DFX12524G Drone DX 5inch Stunt User Manual

 

SHARPER IMAGE 12+

Rechargeable 2.4GHz DX-2 STUNT DRONE Rechargeable 2.4GHz DX-2 STUNT DRONE Rechargeable 2.4GHz DX-2 STUNT DRONE Rechargeable 2.4GHz DX-2 STUNT DRONE CONTENTS WY Ay +

+H _ +i} +y REMOTE BATTERY INFORMATION 1. Slide open battery compartment 2. Install 6 AA batteries as shown in diagram shown above 3. Replace and close battery compartment AXLITHIUM-POLYMER BATTERY WARNING There is a risk of fire and personal injury if Li-Po battery is punctured, damaged or misused Never expose battery to extreme temperatures INTRODUCTION SPECIFICATIONS Congratulations on your purchase of the Sharper Image Rechargeable 2.4 GHz DX-2 Stunt Drone. Get ready to soar to new heights. Master the art of drone flying and stunting with remote control maneuverability. This lightweight stunting drone will provide hours of fun. Drone Battery: 350 mAh Li-po Remote Controller Battery: 6 x 1.5V AA Charging Time: Approximately 60 minutes Maximum Recommended Altitude 115 ft. READ ALL WARNINGS AND PRECAUTIONS BEFORE USE A\ SAFETY WARNINGS:

. Not recommended for children under 12 years of age. As with all electrical products, precaution should be observed during handling and use to reduce the risk of electrical shock.

+ Adult supervision is required at all times Before each use, an adult should review the product and battery to determine that no damage or hazards exist

+ DO NOT TOUGH SPINNING PROPELLERS

+ Do not allow anything to intentionally make contact in any way with spinning propellers

+ Prevent contact with spinning blades by turning off remote prior to handling drone TABLE OF CONTENTS + Use caution and pay attention to your surroundings while operating drone Do not fly drone into animals, people, or inanimate objects Keep drone away from power lines, buildings, trees, public areas, and any other potentially General Warnings Page 1 Necarcotis.aless Do not operate in rain, heavy wind, and or any type of severe weather Contents and Remote Battery Installation Page 2 Do ist lanid dione on wet eurtacse Charging LiPo and Replacing Propellers Page 3 + Never touch or allow others to touch drone while itis flying

+ Always turn drone off when it is not in use Remote Overview Page 4 Always fly drone in large open areas Operating Drone Page 5 + Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes. Modes and Installing Blade Gaurds Page 6 Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and Tips and FCC Warning Page 7 property rights of others. Pagei Rechargeable 2.4GHz DX-2 STUNT DRONE CHARGING BATTERY Note: The Battery Charger will ight up when it is charging the battery and turn off when the battery is fully charged. Charge time is approximately 60 minutes. Connect the Battery Charger to the Drone insert the USB connector into a USB power source Turn off the drone before charging. Connect the Battery Charger to the Micso USB port on the Drone. Connect USB connector to power source. REPLACING PROPELLERS 1, Follow diagram to the right. 2. Make sure you installed the correct blade. Each blade has a number written on it. Match the

+ The drone shall never be modified or used for anything except its intended purpose. PLEASE RECYCLE OR DISPOSE OF ELECTRONICS PROPERLY RECYCLING INFORMATION IS AVAILABLE AT MSCUSTOMERCARE.COM Page 1 Rechargeable 2.4GHz DX-2 STUNT DRONE Light indicates Throttle Joystick remote is on Forward/

Backwards Adjustment: Slide up to adjust forward and slide down to adjust backwards Increases or decreases drone elevation ON/OFF

< Use L/R arrows for spin Remote Switch Stunt Multi Direction Joystick Auto Orientation 7 5A o+ Side to Side Rechargeable 2.4GHz DX-2 STUNT DRONE OPERATING DRONE Step 1 - Pre Flight Checklist 1. Read all warnings and instructions 2. Install remote batteries, page 2 3. Make sure that drone and remote are powered off 4. Install Blade Guards Drone, page 6. 5. Charge batteries, page 3. Step 2 - Choosing a location

