AEG4 DashCam Users Manual

Dashboard Camera User Manual UD13287B-B User Manual 2018 Hangzhou Hikvision Digital Technology Co., Ltd. About this Manual This manual applies to Dashboard Camera. This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (Hikvision) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Trademarks and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission. Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. i Regulatory Information FCC Information FCC compliance: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Please take attention that changes or modification not expressly approved by for compliance could void the users authority to operate the equipment. This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. EU Conformity Statement responsible the party This product and - if applicable - the supplied accessories too are marked with

"CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2014/35/EU, the EMC Directive 2014/30/EU, RE Directive 2014/53/EU. ii 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info. Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Refer to technical specifications for detailed information. Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with AC 24V or DC 12V according to the IEC60950-1 standard. Refer to technical specifications for detailed information. Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. Make sure that the plug is firmly connected to the power socket. iii When the product is mounted on wall or ceiling, the device shall be firmly fixed. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the camera by yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, replace the lens cap to protect the sensor from dirt. Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise

(which is not a malfunction), and affect the endurance of sensor at the same time. The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. Do not place the camera in extremely hot, cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. To avoid heat accumulation, good ventilation is required for operating environment. Keep the camera away from liquid while in use. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Indicates a hazard with a high level of iv risk, which if not avoided, will result in death or serious injury. ii 1 Introduction 1.1 Product Features Dashboard camera records the traffic status via access of multiple cameras. Dashboard camera adopts integrated structure and design. It features with high resolution, wide field angle and easy installation, etc., which makes it suitable for variety traffic status. The main features are as follows:

Supports the access of 4-ch of TVI cameras Supports two-way audio Built-in Wi-Fi module, supports Wi-Fi AP Supports 4G network Supports preview, playback and editing parameters via APP Supports connecting to iVMS-5200 for uploading and playback Supports license recognition, face detection, driver behavior analysis etc. Easy installation and operation Low power consumption and high performance The smart analysis function subjects the device. 1.2 Overview 1.2.1 Camera The overview of the camera is shown below. Overview You can also turn on/off Wi-Fi AP by pressing Wi-Fi AP indicator. You can reboot the device by pressing RESET for 3s. 1 USB InterfaceRecording Indicator4G IndicatorWi-Fi AP IndicatorLensMounting ScrewSIMRESETTF1TF2 Indicator Status Description REC Indicator Solid Unlit Solid 4G Indicator Flashing Recording is normal. Recording exception. Check the TF card. 4G signal is normal;

platform has connected. 4G signal is normal;

platform unconnected. Wi-Fi AP Indicator Unlit No signal. Solid->

Fast Flashing Flashing

->

Flashing Slow Wi-Fi AP is on. You can connect other device to Wi-Fi AP. Wi-Fi AP is off. Press it to turn on. 1.2.2 Cable The devices cables are shown in below. Cable Description 4 PIN TVI Interfaceconnect 4 PIN TVI camera 4 PIN DBA Interfaceconnect 4 PIN DBA camera 8 PIN Expansion Interfaceconnects expansion cable, involving:

1. Power Cable: connect ACC with vehicles ACC, VCC with vehicle batterys positive pole, GND with vehicle batterys negative pole. 2. Alarm Interface: connect 4 PIN alarm button. Press alarm button to send alarm to the platform when in emergency. OBD Port: Connect serial port line for debugging. The camera connected should be compatible to the device. The power supply of the dashboard camera subjects to the specification. 2 8 PIN Expansion Interface4 PIN DBA Interface4 PIN TVI InterfacePower CableAlarm InterfaceOBD PortExpansion Cable 2 Installation Before you start:

Please make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Check whether the power supply is matched with your power output to avoid damage. Be sure that there is enough space to install the camera and accessories. Make sure the part, which is used to install the camera, is strong enough to withstand four times the weight of the camera and the mounting. If the product does not function properly, please contact your dealer or the nearest service center. Do not disassemble the camera for repair or maintenance by yourself. Do not pull and drag the camera cables hard. 2.1 Install TF Card and SIM Card You can install TF card and SIM card according to needs. TF card will be overwritten when its full. The former recording will be covered automatically. Please backup recording when accident occurred. SIM card is used to connect 3G/4G network. The installation of SIM card and TF card is same. Steps:

1. Remove the screw, open the card cover. Open Card Cover 2. Push the TF card (self-provided) into the slot until you hear a click. 3. Cover back the card cover, and tighten the screw. 3 Remove the screw. 2.2 Install Dashboard Camera Steps:

1. Clean the mounting surface with a mixture of isopropyl and water. Clean Mounting Surface 2. Remove the stand from the device. 3. Peal the paster off the stand. Remove the Stand Peal the Paster 4. Paste the stand to the mounting surface with stand notch vertically downward. 5. Push the dashboard camera to the stand along the notch direction, until the camera stuck to the notch. 6. Adjust the lens to the target angle. 7. Remove the camera from the stand. Tighten the set screw of the lens. Attach the camera to the stand again. Installation finished. Fix the Lens 4 Remove the stand.PasterStand Notch Set Screw of the Lens 2.3 Wiring and Start Device Steps:

(Optional) Connect TVI camera to the dashboard 1. cameras TVI interface according to needs. 2. Connect the dashboard cameras power cable to the vehicles battery:

a. Connect ACC with vehicles ACC;

b. Connect VCC with vehicle batterys positive pole c. Connect GND with vehicle batterys negative pole. 3. The dashboard camera starts automatically once the vehicle started. Check the recording indicator. If recording indicator is bright and steady, the camera is started normally. Dashboard camera starts recording automatically after powered on. Contact the dealer to obtain the APP to manage the device. 3 Trouble Shooting Trouble Solution Starting dashcam failed. Recording failed. Recorded videos are fuzzy. Ensure the automobiles battery met the needs of the camera. Ensure the power cable is connected normally. Ensure the automobile started normally and the power supply is normal. Ensure TF card is installed.

(8G, Class 10 or above) Check TF card status, e.g., its format and lifespan. If it is not well, replace it with a good one. Tear off the proof film on lens. Clean the lens and glass. 5