| submitted | available | document details (if available) | source link |
|---|---|---|---|
| November 07 2012 | December 07 2012 | Microsoft Word - DIR-524_Manual.doc Administrator Acrobat Distiller 7.0.5 (Windows) |
| various | DIR-524 User Manual REV1 | Users Manual | 4.35 MiB | November 07 2012 / December 07 2012 |
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date 1.0 August, 2010 Description Updated for revision Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies. Copyright 2009 by D-Link Systems, Inc. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc. D-Link DIR-524 User Manual Table of Contents Package Contents..1 System Requirements...1 Features..2 Hardware Overview...3 Connections..3 Hardware Overview...4 LEDs...4 Installation5 Before you Begin..5 Wireless Installation Considerations6 Network Diagram....7 Connect to Cable/DSL/Satellite Modem.8 Connect to Another Router9 Getting Started...11 Configuration.....12 Web-based Configuration Utility.1 Internet Connection Setup Wizard..13 Manual Configuration.19 Static IP..19 Dynamic IP (DHCP)..1 PPPoE (username/password).1 Wireless Basic Settings..22 Wireless Security Settings..23 WDS Setting.....25 Network Settings..26 Advanced configuration..27 Port Forwarding.27 Application Rules...28 Access Control..29 Website Filters......30 Firewall Settings31 Advanced Wireless Settings32 D-Link DIR-524 User Manual Wireless MAC Filter..33 Advanced Network34 Static Routing.35 tools...36 Administrator Settings..36 Time Settings.37 System38 Firmware39 DDNS..40 PING TEST41 LOG SETTINGS42 Status43 Device Information43 LOGS.................................................................44 Traffic Statistics..45 Wireless..46 Support...47 Wireless Security.48 What is WPA?...............................................48 Configure WPA-Personal (PSK).....49 Connect to a Wireless Network....1 Using Windows Vista.50 Configure WPA/WPA2..51 Using Windows XP......53 Troubleshooting...54 Wireless Basics...58 Wireless Modes.62 Networking Basics......63 Technical Specifications.65 D-Link DIR-524 User Manual Section 1 Product Overview Package Contents D-Link DIR-524 Wireless Router Power Adapter Ethernet Cable Manual and Warranty on CD Note: Using a power supply with a different voltage rating than the one included with the DIR-524 will cause damage and void the warranty for this product. The product must be used with the power adapter included with the device. Note: Always attach the power cord plug to the power supply, before inserting the power cord and connected power supply to the wall outlet. System Requirements Ethernet-based Cable or DSL Modem Computers with Windows , Macintosh , or Linux-based operating systems with an installed Ethernet adapter Internet Explorer 6 or Firefox 2.0 or above (for coniguration) D-Link DIR-524 User Manual 1 Section 1 Product Overview Features Faster Wireless Networking - The DIR-524 provides up to 150Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. Compatible with 802.11g Devices - The DIR-524 is still fully compatible with the IEEE 802.11g standard, so it can connect with existing 802.11g PCI, USB and Cardbus adapters. Advanced Firewall Features - The Web-based user interface displays a number of advanced network management features including:
Content Filtering - Easily applied content filtering based on MAC Address, URL, and/or Domain Name. Filter Scheduling - These filters can be scheduled to be active on certain days or for a duration of hours or minutes. Secure Multiple/Concurrent Sessions - The DIR-524 can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-524 can securely access corporate networks. User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-524 lets you control what information is accessible to those on the wireless network, whether from the Internet or from your companys server. Configure your router to your specific settings within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range. D-Link DIR-524 User Manual 2 Section 1 Product Overview Hardware Overview Connections D-Link DIR-524 User Manual 3 Section 1 Product Overview Hardware Overview LEDs D-Link DIR-524 User Manual 4 Section 3 Configuration Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Before you Begin Please configure the router with the computer that was last connected directly to your modem. You can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet). If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet. When running the Setup Wizard from the D-Link CD, make sure the computer you are running the CD from is connected to the Internet and online or the wizard will not work. If you have disconnected any hardware, re-connect your computer back to the modem and make sure you are online. D-Link DIR-524 User Manual 5 Section 3 Configuration Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling can reduce your adapters range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized. 2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. 3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range. Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal. 4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise. 5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use. D-Link DIR-524 User Manual 6 Section 3 Configuration Network Diagram D-Link DIR-524 User Manual 7 Section 3 Configuration Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modems power adapter. Shut down your computer. Internet port on the router. 