+ Drone is designed to be flown indoors only

+ Always make sure you have enough space to fly drone

+ Always follow warnings, page 1 Step 3 - Starting Drone 1. Making sure your remote is off, slide drone switch to ON. Drone lights will begin to flicker 2. Choose a flat even surface and follow the diagram 3. Turn remote on. Bring the Throttle all the way up then bring it all the way down. Remote will beep and drone lights will flicker rapidly then turn on permanently once paired. 4, Drone is ready for flight. Step 4 - Lift Off 1. Slowly and carefully bring the throttle up. Propellers will begin to spin and drone will begin to elevate. You can compensate for some of the drones drifting by using the Multi Directional Button or by following step 5. You may need to practice this step several times before successfully getting drone into the air. Step 5 - Drone Begins to Drift Follow this step if your drone begins to drift while take off or during flight

+ Drone drifts backwards: Slide the Forward/Backwards Adjustment up

+ Drone drifts forwards: Slide the Forward/Backwards Adjustment down

+ Drone drifts left: Slide the Side to Side Adjustment to the right.

+ Drone drifts right: Slide the Side to Side Adjustment to the left.

+ Drone spins clockwise (viewing drone from top): Slide the Spin Adjustment to the left

+ Drone spins counter-clockwise (viewing drone from top): Slide the Spin Adjustment to the right. Always turn off remote prior to retrieving or picking up drone. This will help you avoid accidently activating propellers. Step 6 - Operating Drone in Flight The drones range is approximately 150 feet

+ Read and be aware of all warnings found on page 1.

* Maintain your desired elevation by using the Throttle

+ Use the Throttle joystick in a circle motion to spin the drone

+ Use the Multi Directional Joystick to move forwards, backwards, and side to side

+ Review step 5 if your drone begins to drift Page 5 Rechargeable 2.4GHz DX-2 STUNT DRONE MODES Auto Landing Button

+ Make sure you have achieved level, balanced flight, where the drone is neither climbing nor descending. This mode allows you to safely and slowly land your drone without having to control the speed. It is done for you automatically. The ideal auto landing height is 25-30 ft. Press the - button to trigger auto land. Remote will beep continuously until drone lands Do NOT touch the left control stick. This will interrupt the landing sequence.

+ To steer the drone during landing, use the right control until drone has reached the ground.

+ Press the - button again to exit auto landing mode. NOTE: Please make sure the throttle joystick is on down position before exit auto landing mode Auto Orientation Button

+ Auto Orientation default setting is off. To enter this mode press Auto Orientation + button. Remote will beep twice.

+ After drone success paired, the 2 white LED lights toward orientation will be the original forward orientation, when drone is in auto orientation mode, whatever the drone spin, the forward orientation will be previous original forward orientation.

+ Remote will beep every 6s to indicate the drone is in Auto Orientation mode.

+ To exit mode, press the +" button. Remote will sound 1 long beep indicating that it has exited Auto Orientation mode. Stunt Button Once you are comfortable flying the drone, use the Stunt Button to perform acrobatic stunts. 1. Hover the drone to at least above 10 feet. 2. Press the Stunt Button. You will hear beeping coming from the remote 3. Move the Multi Directional Button to the desired direction that you would like the drone to flip 4. Once you are comfortable with Stunt Mode, you can create multiple flips. Press the Stunt Button and then move the Multi Directional Button to the desired direction you would like the drone to flip, continue to hold the joystick in the desired direction of the stunt. The drone will INSTALLS SER aeection you held the joystick, for a maximum of 3 stunts in a row.

* Click blade guards in place per diagrams below.

