submitted | available | document details (if available) | source link |
---|---|---|---|
September 30 2019 | September 30 2019 | Weldon Sanders Microsoft® Word 2019 |
various | Modular Integration Instructions | Users Manual | 186.83 KiB | September 30 2019 |
Wireless/Light Bar Controller Integration Instructions User Manual
(Ref. KDB 996369 D03 OEM Manual v01) FCC ID: DBDWLBC6100; IC: 20318-WLBC6100, HVIN 2350600 2.2 List of applicable FCC rules:
The Wireless/Light Bar Controller Module (Wireless/LBC, WLBC) complies with the following FCC CFR47 Part 15 Subpart C regulations:
15.203 Antenna Requirement 15.204 External radio frequency power amplifiers and antenna modifications. 15.212 Modular Transmitters 15.207 Conducted Limits 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz (digitally modulated) FCC CFR47 Part 15 Subpart AGeneral 15.19 Labeling requirements 15.21 Information to user 2.3 Operational Use Conditions:
The WLBC module has been approved for use in the US, Canada, Australia/New Zealand, and Europe. Changes or modifications to the module could void the users authority to operate the module. The host product operating conditions must be such that there is a minimum separation distance of 20 cm between the antenna and nearby persons. 2.4 Limited Module procedures:
The WLBC has full modular approval. 2.5 Trace antenna designs:
The WLBC does not require Micro-Strip antennas or traces on the host device. All traces and antennas are contained on the WLBC PCB. 2350699 Rev. A 2.6 RF exposure considerations:
The host product operating conditions must be such that there is a minimum separation distance of 20 cm between the antenna radiating structures and nearby persons. The host manufacturer is obligated to confirm the use conditions of the host product to ensure that the distance specified in the instructions is met. In this case the host product is classified as either a mobile device or a fixed device for RF exposure purposes. Maximum EIRP of the module is 8.8 dBm, below the 20 mW low power transmitter output exemption for RF Exposure. The following statement must be included as a CAUTION statement in manuals and OEM products to alert end users of FCC RF Exposure compliance:
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.7 Antennas:
The WLBC uses a non-detachable Printed IFA (Printed Inverted F Antenna) on the module, thus no antenna other than that furnished by the responsible party shall be used with the device. 2.8 Label and compliance information:
Host product manufacturer must provide a physical label stating Contains FCC ID: DBDWLBC6100 and IC: 20318-WLBC6100 in a visible location on the finished product. The module host shall bear the following statement in a conspicuous location on the host and in the manual:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 2350699 Rev. A 2.9 Information on test modes and additional testing requirements:
Host manufacturer should confirm proper operation using a known good module to link to the installed module. Test procedure for the host will require a particular setting to address the good module and proper operational response will be checked. 2.10 Additional testing, Part 15 Subpart B disclaimer:
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules, i.e., 15.207, 15.247) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification, such as Part 15 Subpart B, Unintentional Radiators. Compliance should be checked with all transmitters operating. 2350699 Rev. A
This product uses the FCC Data API but is not endorsed or certified by the FCC