3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the 4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your computer. boot. 5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds). 6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router to 7. Turn on your computer. 8. Verify the link lights on the router. The power light, Internet light, and the LAN light (the port that your computer is plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable connections are correct. 9. Skip to page 15 to configure your router. D-Link DIR-524 User Manual 8 Section 3 Configuration Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network:
Disable UPnP Disable DHCP Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below:
1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Web-based Configuration Utility section for more information. If you need to change the settings, write down your existing settings before making any changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer. 2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to admin and leave the password box empty. Click OK to continue. 3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings to continue. Settings to continue. 4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server server checkbox. Click Save 5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change your computers IP settings back to the original values as in Step 1. 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. D-Link DIR-524 User Manual 9 Section 3 Configuration 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet port of the D-Link router. 8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and Wireless Security sections for more information on setting up your wireless network. D-Link DIR-524 User Manual 10 Section 3 Configuration Getting Started The DIR-524 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. You may manually configure your router without the wizard. Refer to the next page to manually setup your router. Insert the Quick Router Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows XP or Vista . The steps and screens are similar for the other Windows operating systems. If the CD autorun function does not automatically start on your computer, go to Start > Run. In the run box type D:\DIR524.exe (where D: represents the drive letter of your CD-ROM drive). When the autorun screen appears, click Wizard and follow the on-screen instructions. Note: It is recommended to write down the login password on the provided CD holder. D-Link DIR-524 User Manual 11 Section 3 Configuration This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Configuration Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). Select admin from the drop-down menu and then enter your password. Leave the password blank by default. If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance. D-Link DIR-524 User Manual 12 Section 3 Configuration Internet Connection Setup Wizard Once logged into the web interface of the router, the WELCOME TO THE WIZARD page will appear. Click the Wizard button to quickly configure your router using the setup wizard. If you want to enter your settings without running the wizard, click Manual and skip to page 23. Click Next to continue. D-Link DIR-524 User Manual 13 Section 3 Configuration Select the Static IP Address Connection and then click Next to continue. Fill in you IP information provided by you Internet Service Provider and then click Next to continue. Set the Wireless Network Name(SSID) and then click Next to continue. D-Link DIR-524 User Manual 14 Section 3 Configuration Select the Security Mode and then click Next to continue. Click Save to Save your configuration. Select the DHCP Connection (Dynamic IP Address) and then click Next to continue. D-Link DIR-524 User Manual 15 Section 3 Configuration If you selected DHCP Connection (Dynamic IP Address) , you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone MAC Address and then click Next to continue. The Host Name is optional but may be required by some ISPs. The default host name is DIR-524. Set the Wireless Network Name(SSID) and then click Next to continue. Select the Security Mode and then click Next to continue. D-Link DIR-524 User Manual 16 Section 3 Configuration Click Save to Save your configuration. Select the Username/Password Connection(PPPoE) and then click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. If you selected PPPoE, enter your PPPoE username and password. Click Next to continue. D-Link DIR-524 User Manual 17 Section 3 Configuration Set the Wireless Network Name(SSID) and then click Next to continue. Select the Security Mode and then click Next to continue. Click Save to Save your configuration. D-Link DIR-524 User Manual 18 Section 3 Configuration Manual Configuration Static IP Select Static IP Address if all the Internet ports IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format. IP Address:
Subnet Mask:
Default Gateway Address:
MTU:
MAC Address:
Primary DNS Address:
Enter the IP address assigned by your ISP. Enter the Subnet Mask assigned by your ISP. Enter the Gateway assigned by your ISP. Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU. The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. Enter the DNS address assigned by your ISP. D-Link DIR-524 User Manual 19 Section 3 Configuration Dynamic IP (DHCP) Use Dynamic IP(DHCP) if your Internet Service Provider (ISP) didn't provide you with IP Address information and/or a username and password. My Internet Connection:
Host Name:
MTU:
Select Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services. The Host Name is optional but may be required by some ISPs. Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU. MAC Address: The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. D-Link DIR-524 User Manual 20 Section 3 Configuration PPPoE (username/password) Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. PPPoE UserName:
PPPoE Password:
PPPoE Service Name:
Idle Time:
Enter your PPPoE user name. Enter your PPPoE password and then retype the password in the next box. Enter the ISP Service Name (optional). Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect. MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default MTU. MAC Address: The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. D-Link DIR-524 User Manual 21 Section 3 Configuration Wireless Basic Settings Use this section to configure the wireless settings for your D-Link Router. Please note that changes made on this section may also need to be duplicated on your Wireless Client. Enable Wireless:
Select Enabled to enable the wireless function. If you do not want to use wireless, select Disabled. for to customize the channel setting Service Set Identifier (SSID) is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive. Indicates the DIR-524. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or the wireless network. When select on, your wireless network name is broadcast to anyone within the range of your signal. If you're not using encryption then they could connect to your network. When select off, SSID will hide, you must enter the SSID on the client manually to connect to the network. Selecting On enables AP isolation mode. When enabled, STAs associated to the AP will not be able to communicate with each other. Wireless Network Name:
Channel:
SSID Broadcast:
AP Isolation :
D-Link DIR-524 User Manual 22 Section 3 Configuration Wireless Security Settings It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Select WEP in the Security Mode . 2. Select WEP Key Length. 3. Enter a Phrase and click Generate button to generate 4 keys. 4. And you can enter the Key manual. 5. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WEP on your adapter and enter the same passphrase as you did on the router. WEP is the wireless encryption standard. To use it you must enter the same key(s) into the router and the wireless stations. For 64 bit keys you must enter 10 hex digits into each key box. For 128 bit keys you must enter 26 hex digits into each key box. A hex digit is either a number from 0 to 9 or a letter from A to F. You may also enter any text string into a WEP key box, in which case it will be converted into a hexadecimal key using the ASCII values of the characters. A maximum of 5 text characters can be entered for 64 bit keys, and a maximum of 13 characters for 128 bit keys. D-Link DIR-524 User Manual 23 Section 3 Configuration 1.The Security Mode include WPA Personal Only, WPA2 Personal Only,Auto(WPA or WPA2 Personal). You can select one of them to configure. 2. Next to Cipher Type, select TKIP + AES, TKIP, or AES. If you have wireless clients that use both types, use TKIP + AES. 3. Next to Pre-Shared Key, enter a key (passphrase). The key is entered as a pass-phrase in ASCII format at both ends of the wireless connection. The passphrase must be between 8-63 characters. 4. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable the Security mode on your adapter and enter the same passphrase as you did on the router. D-Link DIR-524 User Manual 24 Section 3 Configuration WDS Setting Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS. WDS MAC :
Bridge Restriction:
Set another AP's MAC address. The MAC address must be the Wireless MAC address of the AP. Selecting Disabled disables wireless bridge restriction. Any wireless bridge (including the ones listed in Bridges) will be granted access. Selecting Enabled enables wireless bridge restriction. Only in Bridges will be granted access. those bridges listed Bridge Link Detection Interval:
Set the Wireless bridge link detection interval in seconds. Leave blank or set to zero to disable the detection. D-Link DIR-524 User Manual 25 Section 3 Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. IP Address:
Enter the IP address of the router. The default IP address is 192.168.0.1. Subnet Mask: Enter the Subnet Mask of the router. DHCP SERVER SETTINGS:
Enable DHCP Server:
DHCP Start IP Address :
Maximum DHCP Users:
Select Enabled to enable the DHCP server on your router. Select Disabled to disable this function. Enter the starting and ending IP addresses for the DHCP servers IP assignment. Limiting number of DHCP users. DHCP Lease Time : The length of time for the IP address lease. Enter the Lease time in minutes. Add DHCP Reservation :
Enable: Check the box to enable this function. IP Address:
Enter the IP address you want to assign to the computer or device. This IP Address must be within the DHCP IP Address Range. MAC Address: Enter the MAC address of the computer or device.And click the Copy Your PCs MAC Address button to to replace the Internet ports MAC address with the MAC address of your Ethernet card. The List show Reservation. DHCP Reservations List :
DHCP Clients List : The List show the clients that had the dynamic IP the clients of the DHCP Address . D-Link DIR-524 User Manual 26 Section 3 Configuration Advanced configuration Port Forwarding The Port Forwarding option is used to open a range of ports through your firewall and redirect data through those ports to a single PC on your network. Name: Enter a name for the rule . Public Port Start/
Public Port End:
Enter the port or a range of ports that you want to enable the port forwarding. Traffic Type: You can select TCP,UDP,BOTH. IP Address:
Enter the IP address of the computer on your local network that you want to enable the function. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the Select DHCP Client drop-down menu. Select your computer and click <<. Select Enabled to enable the rule and click Add to add the rule. The List show the rules you configured. Enable:
Port Forwarding Rules List :
D-Link DIR-524 User Manual 27 Section 3 Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-524. If you need to run applications that require multiple connections, specify the port normally associated with an application in the Incoming Ports , select the protocol type as TCP or UDP, then enter the Outgoing ports associated with the Incoming ports to open them for inbound traffic. Name: Enter a name for the rule . Enter the port or a range of ports that you want to use application rules . Select TCP, UDP, or BOTH from the drop-down menu. Enter the port or a range of ports that you want to access application rules on the WAN. The List show the rules you configured. Incoming Port Start/ Incoming Port End:
Traffic Type:
Outgoing Port Start/ outgoing Port End:
Application Rules List :
D-Link DIR-524 User Manual 28 Section 3 Configuration Access Control The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games. Default Rules: Select Allow all to pass except the following settings, if you only want to the selected computers to have network access and all other computers not to have network access. Select Deny all to pass except the following settings, if you want all computers to have network access except those computers in the list. Enter a name to your policy. Policy Name:
Time Filter : Week:Choose the day of the week you would like your policy to be applied. Time:Enter the time of the day you would like your policy to apply. You may choose some PCs based on MAC address to access Internet. You may choose some PCs based on IP address to access Internet. MAC Address Filter :
IP Address Filter :
Ports Filter : You may choose some PCs based on Port to access Internet. D-Link DIR-524 User Manual 29 Section 3 Configuration Website Filters Website Filters are used to allow you to set up a list of allowed Web sites that can be used by multiple users through the network. URL Filter : You may choose some PCs based on URL to access Internet. Enter URLs that you want to deny. You may choose some PCs based on Keyword Internet. Enter keywords that you want to deny. Keyword Filter :
to access Example :
If you wanted to block LAN users from any website containing a URL pertaining to shopping, you would need to enter shopping into the Website Filtering Rules list. Sites like these will be denied access to LAN users because they contain the keyword in the URL. http://www.XXX.shopping.com/stores.html D-Link DIR-524 User Manual 30 Section 3 Configuration Firewall Settings A firewall protects your network from the outside world. The D-Link DIR-524 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world. SPI Firewall:
Block WAN PING:
the that SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates the session conforms to the protocol. For added security, it is recommended that you enable the Block PING WAN option. Ping is often used by malicious Internet users to locate active networks or PCs. traffic passing through the Internet's Block IDENT: Block Identification used port 113. Port 113 is associated with Ident/Auth
(Identification / Authentication) service. When a client program in your computer contacts a remote server for services such as POP, IMAP, SMTP, or IRC, that remote server sends back a query to the
"Ident" server running in many systems listening for these queries on port 113. If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer. Enter the DMZ IP Address. Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort. Make sure VPN passthrough is enabled if you are trying to use a VPN client from behind the router. Enable DMZ Host:
VPN Passthrough :
D-Link DIR-524 User Manual 31 Section 3 Configuration Advanced Wireless Settings It is recommended that you leave wireless parameters at their default values. Adjusting them could limit the performance of your wireless network. Fragmentation Threshold:
RTS Threshold:
DTIM Interval:
Beacon Interval:
Preamble Type:
The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting. This value should remain at its default setting of 2432. If inconsistent data flow is a problem, only a minor modification should be made.
