GWS-GWCT Light Guided Operations Users Manual

HARDWARE USER MANUAL GWS-GWCT Light Guided Operations Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio technician for help Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the systems manufacturer could void the users authority to operate the equipment. FCC Label Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that may cause undersired opreation Canada, Industry Canada (IC) Notices This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis dIndustry Canada (IC) Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 1 Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has been evaluated for and shown compliant with the IC Specific Absorption Rate (SAR)limits when operated in portable exposure conditions. Informations concernant lexposition aux frquences radio (RF) La puissance de sortie mise par lappareil de sans fil est infrieure la limite dexposition aux frquences radio dIndustry Canada (IC). Utilisez lappareil de sans fil de faon minimiser les contacts humains lors du fonctionnement normal. Ce dispositif a t valu pour et dmontr conforme la Taux IC dabsorption spcifique (SAR) des limites lorsquil est utilis dans des conditions dexposition portatifs. o compliance to ALL applicable EU standards to support CE mark. o compliance to FCC 47 CFR Part 15 Subpart B & ICES-003 Issue 6-2016 o compliance to EU Radio Equipment Directive o compliance to FCC 47 CFR Part 15 Subpart C Safety Instruction Your system is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source such as a radiator. Set up the system on a stable surface. If you use an extension cord, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating. FCC CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the users authority to operate the equipment. 2 Attention during use If you encounter the following technical problems with the product, remove the battery and dispose the product to safe disposal. The system was dropped or the cabinet is damaged. The system performance changes. The system not function properly even if you follow the operating instructions. Liquid has been spilled into the system. The battery has damaged or dropped. The warranty does not apply to products that have been disassembled by users. Safety Notice and warnings Product disposal notice IMPORTANT:

In the European Union, this symbol indicates that this product including battery must not be disposed of with household waste. It is your responsibility to hand it over to a designated collection point for the recycling of waste electrical and electronic equipment. For more information, please contact your local waste collection center or the point of purchase of this product. CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Nordic Lithium Safety Notice (for lithium-ion batteries) Safety Notice:

Danger of explosoin if battery is incorrectly replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions. Attetion during use 1. Do not place this product underneath heavy loads or in an unstable position. 2. Do not use or expose this product around magnetic fields as magnetic interference may affect the performance of the product. 3. Do not storage this product to high levels of direct sunlight, high-humidity or wet conditions. 4. Do not carry the product on the body (or pockets). CAUTION:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 3 Brief Introduction Specifications Item Spec Description MCU LED Connectivity NFC Zigbee Sensors Battery Type Operating Temp Dimension (W x L x H) IP Level Battery Life Electrical Rating Telink 8269F512 ET32 3 Color LED (RGB) *2 2 Color LED *1

< 4 cm 30 m G-Sensor 18650 Li-lon Battery 2600mAH Rechargable

-10~50 96* 78 *52 mm IP 54 6 months 3.3V 4 How to Power On Tag:

How to Attach Tag:

Via Screws:

How to Open Top Cover By pulling the battery isolator strip away from the device, the Tag will power-on, which will be confirmed with an LED light blink. Tag device can attached by inserting fasteners, zip ties, nails or screws through the mounting holes located on each corner of the Tag and secured to the desired surface. Compress the top cover at the center points of the top and bottom as shown. To close the device, insert the cover closure tabs into the appropriate slots near the battery. Then compress the top cover in order to insert the other set of cover closure tabs near the LED lights. 5 How to Insert Battery When insert battery, the indication of high light area must face upward to prevent any short circuit from accident insert damage battery. Warning:

Check battery before insert to system for usage. Do not place damage battery for usage. If there is any damage on battery please dispose properly, and handle with battery instruction. 6 LED Light Behavior:

Color Green Condition Initial battery insert and battery voltage > 4.09V (88%

battery capacity) Red Red Initial battery insert and battery voltage < 4.09V (88%

battery capacity) Operational battery voltage <

battery threshold Voltage (set from cloud/AMZ application) Red Client state machine failure Green OTA Green OTA Period/duty cycle/blink rate 100ms ON 200ms OFF. Therefore a period of 300ms and duty cycle = 33%. 10 blinks and stops 100ms ON 200ms OFF. Therefore a period of 300ms and duty cycle = 33%

10 blinks and stops 500ms ON, 1500ms OFF. Therefore a period of 2s and duty cycle = 25%

One blink repeats every 2 secs. 100ms ON 400ms OFF. Therefore a period of 500ms and duty cycle = 20%

13 blinks with the 500ms period. This pattern repeats Blinking green: Blinks every 500 ms during the OTA update until the process completion. Solid green: during client flash erase. Will last until the flash erase and should then resume blinking green 7 GWS-GWCT Light Guided Operations Elitegroup Computer Systems Co., LTD. No. 239, Sec. 2, Tiding Blvd., Neihu District, Taipei City, Taiwan (11493)