| submitted | available | document details (if available) | source link |
|---|---|---|---|
| J2_680_System_Manual_1.0.pdf avinchan GPL Ghostscript 8.15 |
| various | Users Manual | Users Manual | 2.98 MiB |
J2 680L Integrated Touchscreen Computer System Manual May 2012 Copyright 2011-2012 J2 Retail Systems Ltd All rights reserved Change history Version 1.0 Release May 11, 2012 J2 680 System Manual Version 1.0 May 11, 2012 2 Overview ............................................................................................................................ 6 Specification ....................................................................................................................... 8 Features ............................................................................................................................ 10
............................................................... 10 Hot Swappable RAID/ Dual Hard Drives ..................................................................... 10 PoweredUSB Ports / Power Port................................................................................... 10 UPS ............................................................................................................................... 11 Printer Power Port ......................................................................................................... 11 Cooling System ............................................................................................................. 11 Fan-Off Mode ............................................................................................................... 11 Versatility ...................................................................................................................... 11 System .............................................................................................................................. 12 Configurations ............................................................................................................... 12 Processor Support ......................................................................................................... 12 Processors currently supported on the 680 ................................................................... 13 I/O Ports ........................................................................................................................ 14 Off / On Button ............................................................................................................. 14 Hard Disks .................................................................................................................... 15 Zero Bezel Touch Screen .............................................................................................. 15 System Board ................................................................................................................ 16 LCD Display ................................................................................................................. 16 Secondary Video Port(s) ............................................................................................... 16 Serial ports .................................................................................................................... 18 PoweredUSB Ports ........................................................................................................ 19 Kensington Security Slot .............................................................................................. 20 Audio ............................................................................................................................. 21 Printer Power Port ......................................................................................................... 21 Cash Drawer Port .......................................................................................................... 22 CMOS Clear .................................................................................................................. 24 Power Supply ................................................................................................................ 24 Typical Power Consumption 680 .................................................................................. 25 Service .............................................................................................................................. 26 Removing the Head from the Base ............................................................................... 26 Removing the Power Supply ........................................................................................ 27 VESA Mounting ........................................................................................................... 28 Optional Wall Mount Bracket Installation .................................................................... 29 Removing the Back Cover ............................................................................................ 30 Changing the System Board .......................................................................................... 31 Adding Memory ............................................................................................................ 33 Changing the Processor ................................................................................................. 33 Accessing the HDD/SDD Drives .................................................................................. 34 J2 680 System Manual Version 1.0 May 11, 2012 3 BIOS Setup ...................................................................................................................... 35 Entering the BIOS Setup ............................................................................................... 35 Main, System Overview ................................................................................................ 35 Advanced Settings ........................................................................................................ 36 Launch PXE ROM ........................................................................................................ 36 SATA Configuration ..................................................................................................... 37 Peripheral Power and LCD Brightness Configuration .................................................. 38 Power Configure Screen ............................................................................................... 39 Restore on AC Power Loss ........................................................................................... 39 Wake on LAN ............................................................................................................... 39 RTC Configuration ....................................................................................................... 39 Boot Settings ................................................................................................................. 40 Display OEM Logo ....................................................................................................... 40 Exit Options .................................................................................................................. 41 Driver Installation, Windows ......................................................................................... 42 Chipset Driver Installation ............................................................................................ 42 Graphics Driver Installation .......................................................................................... 42 Audio Driver Installation .............................................................................................. 43 LAN Driver Installation ................................................................................................ 44 Multi-Touch Projected Capacitive Touch Driver ......................................................... 