(Delivery Traffic Indication Message) 3 is the default setting. A DTIM is a countdown informing clients of to for broadcast and multicast messages. Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. The Preamble Type defines the length of the CRC (Cyclic Redundancy Check) block for communication between the Access Point and roaming wireless adapters. Make sure to select the appropriate preamble type and click the Save Settings button. the next window listening WMM Support:
WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients. D-Link DIR-524 User Manual 32 Section 3 Configuration Wireless MAC Filter The Wireless MAC (Media Access Controller) Address filter option is used to control wireless network access based on the MAC Address of the network adapter. A MAC address is a unique ID assigned by the manufacturer of the network adapter. This feature can be configured to ALLOW or DENY wireless access. If you choose ALLOW computers listed to access the wireless, only those clients whose wireless MAC addresses are in the access control list will be able to connect to your wireless router. When Deny computers listed to access the wireless is selected, these wireless clients on the list will not be able to connect the wireless router. D-Link DIR-524 User Manual 33 Section 3 Configuration Advanced Network If you are not familiar with these Advanced Network settings, please read the help section before attempting to modify these settings. UPnP UPnP is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment,software, and peripherals. This is an UPnP enabled router, meaning it will work with other UPnP devices/software. If you do not want to use the UpnP functionality, you can disable it. DNSMasq DNSMasq is a lightweight, easy to configure, DNS forwarder and DHCP server, designed to provide DNS
(and optionally DHCP) services to a small-scale network.When DNSMasq is enabled, the client will set the router IP address as a DNS address, if DNSMasqis disabled, you must set a DNS address by manual. D-Link DIR-524 User Manual 34 Section 3 Configuration Static Routing The static routing function determines the path that data follows over your network before and after it passes through your router. You can use static routing to allow different IP domain users to access the Internet through this device. Destination IP : Enter the routing destination IP address. Enter the routing subnet mask. Enter the routing gateway. Subnet Mask:
Gateway:
Metric:
the number of It means equipment that the data will pass. the network Interface: Select the interface to transmit the data out the router. D-Link DIR-524 User Manual 35 Section 3 Configuration tools Administrator Settings This page will allow you to change the Administrator and User passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser. User Accounts:
Password/
Confirm Password:
Enable Remote Management:
IP Address range:
Enter a name for the Administrator Login Name. The administrator can make changes to the settings. Enter the Administrator.Then enter the password again to confirm it. password new the for interface. the Web-Management the built-in web pages Remote management allows the DIR-524 to be configured from the Internet by a web browser. A username and password is still required to access In general, only a member of your network can browse to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote
(Internet) host. you can specify the IP address of the computer on the Internet that you want to have access to your router, or You can enable Any Remote IP to allow access to any computer on the Internet. Port: The port number used to access the DIR-524.Example: http://x.x.x.x:8080 whereas x.x.x.x is the Internet IP address of the DIR-524 and 8080 is the port used for the Web Management interface. D-Link DIR-524 User Manual 36 Section 3 Configuration Time Settings The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone:
Enable Daylight Saving:
Enable NTP Server:
NTP Server :
Select the Time Zone from the drop-down menu. To select Daylight Saving time manually, Chack the box, and enter a start date and an end date for daylight saving time. NTP stands for Network Time Protocol. NTP synchronizes computer clock in a network of computers. Check this box to use a NTP server. This will only connect to a server on the Internet, not a local server. Enter the NTP server or select one from the drop-down menu, then the DIR-524 will sync the same time to D-Link Internet time server. times Manual: To manually input the time, enter the values in these fields for the Year, Month, Day, Hour, Minute, and Second . the Copy Your And you can Press Computers Time Settings button to set the devices time the same to local PC. D-Link DIR-524 User Manual 37 Section 3 Configuration System The System Tools section allows you to reboot the device, or restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you have created. Save to Local Hard Drive:
Load from Local Hard Drive:
Restore to Factory Default s:
Reboot the Device:
Use this option to save the current router configuration settings to a file on the hard disk of the computer you are using. First, click the Save configuration button. You will then see a file dialog, where you can select a location and file name for the settings. Use this option to load previously saved router configuration settings. First, use the Browse to find a previously save file of configuration settings. Then, click the Restore Configuretion from File button to transfer those settings to the router. This option will restore all configuration settings back to the settings that were in effect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router configuration settings, use the Save configuration button above. Click to reboot the router. D-Link DIR-524 User Manual 38 Section 3 Configuration Firmware There may be new firmware for your router to improve functionality and performance. To upgrade the firmware, locate the upgrade file on the local hard drive with the Browse button. Once you have found the file to be used, click the Upgrade button below to start the firmware upgrade. D-Link DIR-524 User Manual 39 Section 3 Configuration DDNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is. the Username Choose your DDNS provider from the drop down menu. Enter the Host Name that you registered with your DDNS service provider. Enter account. Enter account. This is to test if the DDNS account is valid for use. for your DDNS for your DDNS the Password Server:
