submitted | available | document details (if available) | source link |
---|---|---|---|
various | User Guide Rev B | Users Manual | 1.28 MiB |
K001-00777-00 EVO - HD Users Guide Copyright 2019, Digital Ally, Inc. All Rights Reserved, Printed in U.S.A. This publication may not be reproduced, stored in a retrieval system, or transmitted in whole or part in any form or by any means electronic, mechanical, recording, photocopying, or in any other manner without the prior written approval of Digital Ally, Inc. EVO-HD Users Guide K001-00777-00 Table of Contents IMPORTANT SAFETY INFORMATION..................... ERROR! BOOKMARK NOT DEFINED. POWERING THE EVO-HD ............................................ ERROR! BOOKMARK NOT DEFINED. BASIC OPERATION ........................................................ ERROR! BOOKMARK NOT DEFINED. INDICATORS AND CONTROLS ..............................................ERROR! BOOKMARK NOT DEFINED. DVF RECORDER .................................................................ERROR! BOOKMARK NOT DEFINED. LED LAMPS ........................................................................ERROR! BOOKMARK NOT DEFINED. HAND HELD MODE ........................................................ ERROR! BOOKMARK NOT DEFINED. HOW TO START/STOP A RECORDING ...................................ERROR! BOOKMARK NOT DEFINED. EXTERNAL MONITOR MODE ..................................... ERROR! BOOKMARK NOT DEFINED. LOGIN PROCEDURE .............................................................ERROR! BOOKMARK NOT DEFINED. MAIN MENU .......................................................................ERROR! BOOKMARK NOT DEFINED. Playback .......................................................................... Error! Bookmark not defined. Record ............................................................................. Error! Bookmark not defined. Pre-Event Record ............................................................ Error! Bookmark not defined. Assign Event ID ............................................................... Error! Bookmark not defined. Erase File ........................................................................ Error! Bookmark not defined. Settings ............................................................................ Error! Bookmark not defined. Logout ............................................................................. Error! Bookmark not defined. SETTINGS MENU .................................................................ERROR! BOOKMARK NOT DEFINED. Date/Time Menu .............................................................. Error! Bookmark not defined. Display Text Menu .......................................................... Error! Bookmark not defined. Record Settings Menu ...................................................... Error! Bookmark not defined. Battery
............................................. Error! Bookmark not defined. LED Management Menu Indicators Menu ...................................................... Error! Bookmark not defined. Reset To
............................................... Error! Bookmark not defined. Reset Factory Defaults Application Verification ......................................... Error! Bookmark not defined. Erase All Videos .............................................................. Error! Bookmark not defined. DOWNLOAD MODE........................................................ ERROR! BOOKMARK NOT DEFINED. HOW TO MANUALLY DOWNLOAD VIDEOS ...........................ERROR! BOOKMARK NOT DEFINED. HOW TO UPLOAD VIDEOS INTO VIDEOMANAGER ................ERROR! BOOKMARK NOT DEFINED. TROUBLESHOOTING .................................................... ERROR! BOOKMARK NOT DEFINED. HOW TO RESET THE EVO-HD ............................................ERROR! BOOKMARK NOT DEFINED. HOW TO UPGRADE/REFRESH THE EVO-HD SYSTEM SOFTWARE ....... ERROR! BOOKMARK NOT DEFINED. PRODUCT REPAIR................................................................ERROR! BOOKMARK NOT DEFINED. LIMITED WARRANTY ................................................... ERROR! BOOKMARK NOT DEFINED. CONTACT US ................................................................... ERROR! BOOKMARK NOT DEFINED. APPENDIX A EVO-HD KIT ......................................... ERROR! BOOKMARK NOT DEFINED. APPENDIX B EVO-HD SPECIFICATIONS .............. ERROR! BOOKMARK NOT DEFINED. REGULATORY APPROVALS .................................................ERROR! BOOKMARK NOT DEFINED. APPENDIX C UPGRADING/REFRESHING THE EVO-HD SOFTWARE ............... ERROR!