47 Optional Multi-Touch Projected Capacitive Touch Driver .......................................... 49 OPOS drivers ................................................................................................................ 51 J2 Health .......................................................................................................................... 52 Installation ..................................................................................................................... 52 Tray Icon ....................................................................................................................... 52 Logging to File .............................................................................................................. 53 Registry Entries ............................................................................................................. 54 J2 Remote Monitoring Software ................................................................................... 54 SMI BIOS Info Utility .................................................................................................... 55 Installation ..................................................................................................................... 55 Operations ..................................................................................................................... 55 Cash Drawer Test Utility ................................................................................................ 56 Installation ..................................................................................................................... 56 Operation ....................................................................................................................... 56 J2 Virtual Serial Ports Drivers ...................................................................................... 57 RAID ................................................................................................................................ 58 RAID Overview ............................................................................................................ 58 AHCI ............................................................................................................................. 58 Enabling RAID in the BIOS ......................................................................................... 59 RAID Volume Creation ................................................................................................ 59 J2 680 System Manual Version 1.0 May 11, 2012 4 F6 Installation Method .................................................................................................. 59 Installing the Intel Matrix Storage Manager Software ................................................. 60 Hot Swapping RAID 1 drives ....................................................................................... 60 Packing List ..................................................................................................................... 63 Standard Items .............................................................................................................. 63 680 Optional Peripherals ................................................................................................ 64 MSR .................................................................................................................................. 64 Overview ....................................................................................................................... 64 Installing the 680 MSR ................................................................................................. 65 Customer Display ............................................................................................................ 67 Overview ....................................................................................................................... 67 Secondary Video Display ................................................................................................ 67 Fingerprint Reader / MSR ............................................................................................. 68 iButton / MSR .................................................................................................................. 68 680 UPS ............................................................................................................................ 68 RFID ................................................................................................................................. 68 Wall Mount Bracket ....................................................................................................... 68 Pole Mount Options ........................................................................................................ 68 5 J2 680 System Manual Version 1.0 May 11, 2012 The J2 680 is the second generation of very high performance integrated Point of Sale computer from J2. Built on the features and capabilities for the J2 650 the J2 680 offers even higher performance and expanded I/O. The J2 680 retains all the versatility of previous generation system and adds Quad core processor options, expanded I/O support with PoweredUSB, Intel remote management, HDMI video, Multi-Touch, Zero Bezel design and retains RAID and other important feature of the previous generation. This integrated touch screen computer like most J2 designs features an design, which means it can be used as a counter top unit, a wall-mount or a pole-mounted computer. In this one small package you have the highest speed available intergraded or non-intergraded POS computer currently available. The J2 680 comes standard with an Intel 2.4GHz Dual Core Sandy Bridge processor but can also be order with a number of other processors including the very high end Intel i7 3.4GHz Quad Core processor. The J2 680 system board uses the Intel LGA1155 socket and supports a wide range dual and quad core processors. Using the Intel Sandy Bridge processor with the Q67 chipset the J2 680 uses the latest high performance desktop solution in a very small footprint system. This solution provides for very high performance but with a very low carbon foot print. The Sandy bridge chipset is design only to draw as much power as need for any given operation greatly reducing the average power consumption for this level of performance. Designed for easy machine maintenance and upgradeability, the following is a list of important 680 features:
1. Upgrades to the memory modules can be easily done by simply removing four screws on the back cover. 2. A complete motherboard upgrade can be carried out in less than 1 minute. 3. The two quick change SATA hard disk drives are easily accessible, housed on a slide-in drive bay that allows the drives to be hot swappable. 4. The footprint of the J2 680 is particularly compact making it ideal for the space conscious retailer. The 680 supports the standard Microsoft operating systems, Windows 7, POSReady 7, Windows 7 Embedded, XP, POSReady 2009 and XP embedded. The 680 is equally proficient with the many flavors of Linux. J2 680 System Manual Version 1.0 May 11, 2012 6 J2 680 System Manual Version 1.0 May 11, 2012 7 Main board CPU Support Chipset Intel Sandy Bridge Desktop Processors, socket LGA1155 Intel Celeron Dual Core G530 up to Quad Core i7- 2600 3.4GHz Q67 System Memory 2 x 240-pin DDR3 DIMM 1333/1667MHz sockets - up to 16GB Graphic memory Share system memory 8MB~256MB BIOS LCD Size Brightness Resolution AMI LCD Touch Panel 250 nits, adjustable in 8 steps to 25nits 1024 x 768 Touch Screen Multi-touch Project Capacitive or True Flat Resistive 5 wire Tilt Angle HDD/SSD USB Serial 0 ~ 90 Storage Two 2.5 inch SATA 3.0 drives support for HDD or SDD RAID 0 or 1, Quick Change-hot swap 160GB HDD or 16GB SSD standard External I/O Ports 6 total 2.0, 5 in cable well, 1 on side, 3 are PoweredUSB Four DB9 RS-232 with power option PoweredUSB 2 +12V PoweredUSB and 1 +24V PoweredUSB LAN 2nd Display Cash Drawer Power In Audio Jack Printer Power Power LED 10 /100/ 1000 Intel 82579LM Controller One VGA port and One DisplayPort DisplayPort supports HDMI and DVI displays 2 x RJ 11 24V with status 19VDC 9.47 amps One headset, one microphone-in