Host Name:
Username :
Password :
Timeout:
D-Link DIR-524 User Manual 40 Section 3 Configuration PING TEST The System Check feature allows you to verify the physical connectivity on both LAN and Internet interface. Ping Test: The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping. Ping Results: The results of your ping attempts will be displayed here. D-Link DIR-524 User Manual 41 Section 3 Configuration LOG SETTINGS The router automatically logs (records) events of possible interest in its internal memory. If there isnt enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log files to a computer on your network that is running a Syslog utility. Select Enabled then the router will record the events in its internal memory. Check the box then the router will send these logs to another location. And enter the IP Address of the computer you want to send the log files. Click the Save button to save the logs to local hard drive or to syslog server. Enable Log:
Enable Remote Log:
Save Logs:
D-Link DIR-524 User Manual 42 Section 3 Configuration Status Device Information All of your Internet and network connection details are displayed on this page. The firmware version is also displayed here. D-Link DIR-524 User Manual 43 Section 3 Configuration LOGS Display the captured log messages of the router activities, these captured log meesages might be useful for troubleshooting and monitoring. D-Link DIR-524 User Manual 44 Section 3 Configuration Traffic Statistics Traffic Statistics display Receive and Transmit packets passing through the router. D-Link DIR-524 User Manual 45 Section 3 Configuration Wireless The Wireless Client table below displays Wireless clients Connected to the Router. D-Link DIR-524 User Manual 46 Section 3 Configuration Support D-Link DIR-524 User Manual 47 Section 4 Security Internet Ping Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-524 offers the following types of security:
WPA2 (Wi-Fi Protected Access 2) WPA (Wi-Fi Protected Access) What is WPA?
WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP:
Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys havent been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP. User authentication, which is generally missing in WEP, through the extensible authentication protocol
(EAP). WEP regulates access to a wireless network based on a computers hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network. WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point. WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network. D-Link DIR-524 User Manual 48 Section 4 Security Configure WPA-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router
(192.168.0.1). Click on Setup and then click Wireless Settings on the left side and then click Manual Wireless Network Setup. 2. Next to Security Mode, select WPA-Personal. 3. Next to Cipher Type, select TKIP and AES, TKIP, or AES. If you have wireless clients that use both types, use TKIP 4. Next to Pre-Shared Key, enter a key (passphrase). The key is entered as a pass-phrase in ASCII format at both ends of the wireless connection. The pass-phrase must be between 8-63 characters. 5. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router.
+ AES. D-Link DIR-524 User Manual 49 Section 5 Connecting to a Wireless Network Connect to a Wireless Network Using Windows Vista or Windows Vista users may use the built-in wireless utility. If you are using another companys utility or Windows 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a site survey option similar to the Windows Vista utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select Connect to a network. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DIR-524 User Manual 50 Section 5 Connecting to a Wireless Network Configure WPA/WPA2 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. D-Link DIR-524 User Manual 51 Section 5 Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router. D-Link DIR-524 User Manual 52 Section 5 Connecting to a Wireless Network Using Windows XP or Windows XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another companys utility or Windows 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a site survey option similar to the Windows XP utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DIR-524 User Manual 53 Section 6 Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-524. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows XP. If you have a different operating system, the screen shots on your computer will look similar to the following examples.) 1. Why cant I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. Make sure you have an updated Java-enabled web browser. We recommend the following:
Internet Explorer 6.0 or higher Netscape 8 or higher Mozilla 1.7.12 (5.0) or higher Opera 8.5 or higher Safari 1.2 or higher (with Java 1.3.1 or higher) Camino 0.8.4 or higher Firefox 1.5 or higher Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on. Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. D-Link DIR-524 User Manual 54 Section 6 Troubleshooting Configure your Internet settings:
Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times. Close your web browser (if open) and open it. Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your the web management. If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer. 2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults. To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty. D-Link DIR-524 User Manual 55 Section 6 Troubleshooting 3. Why cant I connect to certain sites or send and receive e-mails when connecting through my router?
