EG07170 IBU_SMK User manual

3.Outline of the system Existing BCM, SMK, TPMS receiver integrated ECU as well as smart key function. Body and TPMS related control unit (integrated PDM, RF Receiver). It controls the power operation mode (ACC, IGN1, IGN2, START) of the vehicle according to the operation of the START / STOP button when the card key / FOB is successfully authenticated. Various Lamp, Indicator, Rear Curtain, Side mirror, Relay control related to BCM function Directly and indirectly, and performs a warning and display function for processing data received from the TPS sensor. 3.1. IBU WSMK Smart Key System The smart key unit controls the smart key system. When the user inputs the door handle or the start button, the smart key unit transmits the LF signal (134.2 KHz) to the smart key FOB and receives the signal (433 MHz) from the FOB to perform a related function . Terminal control function: Control terminal (IGN1, IGN2, ACC) power when inputting start / stop button Immobilizer function: Function for emergency start or RKE key authentication when discharging FOB battery Start stop button LED lighting control Electrical steering colume lock (ESCL) control function - excluding domestic / North American / Canadian specifications BCM function System BCM function is a function for user convenience / warning, and it can directly or indirectly control various through communication or switch input. It also performs Immobilizer function. indicators, sensor power, hot wire and relay control Terminal control function: IGN1, IGN2, ACC power control Immobilizer function: Perform function for RKE Key authentication Head lamp washer relay control function - Optional function Indicator control function Auto light control function Puddle & Pocket Lamp control function Solenoid control function (ATM) PAS power control function LIN communication Chassis CAN communication (500kbps) Body CAN communicaton (500kbps) 3.2. LF Antennas:

Inductive antennas in and at the vehicle are used to transform the current, driven by the SMK antenna driver, into a magnetic field (134.2 kHz), which is the carrier for the SMK challenge. Two antenna covers the vehicles interior. One antenna covers the interior of the Trunk. Two antennas in the Door Handles (Left side and Right side) cover the area around the doors. One antenna in the rear bumper covers the area around the trunk for access to the trunk. Those antennas are based on ferrite core and have a pair of twisted copper cables from antenna to pin header. 3.3. Transponder Antenna:

Built in the Start Stop Button to communicate with the transponder by a base station and using wireless communication :(134.2kHz) 3.4 Installation in vehicle The Smart Key ECU is installed inside the vehicle. Smart Key FOB RF ANT LF ANT TP ANT RF Receiver LF ANT Driver IBU(SMK ) Transponder Driver Installation in vehicle Fig. Outline of the System Smart Key FOB Door Handle with LF Antenna Start Stop Button with Transponder Antenna LF Antenna SMK+BCM With RF Internal Antenna RF Receiver and LF Driver Fig. Installation of the System FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Warning

"This device complies with Industry Canada licence-exempt RSS standard(s)."

Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas provoquer de brouillage, et (2) l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.