K1102EK Card Reader User Manual

 

DS-K1100 Series Card Reader User Manual DS-K1100 Series Card Reader User Manual 2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be Hikvision). This user manual

(hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. This Manual is applicable to card reader. Series DS-K1101 Series DS-K1102 Series DS-K1103 Series DS-K1104 Series Models DS-K1101M DS-K1101MK DS-K1101C DS-K1101CK DS-K1102M DS-K1102MK DS-K1102C DS-K1102CK DS-K1102E DS-K1102 EK DS-K1102 EM DS-K1102 EMK DS-K1103M DS-K1103MK DS-K1103C DS-K1103CK DS-K1104M DS-K1104MK DS-K1104C DS-K1104CK Description Card Reader Card Reader Card Reader Card Reader About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (Hikvision) reserves all i DS-K1100 Series Card Reader rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Trademarks and other Hikvisions trademarks and ITS HARDWARE, SOFTWARE AND FIRMWARE, logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH IS PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INTERNET SECURITY RISKS;

HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. INSPECTION, OR OTHER ii DS-K1100 Series Card Reader Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation iii DS-K1100 Series Card Reader EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info. Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. iv DS-K1100 Series Card Reader Use only power supplies listed in the user instructions:

Model Manufacturer Standard TS-A018-120015Ec Shenzhen Transin CEE Technologies Co., Ltd Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions:

Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Follow Warnings safeguards serious injury or death. these prevent to Cautions Follow these precautions to prevent potential injury or material damage. Warnings All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. v DS-K1100 Series Card Reader If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself.

(We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Cautions Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The appropriate temperature is -20 to 65. The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Preventive and Cautionary Tips vi DS-K1100 Series Card Reader To guarantee the card reader works properly, please read and obey the notes below. If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100m, you are advised to power the card reader by external 12V (range: -%10 ~ +%10) DC power supply, which is nonswitched and linear. To guarantee the communication between the controller and the card reader, you must use RVVP cable above 0.5 to connect them. If the card reader is installed outside or in environment easy to permeable, it is advisable to install a waterproof shield. If you need to install several card readers, the distance among them must over 30cm. To reduce the noise in long distance transmission, the shield of cable should connect to the GND of both controller and card reader terminal. Please take care of your card and report card loss in time when card is lost. If you require a higher security level, use multiple authentication modes. Multiple card types are supported. Please select an appropriate card type according to the card performance and the usage scenarios. vii DS-K1100 Series Card Reader Content Chapter 2 Chapter 1 1.1 1.2 1.3 Introduction ........................................................ 1 Front View ..................................................................... 1 Rear View ...................................................................... 3 Slide View ...................................................................... 5 Installation .......................................................... 7 Installing PSAM Card ..................................................... 7 2.1 Introduction for DIP Switch ........................................... 7 2.2 2.3 Definition of Cable ......................................................... 8 2.4 Wiring Cables ................................................................ 9 2.5 Installing Card Reader .................................................. 11 Sound Prompt and Indicator .............................. 13 Chapter 3 viii DS-K1100 Series Card Reader Chapter 1 Introduction DS-K1100 series card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via either RS-485 protocol or Wiegand protocol. And a build-in tamper-proof module helps to protect card reader from malicious damage. As to the physical appearance, the PC+ABS material makes water proof and dust proof possible in poor environment. 1.1 Front View The front view of DS-K1101 series card reader is shown below:

Figure 1-1 DS-K1101MK/DS-K1101CK Figure 1-2 DS-K1101M/DS-K1101C 1 DS-K1100 Series Card Reader The front view of DS-K1102 series card reader is shown below:

Figure 1-3 DS-K1102MK/DS-K1102CK Figure 1-4 DS-K1102M/DS-K1102C The front view of DS-K1103 series card reader is shown below:

Figure 1-5 DS-K1103MK/DS-K1103CK Figure 1-6 DS-K1103M/DS-K1103C 2 DS-K1100 Series Card Reader The front view of DS-K1104 series card reader is shown below:

Figure 1-7 DS-K1104MK/DS-K1104CK Figure 1-8 DS-K1104M/DS-K1104C 1.2 Rear View The rear view of card reader is shown below:

Figure 1-9 Rear View of DS-K1101 Series 3 12345 DS-K1100 Series Card Reader Figure 1-10 Rear View of DS-K1102 Series Figure 1-11 Rear View of DS-K1103 Series 4 13453514 DS-K1100 Series Card Reader Figure 1-12 Rear View of DS-K1104 Series Table 1-1 Description of Rear View Cable Interface of RS-485, Power, LED Control, etc. Name Buzzer Tamper-proof Module DIP Switch PSAM Card Slot (available for CPU card reader) No. 1 2 3 4 5 1.3 Slide View The side view of card reader is shown below:

5 4531 DS-K1100 Series Card Reader Figure 1-13 DS-K1101 Series Figure 1-14 DS-K1102 Series Figure 1-15 DS-K1103 Series Figure 1-16 DS-K1104 Series 6 DS-K1100 Series Card Reader Chapter 2 Installation 2.1 Installing PSAM Card PSAM card slot is only available for CPU card reader. Insert the PSAM card into the slot according to the direction shown below. Figure 2-1 PSAM Card Slot 2.2 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch from left to right is 1 ~ 8. Figure 2-2 DIP Switch Module Table 2-1 Description of DIP Switch Icon Description Represent 1 in binary mode Represent 0 in binary mode For example, binary value of the following status is: 0000 1100. 7 DS-K1100 Series Card Reader Figure 2-3 DIP Switch Module Table 2-2 Description of DIP Switch No. Description DIP Switch Status 1 ~ 4 Address of RS-485 1: 1 0: 0 5 6 7 8 Read card No. or file in card.

(Only available for CPU card reader.) Wiegand protocol or RS-485 protocol. Wiegand Protocol

(available when No. 6 is 1) Matched Resistance

(available for RS-485 protocol) 1: read card No;

0: read file in card. 1: Wiegand protocol;

0: RS-485 protocol. 1: Wiegand protocol of 26-bit;

0: Wiegand protocol of 34-bit. 1: Enable;

0: Disable. 2.3 Definition of Cable The description of 10 cables is shown below. Table 2-3 Description of Cable Description RS-485+

Blue LED Control (available for Wiegand Protocol) RS-485-

Color Yellow Brown Blue 8 DS-K1100 Series Card Reader Description Color Beep Control (available for Wiegand Protocol) Purple Gray Case Sensor (available for Wiegand Protocol) Green Wiegand W0 (available for Wiegand Protocol) White Wiegand W1 (available for Wiegand Protocol) Black Orange GND Red LED Control (available for Wiegand Protocol) Red PWR (DC +12V) 2.4 Wiring Cables Purpose:

Wire the cables between controller and card reader, thus to establish the communication between them. Steps for RS-485 communication mode:

1. 2. Set the DIP switch of No. 6 as 0. Set the DIP switch of No. 1 ~ 5 for RS-485 address and reading card mode. For details, please refer to 2.2 Introduction for DIP Switch. 3. Wire the cable between controller and card reader as shown below. 9 DS-K1100 Series Card Reader Figure 2-4 Wiring for RS-485 Communication Mode Steps for Wiegand communication mode:

1. Set the DIP switch of No. 6 as 1. 2. Set the DIP switch of No. 5 and 7 for reading card mode and to 2.2 Wiegand protocol. For details, please Introduction for DIP Switch. refer 3. Wiring the cable between controller and card reader as shown below. 10 YellowBlueBlackRedBlackRedGreenWhitePurpleOrangeBrownControllerCard Reader DS-K1100 Series Card Reader Figure 2-5 Wiring for Wiegand Communication Mode 2.5 Installing Card Reader Before you start:

Set the DIP switch. For details, refer to 2.2 Introduction for DIP Switch. Steps:

11 YellowBlueBlackRedBlackRedGreenWhitePurpleOrangeBrownControllerCard Reader DS-K1100 Series Card Reader Fix the gang box on the wall or other place. Connect the cables between controller and card reader. For details, refer to 2.4 Wiring Cables. Push the card reader to match the fixed gang box. Fasten the screw to keep the components together. Fix the side cover onto the card reader, press the cover to make it tightly fit the reader. 1. 2. 3. 4. 5. 12 DS-K1100 Series Card Reader Chapter 3 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn blue and blink for 1 time. Then it will turn red and blink for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. During using the card reader, it will send out different sounds prompt and the LED indicator on it have different statuses. You can refer to tables below for detailed information. Table 3-1 Description of Prompt Sound Sound Prompt Description RS-485 protocol: Pressing keys prompt;

Swiping card prompt; Time out prompt for pressing keys or swiping card. Wiegand protocol: Pressing keys prompt;

Swiping card prompt. The operation of pressing keys or swiping card is valid. The operation of pressing keys or swiping card is invalid. Alarm of tamper-proof. The card reader is unencrypted. One beep Two rapid beeps Three slow beeps Rapidly continuous beeps Slowly continuous beeps Table 3-2 Description of LED Indicator Description LED Indicator Status Green and blinking Solid green Card reader is working normally. The operation of pressing keys or swiping 13 DS-K1100 Series Card Reader LED Indicator Status Description Solid red Red and blinking Red and Keeping rapidly blinking card is valid. The operation of pressing keys or swiping card is invalid. For RS-485 protocol: Registering failed or card reader is offline. Failed to get key files of PSAM card; Failed to detect the PSAM card. Available for reading file mode of CPU card: PSAM is not inserted or undetected. 020000001090312 14 DS-K1100 Series Card Reader UD05659B-C 15