BOOKMARK NOT DEFINED. Page 2 of 10 EVO-HD Users Guide K001-00777-00 Section 1: FCC Notice Federal Communications Commission This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. equipment generates, radiate uses, This and can Changes or modifications not expressly approved by Digital Ally, Inc. could void the users authority to operate the equipment. For compliance with RF exposure requirements, please maintain 20cm of separation between the device and all users during operation. Section 2: Introduction to the EVO-HD HD System 2.1. Overview of Features External road facing 1080p High Definition IP camera with 10x variable optical zoom A back seat 1080p camera built IR illumination. Capable of recording two video channels simultaneously Integrated 3:4 monitor to trigger and review videos Wireless Microphone with 3000 foot range Recordings can be started by any of the following:
Automatically by the G-Force sensor (cornering, braking, and collision), GPS coordinates, Vehicle Speed, IF Box sensors (sirens, lights, covert switch, etc.) Manually by using the Record Button Wireless Microphone Body camera FVHD Mobile Data Terminal (MDT) EVO Application Recordings end:
When active input sensor trigger ends Manually by using the Record Button Page 3 of 10 EVO-HD Users Guide K001-00777-00 Pre-Event recording will capture up to 30 seconds prior to the start of a recording. Pre-Event Record time is adjustable in 6 second increments Records metadata with the audio and video, including device serial number, vehicle speed, date, time, sensors, radar, and GPS coordinates Automated wireless 802.11b/g/n upload of video events to your back office server Configuration and device updates can be wirelessly downloaded to each vehicle Easy to use with minimal or no driver interaction required Secure user login to the EVO-HD User may add traffic stop profile information at time of event Integrated playback controls for in-vehicle viewing LED and monitor status indicators Configurable monitor brightness for day and night modes VuVault back office software available for organizing and viewing video event files, and advanced device configuration Page 4 of 10 EVO-HD Users Guide K001-00777-00 2.2. EVO-HD Features Diagram 1 2 3 4 5 6 7 8 9 10 13 12 11 Page 5 of 10 EVO-HD Users Guide K001-00777-00 Ethernet Port/ RJ45: POE switch or MDT is connected here 1 Wireless Microphone input 2 GPS Port: The GPS antenna is connected here. 3 Cell Port: The 4G LTE antenna is connected here. 4 Wi-Fi Port: The Wi-Fi antenna is connected here. 5 6 USB ports: USB cameras connected here 7 8 9 MON port: the monitor connected here 10 11 External SD Card: A removable SD card is installed at the bottom of the device 12 LED Status Indicators (Green Power good, Red Cell disconnected, and yellow uploading) PWR port: 12 to 30V input to power EVO-HD I/O port: the trigger inputs and outputs connected here Reset Button: Used to perform a hard reset of the system. 13 EVO-HD FCC Label & Serial Number Section 3: EVO-HD Configuration Overview 3.1. Wireless Configuration Update The EVO-HD will check for the latest firmware updated after or before uploading the videos. This process is automated the user will not need to initiate the process. Once the update process has started:
Do not remove power Do not remove the external SD card 3.2. Using VuVault to Configure your EVO-HD VuVault is used to manage EVO-HD settings as well as activate your device or an external. Before you can configure your device for use within VuVault, the EVO-HD serial number must be added into the system. Add your device into VuVault by selecting Admin > Devices > Advanced > Add Device. Find the device serial number located on the back of the EVO-HD and type it into the wizard (do not include the hyphen). Assign it a name and description. When done, press Save. For more information consult the VuVault Administrator Guide Adding Devices section. Go to the Admin > Devices Tab. A separate configuration field for EVO-HD Settings will be available once a valid serial number for the device has been added into the system. These settings will define how all users will interface with the EV)-HD. Click on each subheading to reveal the available configuration options. When finished, press Save. The Default button in the lower part of the main screen configurations for this device to the factory settings Page 6 of 10 EVO-HD Users Guide K001-00777-00 Section 4: EVO-HD Power The Power operation is configurable and specifies how the EVO-HD will operate when the vehicle ignition is turned to the ON or OFF positions. Two parameters control the power operation in order as follows:
4.1. Ignition Shutdown Timer The Ignition Shutdown Timer specifies the amount of time the remains EVO-HD fully powered when the vehicle ignition goes from ON to OFF. During the Ignition Shutdown Time:
1. The EVO is fully powered and operational, including all high power consumption devices, such as; cameras
(including Pre-Event), recorded audio, GPS, Monitor, and the pre-event buffer. 2. The EVO-HD will remain fully powered until the Ignition Shutdown Timer expires. When the timer expires, the EVO-HD will then follow the operation for the Days in LPS configuration. 3. If the vehicle ignition switches on before the timer expires, the Ignition Shutdown Timer is canceled and will start over again when the ignition is turned off. 4.2. Days in LPS (Low Power Standby) When the vehicle ignition goes from ON to OFF the EVO-HD will first follow the operation for Ignition Shutdown Timer and then the operation for Days in LPS configuration. The Days in LPS configuration specifies the number of consecutive days the EVO-HD will remain in Low Power Standby before completely powering off. Using a Low Power Standby configuration ensures the EVO-HD is fully powered on and ready to record within a few seconds of the vehicle ignition switching on. Settings: 0 to 10 days [default = 0 days]
During Low Power Standby:
4. All high power consumption devices will be turned off, such as; cameras (including Pre-Event), GPS, monitor, ECA recording, and the pre-event buffer. If configured, Accelerometer, External Triggers, and the Manual Record button events will trigger an event record. All other triggers are unavailable during low power standby. 5. The EVO-HD will remain in Low Power Standby until the number of days expires. When the number of days expires, the EVO-HD will completely power off. 6. If the vehicle ignition switches to the ON position before the number of days in Low Power Standby expires, the EVO-HD will wake up to the full power state and be ready to record within a few seconds. The EVO-HD will draw a maximum of 20mA of current during Low Power Standby. Typically, a new or strong vehicle battery will provide enough current to power the EVO-HD in LPS for at least 10 days without discharging the battery. The vehicles battery current rating, battery age, and other equipment that remains powered on when the vehicle ignition is off will affect the maximum consecutive days the EVO-HD should remain in LPS. Section 5: Input Sensor Device Detection, Threshold, and Wiring Guide To configure an input sensor, the signaling of the device must be known. To determine the signaling, measure the voltage for the normal or inactive state of the device and the voltage for the triggered or active state. Use the input sensor worksheet located in your installation guide to record measurements. When configuring sensors, first determine the Trigger Operation; second, the direction for the Detection Type; then select the Threshold setting nearest to the triggered state. The figure below illustrates these steps:
Detection and Threshold Parameters for Input Sensors Page 7 of 10 EVO-HD Users Guide K001-00777-00 Signal from Trigger Device Configuration Setting Detection Type Threshold Normal or Inactive State 5V Triggered or Active State GND High to Low 12V GND High to Low 28V GND High to Low GND OPEN Low to High GND 5V GND 12V GND 28V OPEN GND Low to High Low to High Low to High High to Low EVO-HD input/output cable interface and wiring color code Standard Standard Standard Standard Standard Standard Standard Standard Wire Color/Code 1. RED WHITE STRIPE 2. BROWN 3. RED 4. YELLOW 5. BLUE WHITE STRIPE 6. WHITE 7. GREEN 8. ORANGE 9. BLUE 10. BLACK 11. PINK 12. GRAY Wiring Diagram Assignment 24W Out/ Trigger Out OUTPUT (going to Mic Trig in) REVERSE (Input) VEHSS OUTPUT 2 SIREN INPUT (going to Mic Trig OUT) LIGHTBAR (INPUT) BRAKE (INPUT) GND (POE INJ/Wireless Mic) RADAR IN RADAR GND Page 8 of 10 EVO-HD Users Guide K001-00777-00 Page 9 of 10 Section 6: Contact Information 9705 Loiret Blvd Lenexa, KS 66219 Website: www.digitalallyinc.com Support E-Mail: support@digitalallyinc.com Sales E-Mail: sales@digitalallyinc.com Phone: 913-814-7774 Fax: 913-814-7775 Sales / Support Toll Free: 1-800-440-4947
* Specifications subject to change without notice. Page 10 of 10
This product uses the FCC Data API but is not endorsed or certified by the FCC