+24 V 2.5 amps, supports most 24V POS printers Front bezel, green for on, amber for standby J2 680 System Manual Version 1.0 May 11, 2012 8 Power Adapter 19VDC, 180W, 100-240 VAC,50~60Hz, 2.5A Power MSR iButton Optional Peripheral 3 Track Dallas Key iButton Fingerprint Reader USB Digital Persona Fingerprint Reader RFID 2-in-1 2-in-1 Second Display Customer Display UPS 125KHz RFID USB MSR 3 track / Finger Print MSR 3 track / iButton 4:3 displays, with or without touch 2x20 VFD DC UPS, 0.5-1.5 hours run time Mounting Standard Optional Counter Top Base, Adjustable Viewing Angle 0-90 100mm VESA mounting point Pole Mount, Adjustable angle VESA, Swing-arm Mounts, others EMC & Safety Operating Temperature Storage Temperature Operating Humidity Storage Humidity Dimensions
(W x D x H) Weight OS Support Environment FCC, Class A, CE, LVD 0 ~ 40
-20 ~ 55 20% ~ 80% RH non-condensing 20% ~ 85% RH non-condensing 370 x 250 x325mm 8.1kg Windows 7, POSReady 7, Windows 7 Embedded, XP, POSReady 2009, XP Embedded, version of Linux
* This specification is subject to change without prior notice. J2 680 System Manual Version 1.0 May 11, 2012 9 LGA 1155 desktop processors and chipsets, code named By using the latest Sandy Bridge, the J2 680 supports a very wide range of processors. By taking advantage of J2 computer designs, we are able to combine features of all three for an optimal POS system design. The result is a POS system that can utilize a desktop chipset that draws very little power and generates a low amount of heat, similar to mobile chipsets and processors. Notebook quality components are used in the processor, chipset, and power supply circuit, which allows for reduced heat generation and minimal power usage. Additionally, the 680 takes full advantage of the low power features built into the Intel processor and chipset to further reduce heat.
, and POS Hot Swappable RAID/ Dual Hard Drives Like the J2 650, the first integrated POS system on the market to offer a hot swappable RAID feature the J2 680 also supports this feature. The two internal 2.5 inch SATA hard drives can be configured as a RAID array which gives true fault tolerance to the hard drive subsystem. PoweredUSB Ports / Power Port Addressing the need for additional power ports the J2 680 supports two +12V and one
+24V PoweredUSB ports. The J2 680 can take advantage of growing availably or PoweredUSB products on the market. In addition to the three PoweredUSB port the J2 680 also support four powered serial ports, and VGA +12V power, a +24V printer power port and 3 standard 2.0 USB ports. By using a combination of these powered ports most all additional external power supplies for devices like display and other can be eliminated. This save space and reduces cost, cables and powered consumption. Also in most installs this means only one AC power point is needed. In additional with J2 optional UPS all these devices will be powered during a power outage. J2 680 System Manual Version 1.0 May 11, 2012 10 UPS Not your ordinary UPS, the J2 680 UPS is a DC, not an AC UPS. The UPS fits conveniently into the base of the unit. Unlike an AC UPS the J2 UPS makes the 680 work more like a notebook computer. In addition to running the 680 for up one hour, the UPS will run all the POS peripherals attached to the 680, including the printer. Because of the unique design of the J2 UPS and power supply, the need for special AC power conditioning devices is eliminated. Printer Power Port The 24 volt Printer Power Port can power most POS printers on the market, including the popular Epson line of printers. When used along with the J2 UPS, if a power outage should occur, the POS terminal can still operate and print receipts for up to one hour. Also, when the 680 is turned off the printer is turned off also. This is very useful when the auto power on and off features of the 680 is used. This also applies to the +24V PoweredUSB port (note, only one +24V port can be used at a time). Cooling System Great attention was paid to the thermal solution of the 680, it is truly a unique feature. The 680 can run as a fan less or fan-cooled system. Because of the very wide range of processors supported, thermal loads can range from 5 watts to as high as 95 watts. The 680 was designed to handle these thermal loads while still being super quiet. Two smart fans are used in conjunction with an Embedded Controller (EC) to ensure that the fans run at the lowest possible speed while still providing proper cooling. Fan speed changes are controlled to produce the smallest acoustical signature possible. The 680 fans are the type used in Blade Servers and have a speed range from 3500~10,000 rpms at very high torque. Fan-Off Mode When using the i5 or lower performance processor the 680 can run in a fan-off configuration. In the mode the 680 is a fan-less convection cooled device. This fan less operation may be required for high dust or other special environments. This feature is uniq
-
Versatility The word versatility is very much over used, but it is the correct word to describe the most unique feature of the 680. The combination of all the 680 unique features allows for the 680 to fit many roles. The 680 is not just one product, but a full product range all in one system. From fan less thin client to Quad Core RAID Server - the 680 does it all. J2 680 System Manual Version 1.0 May 11, 2012 11 Configurations The 680 can be ordered or upgraded to many possible configurations. Selecting the right combination of memory, processor, hard or solid state drive(s), and software drivers can dramatically change the performance of the 680 system. For a lot of users the standard 530 2.4GHz dual core processor and 2GB of memory is fine, as this is already more powerful most all POS systems, but some applications may require more horse power. In this case the J2 680 could be configured with a quad core i5 or i7 processor. J2 will be happy to help you determine what you may require from the 680 in the most cost effective way. More memory may be added to get the performance needed, or sometimes a quad core processor and dual HDD with RAID are needed. The 680 can do it all, low end to high end. Processor Support The 680 supports a very wide range of Intel processors. Each provides a different price performance level. From Celeron dual core, Pentium dual core and -3, i5 and i7 dual a quad core with processor speeds from 2.4GHz to 3.4GHz are all supported by the 680. The 680 comes standard with the Intel dual core 2.4 GHz G530 processor but can be ordered with a different processor type. The processor can be easily upgraded by a qualified technician. The 680 uses the Intel defined LGA1155 socket. Intel is constantly adding new processors so please check with J2 for any additions since publication of this manual. The large heat sink, cooling fans, and fan controller (shown below) are designed to keep everything running cool, quiet, and reliably with the supported processors. System Board, back view J2 680 System Manual Version 1.0 May 11, 2012 12 Processors currently supported on the 680 I/O Ports Most I/O ports are accessible in the cable well at the bottom of the unit. A cover plate is provided to cover the cables. I/O Panel Off / On Button The Off /On button is located in the cable well, as shown. This button is located near the side to prevent accidental powering down by the user. The function of the button can be controlled by the OS. If the 680 hangs for some reason it can always be powered off by holding the Off / On button in for six seconds. The 680 also supports the following: Restore on AC on power loss, Wake On LAN, and Wake On RTC alarm features to control the system power up. Off / On button Location Hard Disks Two 2.5 inch SATA hard drives (HDD) or solid state drives (SSD) are supported. These drives can be configured as standard hard drives or as a RAID array. The SATA interface can support data transfer rates up to 6.0 Gb/s and supports AHCI and Hot Swapping of hard drives. The HDDs can easily be accessed by removing a panel on the left side of the unit. HDDs can be installed or removed in seconds by removing one screw. A carrying tray (two of which are supplied with the 680) fits onto a new drive without tools. The drive can now easily be slid into the drive bay. In a RAID 1 configuration a drive can be hot swapped, removed, or inserted with the power on (see section on RAID setup). HDD access panel HDD slide in-slide out drive bay Zero Bezel Touch Screen This The 680PTC unit uses a Multi-Touch Projected Capacitive technology touch screen
