S400BT Bluetooth headset Owner Manual Users Manual

 

S400BT Bluetooth stereo headset Users manual Welcome to use this Bluetooth stereo headset, S400BT. Please read this users manual carefully before use. Brief introduction 1. Bluetooth wireless communication technology Bluetooth is a standard of close range wireless communication technology that was drawn up by Ericsson, IBM, Intel, Nokia and Toshiba. With Bluetooth technology, we can achieve the highest transmission rate among cell phones, computers, printers, PDAs and other devices. The max transmission range of class II is 10 meters while the max transmission ranges of class I can reach up to 100 meters. 2. About S400BT S400BT is a Bluetooth V3.0 stereo headset. It supports the following Bluetooth profiles:

HSP Headset Profile HFP Hands-free Profile A2DP Advanced Audio Distribution Profile AVRCPAudio/Video Remote Control Profile You can enjoy music wirelessly by using S400BT. It has the following features:

1) Pairing with a Bluetooth cell phone or PDA supporting HFP profile. Answer a call, end a call and reject a call Redial last number Voice dial Adjust the volume Call transfer between the headset and your Bluetooth cell phone Microphone mute 2) Pairing with a Bluetooth cell phone or Bluetooth transmitter supporting A2DP profile. Enjoy music wirelessly Adjust the volume Remote control pause/play Remote control previous/next track 1 3) Easy to switch between the call and music, you will not miss the incoming call during listening to music. 4) Every time the headset is turned on, it will connect to last connected device automatically. Note: In order to complete above function, the Bluetooth profiles of paired device must be same as the headset. And even though the paired device and the headset support the same Bluetooth profiles, functions may vary due to specification differences of the paired devices. Before use 1. Overview 1 2 3 4 5 6 7 8 LED indicator Bluetooth paring button Charging/aux-in port Power button 1 2 3 4 5 6 7 8 2 Built-in microphone Multi-functions Touch panel

(Volume down/up, next/previous song, pause /play) Right speaker Left speaker 2. Charging for headset The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low power, the headset emits five Dong tones every 5 minutes and the red LED flashes instead of blue LED. Please recharge the battery of the headset. The way of charging as following:

Using USB cable 1. Plug the special charging clip into the charging jack of headset, make it clip the headset as pictures shown :

2. Plug another side of cable to the USB port of PC Red light on: Charging Red light off: Finish charging 3. It will takes about 2 hours to finish charging Remarks:

1) The battery is recyclable. 2) Batteries (battery pack or batteries installed) shall not be exposed to Getting started 1. Turning on/off the headset excessive heat place, such as sunshine, fire or the like. Functions Turning on Turning off Operation Single press power button to turn on the unit, p Press power button and hold to turn off the unit LED indicator White on one second Red LED on one second Remark: In order to save power, the headset will turn off automatically if no devices can be connected after 5 minutes. 2. Pairing the headset with Bluetooth devices 1) How to enter pairing mode Functions Entering pairing mode Operation When in BT Active mode, single press to enter the BT paring mode, press and hold for 2 seconds to exit paring mode. LED indicator Red and White LED flash alternately Remark: Pairing mode will last 2 minutes. If no devices can be connected after 2 minutes, it will return to standby mode automatically. 2) Pairing headset with Bluetooth cell phone Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled cell phone. The pairing procedures are subject to different models of cell phones. Please refer to your cell phone users manual for further information. The general pairing procedures are as follows:

1) Keep your headset and phone within 1 meter when pairing;

2) Make the headset enter pairing mode (please refer to How to enter pairing mode);

3) Activate your cell phones Bluetooth function and set your cell phone to search for Bluetooth devices within range, and select S400BT from the list of devices shown;

4) According to the indication, enter password or PIN No: 0000. ( If the mobile phone supports Bluetooth V3.0, password is not required.). If prompted by your cell phone to connect, select Yes (this will vary among cell phone models);

5) After successful paired, choose and connect S400BT from the list of devices shown on cell phone;

6) After successful connecting, blue LED of headset will flashes twice every 4 seconds Remarks:

If pairing is failed, please turn off the headset first and then re-pair according to steps 16 mentioned above. After pairing is successful, the headset and the cell phone will remember each other, they will no need to re-pair next time. The headset can remember 8 paired devices, when the number of paired devices exceeds 8, the first one will be replaced. Every time the headset is turned on, it will connect to last connected device automatically. If you want to pair it with other devices, please turn off the Bluetooth function of last connected devices first and pair the headset with the new device according to steps 16 mentioned above. 3 Note:

Not all the mobile phones support all the functions listed above. Please refer to your mobile phone users manual. tone. Different function and prompt tone according to different mobile phone. When the volume is adjusted to max or min, you will hear one prompt When pressing the answer button on some mobile phones, the call will be transferred to the mobile phone. You can switch the call to the headset by using the conversation switch button or through operating on the mobile phone. Please refer to your mobile phone user manual for further information. 4. Playing music When the headset connects to a mobile phone or Bluetooth transmitter which supports A2DP, you can enjoy music wirelessly through the headset. Gesture Tab Quick Swipe Up Quick Swipe Down Slow Swipe Up Slow Swipe Down Swipe Forward Swipe Backward Functions and behavior Play/Pause a track playing or answer/end the call. (Only valid in BT Active mode.) Increase volume level by 1 step. Decrease the volume level by 1 step. Increase volume level continuously. Decrease the volume level continuously. Change to next track. (Only valid in BT Active mode.) Change to previous track. (Only valid in BT Active mode.) Notes:

When playing music on some mobile phones, the music will be transmitted to the mobile phones speaker instead of the headset. You tone. have to select transmit the sound via Bluetooth in the settings menu and then choose S400BT as speaker device. The music will be transmitted to the headset. Please refer to your mobile phones users manual for further information. When the volume is adjusted to max or min., you will hear one prompt If you want to remote control last/next song, pause/play, it needs your Bluetooth mobile phone or Bluetooth transmitter paired with the headset to support AVRCP profile, please refer to the users manual of your mobile phone or Bluetooth transmitter for further information. Care and maintenance Read the following recommendations carefully before using S400BT. Following these you will be able to enjoy this product for many years. Keep it dry and dont put it in the dump place to avoid the products internal circuit being affected. Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic parts. Dont expose the product to cold areas. It may damage the internal circuit Dont try to disassemble the product as it may get damaged if you are not board. professional. Dont let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged. Dont use intensive chemical products or detergent to clean the product. Dont scratch the surface with sharp things. Dont use this product during strenuous exercise. It may damage the product if the sweat into product. In case the product doest function properly, send it to the store you bought it. The staff will help you to solve the problem Specifications Bluetooth version Bluetooth profiles Operating distance Headset music time Headset talk time Headset standby time Bluetooth V3.0 Headset, Hands free, A2DP, AVRCP 10meters About 4 hours About 4.5 hours Approx 150 hours Charging input Headset charging time Battery capacity 500mA DC5.0V About 2 hours 610mAH Notes:

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. IMPORTANT INFORMATION US AND CANADA FCC AND IC STATEMENT:

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS 210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;

and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC/IC RADIATION EXPOSURE STATEMENT This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. DCLARATION DE LA FCC ET DIC Cet appareil est conforme la partie 15 des rgles de la FCC, ainsi qu la norme RSS 210 exempte de licence dIndustrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) Cet appareil ne doit pas provoquer dinterfrences nuisibles; et (2) cet appareil doit accepter toutes les interfrences reues, y compris celles susceptibles dentraner un dysfonctionnement de lappareil. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. DCLARATION DE LA FCC ET DIC SUR LEXPOSITION AUX RADIATIONS Cet appareil est conforme la norme RSS 102 de la FCC/IC relative aux limites dexposition aux radiations dans un environnement non contrl Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FOR EU COUNTRIES WEEE NOTICE The Directive on Waste Electrical and Electronic Equipment (WEEE), which entered into force as European law on 13th February 2003, resulted in a major change in the treatment of electrical equipment at end-of-life. addition, to promote the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. The WEEE logo on the product or on its box indicating collection for electrical and electronic equipment consists of the crossed-out wheeled bin, as shown below. This product must not be disposed of or dumped with your other household waste. You are liable to dispose of all your electronic or electrical waste equipment by waste. Isolated collection and proper recovery of your electronic and electrical waste equipment at the time of disposal will allow us to help conserving natural resources. Moreover, proper recycling of the electronic and electrical waste equipment will ensure safety of human health and environment. For more information about electronic and electrical waste equipment disposal, recovery, and collection points, please contact your local city center, household waste disposal service, shop from where you purchased the equipment, or manufacturer of the equipment. ROHS COMPLIANCE This product is in compliance with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. EU BATTERIES DIRECTIVE 2006/66/EC A new battery directive 2006/66/EC on Battery and Accumulator replacing directive entered into force on the 26th September 2008. The directive applies to all types of batteries and accumulators (AA, AAA, button cells, lead acid, rechargeable packs) including those incorporated into appliances except for military, medical and power tool applications. The directive sets out rules for collection, treatment, recycling and disposal of batteries, and aims to prohibit certain hazardous substances and to improve environmental performance of batteries and all operators in the supply chain. INSTRUCTIONS FOR USERS ON REMOVAL, RECYCLING AND DISPOSAL OF USED BATTERIES To remove the batteries from your equipment or remote control, reverse the procedure described in the owners manual for inserting batteries. For products with a built-in battery that lasts for the lifetime of the product, removal may not be possible for the user. In this case, recycling or recovery centers handle the dismantling of the product and the removal of the battery. If, for any reason, it becomes necessary to replace such a battery, this procedure must be performed by authorized service centers. In the European Union and other locations, it is illegal to dispose of any battery with household trash. All batteries must be disposed of in an environmentally sound environmentally sound collection, recycling and disposal of used batteries. WARNING: Danger of explosion if battery is incorrectly replaced. To reduce risk of The symbol indicating separate collection for all batteries and accumulators shall be the crossed-out wheeled bin shown below:

DECLARATION OF CONFORMITY HARMAN International hereby declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/

EC, ErP 2009/125/EC Directive and RoHS 2011/65/EU Directive The declaration of conformity may be consulted in the support section of our Web site, accessible from www.jbl.com. AVIS CONCERNANT LES DEEE La directive relative aux dchets dquipements lectriques et lectroniques

(DEEE), adopte comme loi europenne le 13 fvrier 2003, a suppos un important Lobjectif principal de cette directive est de prvenir les DEEE et de favoriser la rduire la mise au rebut. Le logo des DEEE appos sur cet quipement ou sur son emballage, qui indique la collecte des quipements lectriques et lectroniques, est reprsent sous la forme dune poubelle barre, comme indiqu ci-dessous. Ce produit ne doit pas tre jet avec les ordures mnagres. Il vous incombe de vous rendant un point de collecte appropri en vue de les recycler. Une collecte isole et une rcupration approprie de vos dchets dquipements lectriques ou lectroniques au moment de la mise au rebut nous permettent de contribuer la prservation des ressources naturelles. Par ailleurs, un recyclage appropri des dchets dquipements lectriques ou lectroniques assure la protection de la sant humaine et de lenvironnement. Pour obtenir de plus amples informations sur la mise au rebut, la rcupration et les points de collecte des dchets dquipements lectriques ou lectroniques, contactez votre mairie, votre service de collecte des dchets, le magasin qui vous a vendu lquipement, ou le fabricant du produit. CONFORMIT LA DIRECTIVE RELATIVE LUTILISATION DE CERTAINES SUBSTANCES DANGEREUSES Cet appareil est conforme la directive 2011/65/UE du Parlement europen et du Conseil du 8 juin 2011 relative la limitation de lutilisation de certaines substances dangereuses dans les quipements lectriques et lectroniques. DIRECTIVE 2006/66/CE RELATIVE AUX PILES ET ACCUMULATEURS La nouvelle directive 2006/66/CE relative aux piles et accumulateurs est entre en vigueur le 26 septembre 2008. Cette directive sapplique tous les types de piles et accumulateurs (AA, AAA, pile bouton, pile/accumulateur plomb-acide, pile/

accumulateur rechargeable), notamment ceux incorpors dans les appareils sagit doutils lectriques. Cette directive tablit des rgles pour la collecte, le traitement, le recyclage et la mise au rebut des piles et accumulateurs; elle vise par ailleurs interdire certaines substances dangereuses et amliorer les performances environnementales des piles et accumulateurs et de tous les oprateurs de la chane dapprovisionnement. INSTRUCTIONS DE RETRAIT, DE MISE AU REBUT ET DE RECYCLAGE DES PILES ET ACCUMULATEURS USAGS Pour retirer les piles de votre quipement ou de la tlcommande, inversez la procdure dinsertion des piles dcrite dans le mode demploi. Cette procdure est impossible sur les quipements munis dune batterie intgre dont la dure de vie correspond celle du produit. Dans ce cas, les centres de recyclage ou de rcupration sont chargs du dmantlement du produit et du retrait de la batterie. Si, pour quelque raison que ce soit, vous devez remplacer ce type de batterie, adressez-vous un centre de services autoris. Dans lUnion europenne et dans dautres rgions, il est illgal de jeter les piles ou accumulateurs usags avec les ordures mnagres. Les piles et accumulateurs doivent tre mis au rebut dans le respect de lenvironnement. Contactez lentreprise charge de la gestion des dchets pour obtenir de plus amples informations sur la collecte, le recyclage et la mise au rebut cologiques des piles et accumulateurs usags. AVERTISSEMENT: danger dexplosion si la pile nest pas correctement remplace. Pour rduire les risques de brlure ou dincendie, veillez ne pas dmonter, craser, percer ou court-circuiter la pile, lexposer une temprature suprieure 60C

(140F), ou la jeter au feu ou dans leau. Lorsque vous remplacez les piles, utilisez Le symbole de la poubelle barre, illustr ci-dessous, indique la collecte spare de lensemble des piles et accumulateurs:

DCLARATION DE CONFORMIT HARMAN International dclare que cet quipement est conforme aux exigences essentielles et autres dispositions pertinentes de la directive 1999/5/CE concernant les quipements hertziens et les quipements terminaux de tlcommunications, dcoconception applicables aux produits lis lnergie, et la directive 2011/65/

UE relative la limitation de lutilisation de certaines substances dangereuses dans les quipements lectriques et lectroniques. Vous pouvez consulter la dclaration de conformit la section Support de notre site Web, ladresse www.jbl.com.