 7 Mount PIR Motion Sensor horizontally on solid surface a few feet off the ground and within 1/2 mile of Base Station (rotate sensor to access screw holes). Unit should be able to swivel as needed. Attach sun/rain shield. NOTE: Keep PIR Motion Sensor antenna away from metal objects. Do not mount PIR Motion Sensor in direct sunlight, near moving tree branches, or in the path of a sprinkler system. Vehicle Alert Installation: For cars, the best mounting position is about 4' high, between 10-20'

back, and angled to see the back of car after passing the sensor. 10' - 20'

3' - 5'

Plug in Base Station. Adhere rubber pads to the bottom of the base. 4 AA batteries (not provided) are optional in case of a power failure. OPTIONAL A B Step 6 A Learn Button B A Ensure Base Station and PIR Motion Sensor are in close proximity to each other. Press and release learn button on Base Station. Buzzer will sound. B Within 5 seconds, wave hand in front of PIR Motion Sensor. Test light will illuminate and Base Station will buzz. 3 Troubleshooting The PIR Motion Sensor lights up, but the Base Station does not respond. The PIR Motion Sensor must be programmed to Base Station (See Step 6). Ensure Base Station is on and is not muted. If the green power light is not lit or is flashing, press the Mute Button on the top of the Base Station to wake it up. If the green power is illuminated, look at the two small white Base Station switches next to the Learn Button. The #1 Dip Switch should be down, towards the circuit board. If it is up, the Base Station has been muted. If the Base Station signals when you press the Learn Button, it is not muted. The Alert is not getting expected transmission range. Keep both antennas vertical and keep PIR Motion Sensor antenna away from trees and metal objects. Ensure Base Station is in clearest possible sight of the PIR Motion Sensor. The less objects between the devices, the longer the range. PIR Motion Sensor is detecting motion only part of the time. To detect cars, it is best to mount PIR Motion Sensor at height of cars motor and have it between ten and twenty feet from the road. Swivel sensor as needed. The Alert is giving false alarms. Check for moving tree branches or insects in sensor window. PIR sensor can also be triggered by light shining directly in sensor window, such as reflected sunlight, or motion in front of a light source. It is possible that condensation has built up on the sensor. Wipe condensation from PIR Motion Sensor with cotton swab. Let it sit inside for a few hours, open to the air, without the batteries and it should correct itself. Check Sensor Switches on PIR Motion Sensor. See Switch Settings. Base Station beeps every ten minutes. The battery in the Base Station is low. Replace with 4 AA batteries or operate it using AC Adapter. NOTE: Output switching capacity is low voltage

(24V max, ac or dc). NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:

1-800-528-9131 www.chamberlain-DIY.com NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 114A3896 2008, The Chamberlain Group Inc. All Rights Reserved