(PCT). The PCT touch screen has no known failure mode-- it does not wear out. screen is made with tempered glass and does not reduce the brightness of the LCD panel. When operating in a very high use environment PCT is the recommended touch screen technology. The PCT touch screen will work with most gloves and stylus designed to work with tablet computers. The screen has a smooth glass surface that is reflective. The 680TFR uses a five-wire touch screen rated at 35 million touches per point. The resistive technology is very responsive and is the traditional choice for a hospitality POS system. The screen has an anti-reflective plastic film surface. Both screens are fully spill proof, dust proof and can be cleared with and standard glass cleaner. The zero bezel, sometimes called true flat, design allow for this plus easy cleaning. The 680 touch screen was designed to easily be changed, normally in less than two minutes. Depending on operating environment and usage, both the Resistive and PCT touch screens have strengths and weaknesses. J2 offers both touch screen technologies on the 680. J2 680 System Manual Version 1.0 May 11, 2012 15 System Board POS computers typically have a desired lifespan of 10 years or longer, therefore product quality is of the utmost importance. The 680 electronics are built with high-end components to ensure reliability and long lasting product performance. The system board is designed for quick replacement and only has one connection, an edge pin connector, to which all motherboard connections are made. System board LCD Display The LCD display for the 680 is a 1024 x 768 resolution display with 16.2 Million colors. The brightness is rated at 250cd/m2. The Intel controller allows for the display to be rotated to 0, 90, 180 or 270 degrees without loss of performance. The LCD brightness can be controlled in 8 steps, from 250 cd/m2 to 25 cd/m2. The brightness can be set to a fixed level in the BIOS or controlled by a utility supplied by J2. Secondary Video Port(s) A standard PC VGA video port is supported on the 680 and can be set as the primary or secondary display The VGA video port has an industry standard HD DB15 connector. When used with some J2 monitors the display can be powered by the 680 through this connector. J2 680 System Manual Version 1.0 May 11, 2012 16 The 680 also supports the newer digital video standard DisplayPort connector. This connector supports a DisplayPort monitor or a HDMI display or DVI monitor. When used with HMDI or DVI display a passive adapter cable is used. When used with a HDMI display Audio is support via the same HMDI cable. The secondary video displays can be configured as a Twin, Intel Dual Display Clone, or Extended Desktop. Most all monitor resolutions from 640 x 480 to 2560 x 2048 are supported. Note that only one external video display is support at a time, either on the VGA video port or the DisplayPort video port. VGA and DisplayPort Video Ports J2 680 System Manual Version 1.0 May 11, 2012 17 Serial ports The 680 has four external RS232 serial ports, all of which can be powered. The serial ports are standard RS-232 ports with a DB9 male connector. The serial ports, in a normal configuration, are mapped to COM 1-4. There also four internal serial ports one of which is used for the resistive touch controller and the other are reserved for other internal options. COM ports 1-4 can supply power to an external device when required, like the optional J2 Customer Display. COM 1 can supply +5 volt and COM 2-4 supply +12 volts. The voltage is supplied on pin 9 (RI) of the DB9 connector. The maximum current is 1000ma and is over-current protected. A BIOS setting is used to enable the voltage on each port. J2 does not normally recommend using the +5 volt option on COM 1 and is only there for some legacy devices. The problem is it easy for +5 volt device to be plugged into a +12 enable serial port by mistake which will burn out the +5 volt device. A good alternative to powering a +5 volt serial device, or any +5V device would be to use power from an unused USB port. Cables for this are readily available (see below). DB9 pin out serial ports Serial Port Pin RS232 1 DCD 2 3 4 5 6 7 8 9 RD TD DTR GND DSR RTS CTS RI USB to +5V cable J2 680 System Manual Version 1.0 May 11, 2012 18 USB Ports The 680 has six external and 4 internal USB 2.0 ports. Of the six external ports (see below) five ports are located in the cable well and one is located on the left side of the unit for easy access. The four internal USB ports are as follows: one can be used for the optional Finger Print Reader and is located on the MSR connecting point. The second internal USB port is used for the PCT touch screen controller and the other internal USB ports is designed for other optional internal devices. All the J2 680 USB ports can supply 1000ma of power, 500ma more than the normal for the USB specification. PoweredUSB Ports Of the 6 external USB 2.0 ports 3 are PoweredUSB ports. Located in the cable well are two +12V PoweredUSB ports and one +24V PoweredUSB port. These ports conform to the PoweredUSB standard. It should be noted that these three ports can also be used as standard USB ports as well. Normal +5 USB devices will plug into the bottom half of the connector without a problem. USB Ports Side USB Port J2 680 System Manual Version 1.0 May 11, 2012 19 Ethernet Connection The 680 uses the Intel 82579LM Gigabit Ethernet controller. The Ethernet connector is located in the cable well, as shown below. The Ethernet controller supports Wake on LAN, the BIOS supports a PXE boot ROM as well. There are two LEDs on the LAN connector: the Green LED lights up when the LINK signal is present and the Amber LED lights comes on when there is LAN activity. This Ethernet supports Intel AMT feature when used with the correct processor. Ethernet Connector Kensington Security Slot There is a Kensington Security Slot (lock slot) on the 680. (Please see below). It is located on the head in the cable well. The Kensington locks are normally used as a deterrent to prevent opportunistic theft. Most retail locks will work with the 680, however please check to see if a lock fits, as not all do. Kensington slot Cable Well J2 680 System Manual Version 1.0 May 11, 2012 20 Audio The 680 uses the VIA1708B HD audio controller. There is one internal speaker. Both a microphone jack and a headset jack are located in the cable well of the 680, as seen below, which allows for the connection of a microphone and headset or audio out to other devices. Audio is also output via the HDMI port when used. Audio Jack Location Printer Power Port The Printer Power Port allows an industry standard POS printer to be powered from the 680 and eliminates the need for a separate external power supply for the printer. The Printer Power Port supplies 24 VDC 2.5 amps and 6.0 amp surge current which will run most POS printers on the market. The power cable for this port is supplied standard with the 680 unit. The Printer Power Port will also supply power to a printer even when running on the optional UPS. When the 680 is powered down, then power to the printer is turned off. This same power circuit is used by the +24 PoweredUSB port and normally only one +24V device is supported at one time. Printer Power Port Printer Power Port Cable J2 680 System Manual Version 1.0 May 11, 2012 21 Cash Drawer Port The 680 is equipped with one Cash Drawer port that will support one or two drawers. This port is located in the cable well and uses the industry standard RJ-11 connector and pin out (illustrated below). This pin-out is the same as used by EPSON printers and cables for the EPSON printer normally work with the 680. Cash Drawer Ports Cash Drawer 1 Pin Assignment 6 1 Pin 1 2 3 4 5 6 Signal GND CD1 SOLENOID STATUS / STATUS CD1 24V CD2 SOLENOID GND / STATUS CD2 The application may address the Cash Drawer port in two ways:
1) Using the J2-supplied OPOS drivers for Windows. 2) Direct access to the I/O ports 3) J2 supplied Virtual Serial Cash Drawer Emulator J2 680 System Manual Version 1.0 May 11, 2012 22 Cash Drawer Controller Register The Cash Drawer Controller use one I/O address to control the Cash Drawer. Register Location: 48Ch Attribute: Read / Write Size: 8bit BIT BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 Read Attribute 7 6 5 4 3 2 1 0 X X X X X on Epson printers. Reserved Write Reserved Reserved Cash Drawer 1 fire Cash Drawer 2 fire Reserved Cash Drawer 1 status Reserved s on the one RJ-11 is the same as is used J2 680 System Manual Version 1.0 May 11, 2012 23 CMOS Clear The 680 CMOS can be cleared jumping JP3 pin 1-2 then removing the jumper. Power Supply The 680 uses a notebook type power supply that is normally mounted in the base of the unit. The power supply is rated with an output of 180 watts 19 VDC 9.47 Amps and has an input rating of 100-240VAC at 50~60Hz 2.5Amps maximum. The power supply has an efficiency rating IV. The power supply connector is a four pin locking type that plugs into the system s power input connector located in the cable well. Power Input connector J2 680 System Manual Version 1.0 May 11, 2012 24 Typical Power Consumption 680 ssors and chipset allows for much lower 220VAC 50Hz, measured voltage 236 VAC POSReady 7 The typical power consumption of the 680 is lower that most desktop computers. Using the latest power consumption than previous generations of POS computer. This when coupled with proper system configuration can greatly reduce the systems total carbon foot print. Test conditions Voltage:
OS:
Heavy Load Program: PassMark BurnInTest defaults values Maximum load:
Temperature:
All system where tested in there standard hard drive configuration. Results are +/- 15%. J2 680 G850 2.9GHz Pentium 1: Normal application including most POS software 2: Very heavy load application 3: Maximum load 4: Normal POS app, back light off 5: Standby, unit off, waiting for wake on LAN, RTC or power button >4 watts PassMark BurnInTest Max CPU Temp 26c 40 watts 57 watts 64 watts 20 watts J2 680 System Manual Version 1.0 May 11, 2012 25 Removing the Head from the Base The 680 is shipped with a counter top base which allows for the head to be adjusted from 0-90. To remove the integrated head from the base, fully loosen the thumbscrew located on the back of the unit under the hinge of the counter top base, as shown below. Then lift the head as illustrated:
Loosen Thumb Screw Slide Head up to remove J2 680 System Manual Version 1.0 May 11, 2012 26 Removing the Power Supply The power supply is normally located in the counter top base. When using a wall mount bracket or the J2 UPS, the power supply would be external from the unit. To remove the power supply from the base, three screws needs to be removed as shown. Screw locations J2 680 System Manual Version 1.0 May 11, 2012 27 VESA Mounting The 680 unit also supports the industry standard 100mm VESA mounting. The same mounting hard point used for the counter top base is used for VESA mounting. The four point that thread holes for 4mm screws. 100mm VESA Pattern Threaded Mounting point(s), 4mm screw J2 680 System Manual Version 1.0 May 11, 2012 28 Optional Wall Mount Bracket Installation The wall mount bracket has threaded mounting holes (screws provided) for the 75mm VESA standard; and unthreaded holes for the 100mm standard. Using the 100mm hole pattern the bracket can be used by itself as a wall mount bracket. After installing the thumbscrew clip mount bracket to the wall, hang the J2 680 on the bracket. Install screw to secure thumbscrew clip The bracket slides on to the J2 680 mount posts, as shown. Normally the bracket would already be mounted to the wall or a VESA mount and the 680 would be hung on the bracket. Once in place the thumb screw would be tightened. J2 680 System Manual Version 1.0 May 11, 2012 29 Removing the Back Cover The following steps show how to disassemble the 680 for servicing:
On a clean, protected surface, place the unit screen-side down. Remove the four cover screws as shown. Carefully lift the back cover as shown. Remove four screws where shown Carefully tilt up the back cover to remove Note: The 680 was designed so that the internals of the unit could be accessed without having to remove the mounting base or the mounting bracket of the unit. J2 680 System Manual Version 1.0 May 11, 2012 30 Changing the System Board
*Special Note: An anti-static workplace with proper grounding is required when changing the System Board. First remove the back cover. There are 3 screws that hold the system board in place that will need to be removed. (see photo below) Three screws to remove System Board J2 680 System Manual Version 1.0 May 11, 2012 31 After the screws are removed the system board can be unplugged from its connector. While using the I/O bracket to pull on, slide the board out towards the bottom of the unit as shown. When reinstalling the system board make sure the locking tabs on the bottom of the board lock into their mating slots. J2 680 System Manual Version 1.0 May 11, 2012 32 Adding Memory Note: An anti-static workplace with proper grounding is required when adding memory. Remove the back cover. You can now access the two memory sockets, the order in which the memory is populated does not matter. The J2 680 supports up to 16GB of memory in two sockets. Memory type is 240 DIMM DDR3 1066/1333. Memory sockets Changing the Processor To change the processor, first start by working in an anti-static workplace with proper grounding. Remove the back cover by removing the four screws; now remove the black plastic fan duct. Loosen the four spring-loaded screws that secure the processor heat sink by loosening. Each screw about two turns at a time so that the pressure is removed from the socket evenly. Once the screws are free you will now be able to remove the heat sink. It will stick because of the heat sink compound, so take care to move it gently from side to side until it comes off. Set the heat sink aside, top side down. You can now remove the processor from the socket. Push the locking lever down, push out from the locking tab, and move up as shown. Now carefully lift the cover up and you can remove the processor. **Be sure only to touch the edges of the processor and do not touch the processor pads of the socket pins. These socket pins are very easy to bend and damage to the socket