If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, youll have to do a special ping of the destination youre trying to go to. A destination could be another computer, or a URL. Click on Start and then click Run. Windows 95, 98, and Me users type in command (Windows NT, 2000, and XP users type in cmd) and press Enter (or click OK). Once the window opens, youll need to do a special ping. Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472 D-Link DIR-524 User Manual 56 Section 6 Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network were working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size. To change the MTU rate on your router follow the steps below:
Open your browser, enter the IP address of your router (192.168.0.1) and click OK. Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page for the device. Click on Setup and then click Manual Configure. To change the MTU enter the number in the MTU field and click Save Settings to save your settings. Test your e-mail. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten. D-Link DIR-524 User Manual 57 Appendix A Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers. A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link. D-Link DIR-524 User Manual 58 Appendix A Wireless Basics What is Wireless?
Why D-Link Wireless?
How does wireless work?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network. Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN). Wireless Local Area Network (WLAN) In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues. D-Link DIR-524 User Manual 59 Appendix A Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesnt use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries. Wireless technology as become so popular in recent years that almost everyone is using it, whether its for home, office, business, D-Link has a wireless solution for it. Who uses wireless?
Home Gives everyone at home broadband access Surf the web, check e-mail, instant message, and etc Gets rid of the cables around the house Simple and easy to use Small Office and Home Office Stay on top of everything at home as you would at office Remotely access your office network from home Share Internet connection and printer with multiple computers No need to dedicate office space D-Link DIR-524 User Manual 60 Appendix A Wireless Basics Where is wireless used?
Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and its becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called hotspots. Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers. Wireless network is easy to setup, but if youre installing it for the first time it could be quite a task not knowing where to start. Thats why weve put together a few setup steps and tips to help you through the process of setting up a wireless network. Here are a few things to keep in mind, when you install a wireless network. Centralize your router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range. Tips Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency. D-Link DIR-524 User Manual 61 Appendix A Wireless Basics Security Dont let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking:
Infrastructure All wireless clients will connect to an access point or wireless router. Ad-Hoc Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DIR-524 wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate. D-Link DIR-524 User Manual 62 Appendix B Networking Basics Networking Basics Check your IP address After you install your adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server
(i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows Vista users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters. D-Link DIR-524 User Manual 63 Appendix B Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step 1 Windows Vista - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Click on Start > Control Panel > Network Connections. Windows XP -
Windows 2000 - From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your network adapter and select Properties. Step 3 Highlight Internet Protocol (TCP/IP) and click Properties. Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the routers LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings. D-Link DIR-524 User Manual 64 Appendix C Technical specifications Technical Specifications Standards IEEE 802.11b IEEE 802.3 IEEE 802.11g IEEE 802.3u IEEE 802.11n IEEE 802.3x Wireless Signal Rates 135Mbps 121.5Mbps 108Mbps 81Mbps 54Mbps 40.5Mbps 27Mbps 13.5Mbps 9Mbps 6Mbps 5.5Mbps 2Mbps 1Mbps Security Transmitter Output Power 11b:17dBm(Max) 11g:15dBm(Max) 11n:14dBm(Max) Operating Temperature 32F to 129 F0C to 40C Operating Humidity 10%-90% non-condensing Safety & Emissions FCC Part 15B/ 15C/ MPE IC RSS-210 NCC LP0002 LED Power WLAN LAN INTERNET Dimensions WPA WPA2 64/128-bit WEP L =141 mm W = 110.4mm H = 31.7mm Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume
of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range. D-Link DIR-524 User Manual 65 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Appendix D Contacting Technical Support Copyright 2008 by D-Link Corporation/D-Link Systems, Inc. All rights reserved. CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office. FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. D-Link DIR-524 User Manual 66
This product uses the FCC Data API but is not endorsed or certified by the FCC