+ Use provided screws and a small screwdriver to secure the blade gaurds before use. ornmisune Bes with the corresponding number on the ON/OFF paaaen

+ Do not subject battery to strong impacts . "1 Always keep battery away from flammable 3. Carefully unscrew the propellers and replace with Aiea =| Slide left to materials the new blade, adjust to the

+ Only use manufacturer specified batter(ies), left and slide

==___ charger(s), and/or adapters, if applicable, NOTE: Blade 1 turns counter clockwise and right to Drone Controller USB Connestor specified by the manufacturer Blade 2 turns clockwise adjust to the Battery is not serviceable right

+ Let battery cool to room temperature before charging While charging, never leave battery unattended

+ Recycle or dispose of battery according to federal, state and local laws KEEP THIS INSTRUCTION MANUAL FOR REFERENCE BATTERY WARNING Banat Spin Adjustment: \

+ nse bates using the correct poly. Do nat short-cret the spt terminal Slide left to spin Replacement *Onty use manactrerspectiod beter), charg) andr aaapes Blade Guards & Propalioes cpkus pedal meneumane ee drone peaees - Rina se, replace, and recharge fappesbe) Balti unde aut spervion colintereibeleNise EP THE PACKAGE FOR REFERENCE AS CONTANS IMPORTANT INFORMATION 5 and slide right to spin drone Page 2 Page 3 enone? Page 4 Rechargeable 2.4GHz DX-2 STUNT DRONE TIPS

+ Do not crash drone into sand or dirt. Drone gears may become clogged

+ When first learning to fiy, practice lifting off and hovering

+ Stay several feet from walls and buildings

+ Always Press Throttle all the way down after crashing or when something gets stuck in propellers

+ Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.

+ Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others.

+ The drone shall never be modified or used for anything except its intended purpose. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment, TROUBLESHOOTING:

When remote switch is tured on, the remote light does not illuminate:

1) Check that batteries in the remote are installed correctly OR 2) Replace with new batteries When the remote is switched on, the remote LED is flashing and remote is beeping:

1) Remote batteries are low; replace them with new batteries Drone and remote property pair, but the drone will not lift-off 1) Drone Li-Po needs charging. Use charging cable to connect the drone to power source. Alter trimming the drone, the drone fight is very unstable and cannot fly properly 1) One or more blades are most likely damaged;

2) Tum off the drone and remote. f 3) Replace with the proper number replacement blade and try flying again. After impact, the drone is unstable:

1) Put the left remote control lever to the left bottom and put the right remote control lever to the right bottom at the same time which connected to the drone (diagram to right). 2) Ifthe above does not resolve the issue, reboot the drone and controller and pair again. Remote Controller and Drone can not be paired:

1) Check Point: Remote Controller must be closed to Drone, not exceed 4 meters. Note: If there are 2 sets of Drones within 4 meters for Pairing, you must pair one successfully before pairing the second set. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two contitions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply wth th Smits for @ Class B gta deuce, pursuant to Part 15 ofthe FOC Rules. These limits are designe to reve reasonable protection against harmful itarforence na reidental installation, Ts equrant gonorates, uses and can radat radi requoncy energy and, ft insted land used in accordance wth the Instructions, may case arma interference to rac cen neatlons. However the is no quarantee It Inecoronce Wl Nt ecurin a particular instalation. If this equipment does cause harmful interference to rado or television reception, which canbe determined by tuning the equipment off and onthe users encouraged to ty to correct ne inerlerence by one oF more ofthe folowing measures:

Reorint or relate the receiving antenna, Increase the separation between the equipment and recive Connect the equipment ito an outet ona circu ferent om that to whic the roelers connected, Consult the dealer or an experienced rado/TV techncan for help. Sharper Image. All Rights Reserved. SHARPER IMAGE name and logo are registered trademarks manufactured and marketed by MerchSource, LLC under license. All other logos and trademarks are proprietary to their respective ovners. The artwork and design of this package are protected by US copyright law and may not be reproduced, distributed, displaced, published or used for any purpose without prior written permission. Altering, removing or reproducing any of the trademark or copyright notices on this package is not permitted.

(2016 MerchSource, LLC. All rights reserved. Distributed by MerchSource, LLC, Irvine, CA 92618, PATENT PENDING Printed in China Page 7