. J2 680 System Manual Version 1.0 May 11, 2012 33 Accessing the HDD/SDD Drives Remove cover screw then remove cover Remove or insert drive as needed The HDD/SSD may be hot swapped when in a RAID 1 configuration. In non-RAID 1 configurations the unit should be powered down before changing a drive or data may be lost. No physical damage will happen to the HDD if inserted or removed with power on. J2 680 System Manual Version 1.0 May 11, 2012 34 Entering the BIOS Setup To enter the BIOS Setup, turn on or reboot the 680 and press the DEL key after the BIOS sign-on screen appears. The main menu of the BIOS setup will be displayed, this can take a few seconds. If the supervisor password is set, you must enter it here. The area on the right side of the screen displays a help window for the current screen or BIOS option. BIOS setting should only be change by qualified personal as changing some setting can cause the system not to function properly. Main, System Overview In this screen the system time and date are displayed and can be set. The time and date can also be set through the OS. This screen also displays the BIOS version (project), BIOS Build Date, CPU type, CPU speed and DRAM memory size, Product type, System Serial Number and mother board revision. The serial number of the mother board and the system are the same. Main screen J2 680 System Manual Version 1.0 May 11, 2012 35 Advanced Settings This menu contains settings to control a number of system functions. Most these settings are self-explanatory. Advanced Setting Screen Launch PXE ROM This setting enables the built- in PXE LAN remote boot rom. This allows the system to run as a diskless workstation, or to be able to download a drive image to a blank drive. When enabled, a message screen will appear and Shift-F10 can be typed to access the PXE ROM options. J2 680 System Manual Version 1.0 May 11, 2012 36 SATA Configuration In this screen the SATA hard drives can be set to work in one of three modes, SATA, RAID or AHCI. When set to SATA, the SATA drive works the same as a normal IDE HDD. This is the IDE compatible mode and default BIOS setting. The other two selections are RAID and AHCI modes. Please see the separate section in the manual for RAID Setup for further information on using RAID and AHCI modes. SATA Configuration Screen J2 680 System Manual Version 1.0 May 11, 2012 37 Peripheral Power and LCD Brightness Configuration This submenu allows for the enabling of power for the serial ports, default cash drawer pulse timing and default LCD brightness level and power for a J2 supplied VGA port monitor. Power enable for serial Ports LCD Brightness Setting J2 680 System Manual Version 1.0 May 11, 2012 38 Power Configure Screen Power Configure Screen Restore on AC Power Loss The 680 has three options should AC power become lost and then restored. There is Power Off (stay turned off), Power On (turn on when AC restored), or Last State. The Last State setting will cause the unit to turn on if it was on when AC power was lost or it will stay off if the unit was off when AC power was lost. Wake on LAN Wake on LAN is enabled by default but can be disabled in this screen. RTC Configuration The RTC has an alarm function that can be used to turn the 680 on at a preset time of day. This function is enabled by this setting. The wake up time can also be set here. J2 also has available a utility to set the wake-up time from Windows. This is more versatile than the BIOS setting as it allows for more than one time of day to be set as well as days of the week to turn on. J2 680 System Manual Version 1.0 May 11, 2012 39 Boot Settings If more than one bootable device is in the system the boot order can be set in this menu. If a bootable USB storage device is plugged in at boot up the 680 will boot from that device by default. If this is not desired the boot order can be changed here. A list of detected drives will be displayed with the current boot order. Boot Settings Screen Display OEM Logo The BIOS can display two types of OEM logos on boot up. The default is a small J2 logo in the upper left hand corner. With this setting BIOS POST test messages can be seen during boot up. The second type which is enabled by this entry is a full screen J2 logo. When this logo is selected the BIOS POST messages cannot be seen. The BIOS setup can still be entered by typing the DEL key a few seconds after the logo appears. Customer logos can replace the J2 logos when required. Please contact J2 regarding this, if required. J2 680 System Manual Version 1.0 May 11, 2012 40 Exit Options After making any changes to the BIOS settings, the changes can be saved from this screen. Any changes can be discarded as well or the factory BIOS defaults can be loaded. Typ setting to the factory defaults. It should be noted that to save changes to the BIOS setup the F10 key can be typed from any screen to save the BIOS changes. It is not necessary to exit setup from this screen. To discard any BIOS setup changes you can type the ESC key from any screen to exit. Exit Options Screen J2 680 System Manual Version 1.0 May 11, 2012 41 Chipset Driver Installation The chipset driver is needed to get the full potential from the 680 chipset. It should be loaded before other drivers and first thing after booting. The drivers can be downloaded from the J2 web site:
http://www.j2retailsystems.com/support/680/Chipset/. After extracting the drivers to a temporary folder, run Setup. Just answer Next or Yes to all the screen prompts and the drivers will install. Graphics Driver Installation You can download the 680 graphics driver from the J2 web site at:
http://www.j2retailsystems.com/support/680/Graphics/. This is an .exe file so just run it and answer Next or Yes to all screen prompts and the drivers will install. The last screen will ask if you want to reboot, answer Yes. J2 680 System Manual Version 1.0 May 11, 2012 42 Audio Driver Installation The Audio Drivers can be downloaded from the J2 web site at:
http://www.j2retailsystems.com/support/680/Audio/. After extracting the driver to a temporary folder, run Setup, and then follow the instructions below:
First Audio setup screen Just click on Next to install the Audio driver. Second Audio setup screen Check the Codec Driver box, and then click Next. Answer Next to any more dialog boxes, then Finish. The system will need to be rebooted before the audio drivers take effect. J2 680 System Manual Version 1.0 May 11, 2012 43 LAN Driver Installation The LAN drivers can be downloaded from the J2 web site:
http://www.j2retailsystems.com/support/680/LAN/. After extracting the driver to a temporary folder, run Setup. Just answer Next or Yes to all the screen prompts and the driver will install. LAN driver install screen J2 680 System Manual Version 1.0 May 11, 2012 44 Resistive Touch Screen Driver Installation The Touch Drivers can be downloaded from the J2 web site at:
http://www.j2retailsystems.com/support/680/Touch/. When run, the diver will display a welcome screen, at this point just press next for the next few screens. When you get to this screen check both RS232 and USB options and click next. Just click till this screen and then click next and the driver will finish installing. J2 680 System Manual Version 1.0 May 11, 2012 45 Click finish at the screen. The driver will then detect the port the touch screen is on
(normally COM6) then ask you to reboot the system. After rebooting the touch should be working. Calibration is not needed as this is done at the factory. J2 680 System Manual Version 1.0 May 11, 2012 46 Multi-Touch Projected Capacitive Touch Driver No touch driver needs to be loaded for the PCT touch screen because it uses the Microsoft built in pen and touch driver, No calibration is needed for the projected capacitive touch screen. The driver options can be accessed via the Windows control panel. The built in Windows pen and touch driver is present in XP, Vista and all versions Windows 7. The first page of options allows for the change how your finger or stylus interacts with the screen. The sensitivity and function of touch to the screen can be changed here. J2 680 System Manual Version 1.0 May 11, 2012 47 The other four option tabs are shown below for reference. They are self-explanatory in most case and additional information can be obtained through the Windows help function. J2 680 System Manual Version 1.0 May 11, 2012 48 Optional Multi-Touch Projected Capacitive Touch Driver In addition to the Windows built in standard touch driver J2 also supplies and optional touch driver that is used when multi-monitor touch support is needed. This driver works with Windows XP and later version of Windows. The driver can be downloading from J2 web site. To install just extract the zip file where you wish to run it from and run setup. When asked to install PS/2 or RS-232 driver answer no, the PCT controller is a USB device. When the install is complete it will ask if you wish to do a 4 point calibration, answer no to this as the PCT screen does not need calibration. The touch will now be working. The PCT touch configuration utility can be found in programs under eGalax Touch, Configuration Utility. This program allows for the configuration of the touch screen option. s the current version of the touch screen plus has a link to the touch here the latest version of the driver can be found. A copy monitors. J2 680 System Manual Version 1.0 May 11, 2012 49 the touch on beep, double click function and right mouse button emulation. for a PCT screen. A draw test is provided to verily the operation and calibration of the touch screen. The J2 680 System Manual Version 1.0 May 11, 2012 50 OPOS drivers The OPOS driver for the 680 supports the Cash Drawer ports, the optional MSR, the optional 2x20 character Customer Display, and the optional iButton reader. The OPOS driver may be downloaded from the J2 web site at:
http://www.j2retailsystems.com/support/680/. Just run the OPOS setup.exe file to install. J2 680 System Manual Version 1.0 May 11, 2012 51 J2 has a standard program that works with all its POS products, called J2 Health. This program is used in either a standalone mode or in conjunction with J2 remote monitor/asset tracking software. The J2 Health program monitors different aspects of the POS hardware to ensure the hardware is running within specification. For the J2 680 it monitors critical system voltages, as well as system and CPU temperatures. Installation The utility can be downloaded from the J2 web site:
http://support.j2rs.com/Utilities/Health/ To install just unzip anywhere and run setup. Like other J2 utilities it can be uninstalled through the Windows control panel. Tray Icon Once installed and the system has rebooted, J2 Health will be running in the background. The J2 health icon will appear in the task bar tray:
Right-clicking on this icon displays different Health options, shown below:
A sample screen is shown below:
J2 680 System Manual Version 1.0 May 11, 2012 52 As can be seen above, when running on the J2 680 the J2 Health program displays critical system voltages and system and CPU Core temperatures. For other J2 POS systems, J2 Health may display more or less information. An example would be the J2 680 unit, which in addition to the above information would also display the fan speed of the two J2 680 fans. Logging to File The J2 Health program can log the health data to a file in the csv text format for related problems. When logging is enabled, the tray icon Rx symbol will change to red to indicate logging in is taking place. J2 680 System Manual Version 1.0 May 11, 2012 53 Registry Entries The J2 Health program creates registry entries for the different health values. Dynamic values are updated at the user defined interval, which is by default 5 seconds. Other software may use these registry entries to access the J2 health information. J2 680 Health keys are shown below:
J2 Remote Monitoring Software J2 now offers a full remote monitoring and asset tracking solution that works in conjunction with J2 Health to ensure the highest uptime possible of your POS hardware. Please contact J2 sales for more information on this fully customizable, remote monitor solution. For more information, please visit us at http://www.j2retailsystems.com/newsarticle.php?news_id=57 J2 680 System Manual Version 1.0 May 11, 2012 54 The J2 SMI BIOS Info program allows for the reading of all populated BIOS DMI/SMI information. With some J2 products including the J2 680, this information also includes dynamic system health information. Normally this dynamic DMI health information BIOS is only supported on very high end servers. Now J2 brings this feature to POS hardware. The J2 SMI BIOS Info program will run on any J2 POS hardware or for that fact on any PC hardware. It can display all DMI/SMI information on a formatted form. Installation The utility can be downloaded from the J2 web site: http://support.j2rs.com/Utilities/
To install just unzip anywhere and run as you wish to run the utility form. Operations Just click on the .exe file to run. The following screen will be displayed (see below). Note that the health data will only display on newer J2 systems that support the dynamic DMI health BIOS. J2 680 System Manual Version 1.0 May 11, 2012 55 J2 has a generic cash drawer test utility that works on all J2 products, including the new J2 680 computer. Installation The utility can be downloaded from the J2 web site: http://support.j2rs.com/Utilities/
To install just unzip anywhere and run as you wish to download the utility form. Operation etting to test the cash drawer(s). (see example below) virtual serial ports program. The virtual serial port program must be installed with the cash drawer virtual serial ports set to Comm 10 & 11. J2 680 System Manual Version 1.0 May 11, 2012 56 Virtual serial ports can be used for the cash drawers, virtual 2x20 line display on the optional 10.1 LCD, Smart UPS, MSR and iButton. To open virtual serial cash drawer send a bell character to the Com port it is assigned too. the drawer may be obtained by reading the status bits of its COM port. The drawer open/close status will be reflected on the CTS and RI bits, either bit may be used. This virtual COM port driver is designed to work the same as a hardware serial cash drawer and will work with drivers for serial cash drawers. J2 680 System Manual Version 1.0 May 11, 2012 57 RAID Overview The 680 uses the Intel Matrix Storage Technology to allow the two internal 2.5 inch hard drives to be configured as a RAID array. The 680 supports RAID 0, RAID 1 and Intel Matrix RAID which combines the benefits of two RAID volumes in a single RAID array. If you are not currently familiar with RAID arrays Intel has a good white paper on the subject at: http://www.intel.com/design/chipsets/applnots/310855.htm There are a number of benefits to using the RAID feature. Protection is one benefit. When using a RAID 1 array, data is protected by mirroring. The primary RAID volume is duplicated automatically on the second drive, a mirror image of the first. If one of the two hard drives fails the system will still keep working. The bad hard drive can be replaced while the system is running. This is called hot swapping or hot plug. The new drive will automatically be updated to a mirror image of the working drive. Performance is another feature RAID can provide. When configured as a RAID 0 array the two drives in the RAID array are striped. With striping, data is split between two drives. This allows the 680 to read the data more than twice as fast as with a single drive. The performance can be more than twice as fast because the Intel RAID driver also uses the AHCI NCQ function built into the SATA drives. Protection and Performance can be mixed using an Intel Matrix RAID configuration, whereby a RAID 1 and RAID 0 can be setup on the same RAID array. Mission critical data can be stored in the RAID 1 volume and data requiring performance can be stored on the RAID 0 volume. AHCI AHCI stands for Advanced Host Controller Interface and is a feature of the SATA interface that allows for Hot Swapping and Native Command Queuing (NCQ). NCQ allows multiple commands to be sent to the hard drive at one time. The drive decides the best way to order the commands for the best performance from the drive. AHCI is enabled when RAID mode is selected in the BIOS setup. To use AHCI drivers from Intel the BIOS must be set to RAID, not AHCI. The AHCI mode uses the same drivers as used for RAID. Follow the instruction for install the RAID drivers but set the HDD as a Non-RAID Disk in the RAID BIOS setup. J2 680 System Manual Version 1.0 May 11, 2012 58 Enabling RAID in the BIOS The Intel manual for the Intel Matrix Storage Manager covers this same information given below in more detail and can be downloaded from the J2 web site. The documentation below is tailored for the 680 only. Link: http://www.j2retailsystems.com/support/680/RAID/
