600D WLAN module User Manual

Rugged Tablet BASIC OPERATION GUIDE DT311Y INTRODUCTION Thank you for acquiring the DT311Y, part of DT Researchs line of tablets. Featuring a slim yet robust enclosure, the DT311Y with 11.6 capacitive touch display is powered by the Intel processor, offering optimal combinations of performance and power savings. The DT311Y is available with Microsoft Windows operating system. The operating system features web browser, client/ server computing software, media player, accessories, and applications support. PACKAGE CONTENTS One DT311Y with Battery Pack and Handstrap AC-DC Power Adapter with Power Cord Basic Operation Guide Guide for detailed operation.

* If your DT311Y contains camera or barcode scanner, please refer to the Tablet Modules Basic Operation 1 DT311Y:

Input/ Output Ports Button Functions A Headphone Jack BUTTON ACTION 1 2 3 power button programmable buttons Battery Latch Push the switch to unlock the latch, than slide the latch to left to remove the battery. B LAN Port C USB 3.0 Port D USB Type-C Port E Smart Card Reader 2 PRECAUTIONS Always exercise care when operating and handling the DT311Y. Do NOT apply excessive pressure to the display screen. We recommend using the Digital Pen (optional) to keep the screen clean. Avoid prolonged exposure of the display panel to any strong heat source. Wherever possible, the DT311Y should face away from direct light to reduce glare. If the AC-DC power adapter is used to recharge or power the tablet, do NOT use any AC-DC adapter other than the one provided or acquired from the manufacturer or its partners. In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power off the DT311Y and disconnect all power sources. Report the problem to your device provider immediately. Never attempt to disassemble the DT311Y, as this will void the warranty. NOTE:

To obtain protection consistent with any IP rating for the device, the I/O (audio, power, USB, card reader, etc.) port doors must be closed. If the IP protection is compromised by mishandling or misuse, such as by leaving port doors open or improperly closed, any resulting product damage will not be covered under any DT Research warranty. BASIC FEATURES The DT311Y wireless tablet integrates a bright display, one USB port, and embedded networking elements such as wireless LAN and Bluetooth or optional 4G LTE. The DT311Y is complemented by a suite of accessories, including battery expansion, charging cradles, and battery charger kit, for a comprehensive user experience. A DT311Y typically integrates an 802.11ac wireless LAN (WLAN) adapter that may connect to other wireless devices or access points. If your DT311Y does not come with such a network adapter, please consult your device provider to establish the desired network connectivity. 3 Powering ON and OFF To activate the DT311Y, push and quickly release the Power Button. The display will come on in a few seconds. To put the DT311Y in Standby mode, push and quickly release the Power Button. To turn the DT311Y off for extended storage, power off safely using any software function that shuts down computer provided in the software operating system. The battery pack shipped with your tablet may be low in powerplease use the AC-DC adapter with the DT311Y when setting up for the first time to fully charge the battery pack, or use the optional When the battery pack is charging, the blue-colored Battery LED should blink slowly. If plugging in the AC-DC adapter does not trigger this blinking activity and the LED stays dark, the battery pack(s) may have been drained substantially. Try unplugging/ replugging the AC-DC adapter to the DT311Y a few times to activate the charging process. To conserve power, use (push and quick release) the Power Button to put the tablet in Standby mode while not in use. Pushing briefly on the same button will wake up the system within seconds. Avoid using the Power Button (hold 4+ seconds feature) to turn off the tabletthis form of hardware shutdown is intended to be a means of recovery from lockups, and not as normal OPERATION NOTE:

battery charger kit. NOTE:

NOTE:

NOTE:

operation. 4 Start Up established. If the power up (from Standby mode or otherwise) is successful, the appropriate interface will be displayed after a launch sequence of several seconds. The wireless LAN connection may take 10-15 seconds to be Configuring the Mobile Tablet The DT311Y may be configured using the utilities and methods dictated by the software operating system. The DT311Y should be configurable for various properties such as user profiles, network features, and several system elements. Wireless Networking Wireless LAN a hidden custom antenna. The DT311Y is often delivered with an embedded (user-inaccessible) 802.11ac WLAN adapter equipped with Through the support of typical WLAN adapters, the DT311Y should be able to detect all 802.11 access points in the vicinity for you to select the access point of your choice for connection. The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT311Y and the access points have to match. The SSID is case-sensitive and it is recommended that you enable WEP/WPA/WPA2 encryption (or advanced alternatives) for secure access. When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your networking equipment literature to properly configure associated settings such as Authentication mode, Refer to the access point operating manuals for setting up the 802.11 access points. etc. Bluetooth The Bluetooth configuration application is enabled from the System Tray or from the Windows Mobility Center. Follow the instructions and options provided within the application to configure and invoke Bluetooth connectivity with the corresponding peripherals. 5 USING THE MOBILE TABLET Peripherals Support Through its USB 3.0 port, the DT301Y supports a wide range of USB-based peripherals. These peripherals are applicable for software installation, applications storage, data storage, and system software recovery and updates. For More Support Users can download the Tablet Modules Basic Operation Guides from the DT Research website. If the DT311Y comes with a Mobile broadband module, please contact your product and/or service provider for the SIM Card installation procedures. To Hold the Tablet Left hand: grip the left back side of the tablet with your left hand four index fingers, with thumb resting on the top of the back side of the tablet and palm securely against the back. Right hand: grip the right back side of the tablet with your right hand four index fingers, with thumb resting on the top of the back side of the tablet and palm securely against the back. 6 Operating System Microsoft Windows 10 IoT Enterprise 11.6 LED-backlight, high-brightness (1000 nits) screen with capacitive touch, outdoor viewable Intel Core i5-8250U, Quad-Core, 1.6GHz (up to 3.4GHz) Intel Core i7-8550U, Quad-Core, 1.8GHz (up to 4.0GHz) DT311Y 8GB to 32GB 256GB to 2TB flash 1920 x 1200 Wi-Fi 802.11ac, 2.4GHz/ 5GHz dual band; Bluetooth 4.2 LE 1 power button, 2 brightness control buttons, 5 programmable buttons 1 power/ battery status LED Built-in speaker USB 3.0 x 1, USB Type C x 1 (for data transmitting and charging) 1 (3.5mm) Smart Card/CAC Reader Full-slot, reads ISO 7816 T=0, T=1; 1.8/3/5V smart card Mechanical and Environmental AC/DC Adapter Ethernet 10/ 100/ 1000MB Base-T LAN Input: 100 240V AC; Output: 20V DC, 3.25A Hot swappable battery, 11.4V, 5400mAh Hot swappable battery, 11.4V, 8000mAh (optional) ABS + PC plastics and magnesium-aluminum alloy 3.5 lbs/ 1.6 kg FCC Class B, CE, RoHS compliant Storage: -55C to 70C (-67F to 158F) 0% 90% non-condensing Operation: -10C to 60C (-14F to 140F), optional -30C to 45C (-22F to 113F) Dimensions (H x W x D) 8.3 x 12.4 x 0.86 in/ 212 x 316 x 21.9 mm Specifications:

Item System CPU RAM Storage Display Display Resolution Network Interface Control Switch and Buttons Indicator Speaker I/O Ports USB port Headset Jack Ethernet Battery Pack Enclosure Weight Regulatory Operating Temperature Humidity 7 DT311Y UHF RFID Reader Module Application One application for the DT311Y Rugged Tablet is to scan goods with RFID tags that are located far away in the warehouse. For this operation example, please see the picture below. Turn on the UHF RFID reader function, and face the reader module (on the back of the tablet) to the cartons, goods, etc. to capture the tag data. The reading distance is up to 30 feet. NOTE: Turn off the UHF RFID reader function while the module/ tablet is not in use. 8 Federal Communicaon Commission Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separaon between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Cauon: Any changes or modicaons not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. This device and its antenna(s) must not be co-located or operang in conjuncon with any other antenna or transmier. This Class [B] digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe [B] est conforme la norme NMB-003 du Canada. Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a new model device is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations as required by the FCC. DT Research, Inc. 2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com Copyright 2019, DT Research, Inc. All Rights Reserved. 9