ZV-600 Bluetooth headset user manual

Hands Free While youre listening to your music, you can control your Bluetooth device with the below action on your ZV-600 ear phones Functions Operation Volume up Short press +button Volume down Short press button Last song Long press +button Next song Long press button Pause Play Short press MFB once Short press MFB once Specifications Bluetooth version: CSR8635|V4.0+EDR Bluetooth proles: HSP, HFP, A2DP, AVRCP Operating distance: 10M Talk time: 4-6 hours Standby time: 150 hours Charging time: about 1.5 hours Charging Port: Micro USB Charging ZV-600 comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the rst time. 1. Plug another side of cable to the USB port of PC or into a USB power charger

- Red light on: Charging

- Red light o: Finish charging 2.It will takes about 1.5 hours to nish charging 4 5 ZV-600 Connecting Hands Free Product Overview 1 2 6 3 4 5 Microphone Volume+/Previous song Indicator light Multi-Function Buttons Volume-/Next song USB charging port Turning On | Off Turning on:

Turning off:

Press and hold MFB for 4 seconds until blue LED ashes Press and hold MFB button about 4 seconds until red LED ashes 1) Keep your Bluetooth device within 1 meter when pairing;

2) Make ZV-600 enter pairing mode as shown:

Ensure ZV-600 is o. Press and hold Multi-Function Button for approximately 8 seconds until red and blue LED ash rapidly ;

3) Using your Bluetooth device, please scan/ search for available Bluetooth devices select ZV-600 from the list of devices shown;

4) If prompted, enter password or PIN No: 0000 5) If prompted by your mobile phone to connect, select Yes(this will vary among mobile phone models) 6) After successful connecting, blue LED of headset will ashes twice every 4 seconds Multi-pairing ZV-600 can connect with two Bluetooth cell phones at the same time. The general pairing procedures are as follows:

1Pairing ZV-600 with device A 2Turn on ZV-600 and make it enter pairing mode again, and pairing it with device B 3Operate device A to connect with headset. ZV-600 has already connected with two devices in this moment ZV-600 built-in microphone allows you to answer and end calls. Please use the chart below to execute your desired function. Functions Cancel a call Answer a call Short press MFB once Short press MFB once Operation Reject a call End a call Redial the last number Call transfer

(headset to phone) Call transfer

(phone to headset) Microphone mute Long press MFB about 2 seconds until you hear a tone Short press MFB once Double click MFB Press and hold MFB for 2 seconds Press and hold MFB for 2 seconds Double click MFB Cancel mute Double click MFB 1 2 3 FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.