Perform the following steps to enable the RAID option in the system BIOS:
1. Enter the BIOS Setup program by pressing the DEL key after the BIOS sign-on screen appears. 2. Select the Advanced menu, and then the SATA Configuration menu. 3. Switch the Configure SATA Ports option from SATA to RAID. 4. Press the F10 key to save the BIOS settings and exit the BIOS Setup program. RAID Volume Creation Perform the following steps to create a RAID volume:
1. When the Intel Matrix Storage Manager option ROM status screen appears during POST, press the Ctrl and i keys at the same time to enter the Intel Matrix Storage Manager option ROM user interface. 2. Select Option 1: Create RAID Volume and press the Enter key. 3. Use the up or down arrow keys to select the RAID level and press the Enter key. 4. Unless you have selected RAID 1, use the up or down arrow keys to select the stripe size and press the Enter key. 5. Press the Enter key to select the physical disks. 6. Select the appropriate number of hard drives by using the up or down arrow keys to scroll through the list of hard drives and pressing the Space key to select the drive. When finished, press the Enter key. 7. Select the volume size and press the Enter key. 8. Press the Enter key to create the volume. At the prompt, press the Y key to confirm volume creation. 9. Select Option 4: Exit and press the Enter key. Press the Y key to confirm exit. F6 Installation Method Note: For this step you will need both a USB CD ROM and USB Floppy. Drivers can be downloaded here: http://www.j2retailsystems.com/support/680/RAID/
(continued on next page) J2 680 System Manual Version 1.0 May 11, 2012 59 Perform the following steps to install the Intel Matrix Storage Manager driver during operating system setup:
1. Press the F6 key when prompted in the status line with the Press F6 if you need to install a third party SCSI or RAID driver message. This message appears at the beginning of Windows XP setup (during text-mode phase). Note: Nothing will happen immediately after pressing F6. Setup will temporarily continue loading drivers. You will then be prompted with a screen asking you to load support for mass storage device(s). 2. Press the S key to Specify Additional Device. 3. You will be prompted to Please insert the disk labeled Manufacturer-supplied hardware support disk into Drive A: When prompted, insert the floppy disk containing the following files: IAAHCI.INF, IAAHCI.CAT, IASTOR.INF, IASTOR.CAT, IASTOR.SYS, and TXTSETUP.OEM and press the Enter key. 4. After pressing Enter, you should be presented with a list of available SCSI Adapters. Select your controller from the list. The 680 uses the ICH8R driver. 5. The next screen should confirm your selected controller. Press the Enter key again to continue. 6. At this point, you have successfully F6'd in the Intel Matrix Storage Manager driver and Windows setup should continue. Leave the floppy disk in the floppy drive until the system reboots. Windows setup will need to copy the files from the floppy again to the Windows installation folders. Once Windows setup has copied these files again, you should then remove the floppy diskette so that Windows setup can reboot as needed. 7. During Windows setup, create a partition and file system on the RAID volume as you would on any physical disk. Installing the Intel Matrix Storage Manager Software Once XP is booted you can install the Intel Matrix Storage Manager by just running the iata82_enu.exe install program. install. more information at manual70.pdf. Hot Swapping RAID 1 drives If a RAID 1 drive fails the Matrix Storage Manager will warn the user that a drive has failed. A small Icon appears as shown to indicate a drive has failed. Drive Failed Icon in tray J2 680 System Manual Version 1.0 May 11, 2012 60 If a hot spare is available, all that needs to be done is to swap the bad drive with the hot spare. Be sure to change the correct drive. SATA Ports 0 corresponds to the HDD 0, the top drive in the HDD bay and SATA Ports 1 corresponds to the HDD 1, the bottom drive in the HDD bay. Power to the system does not need to be turned off, and the system will still operate. First remove the bad drive. After removing the bad drive insert the hot spare into the 680. In the Intel Matrix Storage Manager select Advance Mode, and under the Action tab Rescan for Plug and Play Devices screen shot This will cause the drive to be detected by the driver. Drive detected J2 680 System Manual Version 1.0 May 11, 2012 61 The RAID will now rebuild an image of the good drive to the hot spare. Rebuilding Rebuilt The RAID has now mirrored the drive and the system is now protected for a drive failure. Note:
more information on using the 680 RAID function. (Available September 2008) J2 680 System Manual Version 1.0 May 11, 2012 62 In addition to the foam packing inserts, the following contents should be found in the 680 shipping carton. Standard Items 1: System with Power Supply and AC cord 2: Cable Well Cover 3: Printer Power Port Cable
: COM Port Colored Coded Cable Labels J2 680 System Manual Version 1.0 May 11, 2012 63 Overview The 680 can be ordered with a 3 track MSR. This MSR is the same as used on the J2 580/615/625/630 POS systems. The MSR mounts on the right side of the 680 and uses a front facing MSR slot. This allows the 680 unit to be placed side by side, or in tight spaces, and still be able to swipe the card. The MSR appears to the software as a wedge type MSR with all data from the MSR being sent to the keyboard port. The MSR configuration utility can be down loaded from J2 web site. 680 with front swipe MSR J2 680 System Manual Version 1.0 May 11, 2012 64 Installing the 680 MSR The 680 MSR is installed by first removing the two rubber plugs for the option attachment point as shown below. Remove Rubber plugs Then remove the MSR cover plate on the right back side of the unit by removing the two screws, as shown. Remove MSR cover plate J2 680 System Manual Version 1.0 May 11, 2012 65 Connect the cable together as shown add secure the static ground wire with screw provided as shown. Attach cables Attach the MSR using the two screws at the locations shown below. Mounting MSR You may now power up the 680 and the MSR should be working. For a quick test you can open Notepad and swipe a card, the information should appear in Notepad. You can now run the J2 MSR utility if you need any custom settings for the MSR. J2 680 System Manual Version 1.0 May 11, 2012 66 Overview A 2 line by 20 character VFD customer side display is available optional for the J2 680. This customer display is the same as used on the J2 580/615/625/630 POS systems. The J2 680 has the same options as available on the J2 580/615/625/630 POS systems. Secondary display of 10 inch, 12 inch 4:3 and 10.1 inch 16:9 displays are available. J2 680 System Manual Version 1.0 May 11, 2012 67 This option is the same as available on the J2 580/615/625/630 POS systems. This reader uses the Digital Personal module. This option is the same as available on the J2 580/615/625/630 POS systems. Available Q2 2012 Available Q2 2012 This option is the same as available on the J2 580/615/625/630 POS systems. This bracket can be uses when not using a VESA mount. The J2 680 has the same options as available on the J2 580/615/625/630 POS systems. J2 680 System Manual Version 1.0 May 11, 2012 68 Contact Information European Office J2 Retail Systems Ltd. J2 House Clayton Road, Birchwood Warrington WA3 6RP United Kingdom 44 (0) 1925 817003 Phone 44 (0) 1925 811989 Fax USA Office J2 Retail Systems Inc. 9251 Irvine Boulevard Irvine CA 92618 USA Australian Office J2 Retail Systems Pty Ltd Unit 6 83/85 Boundary Road Mortdale NSW 2223 Australia 02 9584 5222 Phone 02 9584 1500 Fax Web site http://www.j2retailsystems.com J2 680 System Manual Version 1.0 May 11, 2012 69 FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This product uses the FCC Data API but is not endorsed or certified by the FCC