submitted | available | document details (if available) | source link |
---|---|---|---|
August 28 2019 | August 28 2019 | 福昕PDF打印机 版本 8.3.0.0331 |
various | User-Manual | Users Manual | 1.35 MiB | August 28 2019 |
and The installation height of this product is 15 meters and the service area is 3km. UHF Antenna specification Technical parameters Frequency range (MHz) 410470 Bandwidth (MHz) 20 Polarization mode Vertical Gain (dBi) Input impedance () 4 50 Voltage standing wave ratio 2.0 Maximum power (W) Joint type Antenna length (mm) Antenna weight (g) Extreme wind speed (km/h) 20 TNC 293 50 90 Remark: Antenna structure for elastic whip, and resistance to bending. UHF Antenna Specification Technical Parameters Technical indicators QT900L Frequency range (MHz) 902.4928 Bandwidth(MHz) 26 Polarization mode Vertical Gain (dBi) Input impedance ( ) 3 50 Voltage standing wave ratio 1.5 Maximum power(W) Joint type Antenna length(cm) Antenna weight (g) 20 R-SMA 19.6 40 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 60cm between the radiator & your body. IC WARNING Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS
(RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interfrences.
(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil. Cet quipement est conforme aux limites d'exposition au rayonnement ISED tablies pour un environnement non contr?l. Cet quipement doit tre install et utilis une distance minimale de 60 cm entre le radiateur et votre corps. single 2.2 List of applicable FCC rules This module meets the requirements of Part 15 Subpart C Section 15.247, FCC CFR Title 47 Part 90, FCC CFR Title 47 Part 2. 2.4 Limited module procedures This module is an module. 2.6 RF exposure considerations Integration is strictly limited to fixed categorized end-products where a separation distance of at least 60 cm between the radiating part and any human body can be assured during normal operating conditions. 2.7 Antennas This module only allows connection one of the two antennas in the instruction manual. If other antennas are used, re-evaluation is required. 2.9 Information on test modes and additional testing requirements5 This module is test stand-alone, if more another modules work together with this module, please evaluation the multiple RF exposure. 2.10 Additional testing, Part 15 Subpart B disclaimer The final end product must be labeled in a visible area with the following Contains TX FCC ID:
2ABNA-TRM121 .If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
Integration is strictly limited to mobile/fixed categorized end-products where a separation distance of at least 60 cm between the radiating part and any human body can be assured during normal operating conditions. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter).then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. IMPORTANT NOTE:
This module is intended for OEM integrator only and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following Contains TX FCC ID:
2ABNA-TRM121 .If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
Integration is strictly limited to mobile/fixed categorized end-products where a separation distance of at least 60 cm between the radiating part and any human body can be assured during normal operating conditions. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter).then the IC authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. IMPORTANT NOTE:
This module is intended for OEM integrator only and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following Contains TX IC:
11648A-TRM121 .If the size of the end product is smaller than 8x10cm, then additional IC statement is required to be available in the users manual:
Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS
(RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interfrences.
(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil. Cet quipement est conforme aux limites d'exposition au rayonnement ISED tablies pour un environnement non contr?l. Cet quipement doit tre install et utilis une distance minimale de 60 cm entre le radiateur et votre corps.
This product uses the FCC Data API but is not endorsed or certified by the FCC