RC339A Remote control User Manual

User guide for Remote Control RC3394003/01BR The remote control has been programmed to control your set-top box and can be programmed to control your TV. Installing Batteries The remote requires 2xAAA batteries. A diagram inside the battery compartment of the remote indicates proper placement of the batteries. When batteries are properly installed, the light on the remote blinks each time a key is pressed Know your Remote The diagram below describes each key on your remote control. Functions may vary between different services. Refer to the user guide for your set-top box for descriptions of specific functions. Product Introduction 1) This RCU is transmitting IR and RF. There is a simple set up feature for TV/Home Theatre device. 2) The RCU can be set-up to control a RF or an IR STB (mutually exclusive). 3) The RF platform is BLE, using HOGP as the top layer. Before the RCU can control the STB, the RCU must pair with the STB first. 4) The IR protocol to control the STB is NEC. When RCU is not connected to any STB via BLE, MCU use IR to control STB. 5) When BLE is not connected, all the STB IR keys are transmitted through NEC IR protocol. Custom ID is 0x1620. Set STB Control Medium 1) Set to IR Mode:

Press <<MENU + 1>> simultaneously for 3 seconds. 2) Set to RF Mode:

Press <<MENU + 2>> simultaneously for 3 seconds;

3) Set dual-function Keys as TV Keys Press << OK + 3>> simultaneously for 3 seconds;

4). Set Volume Keys as TV Keys:

Press <<MENU + 3>> simultaneously for 3 seconds. 5). Set dual-function Keys as STB Keys:

Press <<MENU + 4>> simultaneously for 3 seconds. Voice Function 1) Press and released <Google Assistant> key to open the voice function, RCU will close the voice function after receiving the stop command sent by the host. 2)When RCU is recording, the STB-LED is always on. OTA The RCU software supports upgrade via OTA (Over-The-Air). From diagram above, the STB can transfer the RCU firmware by the BLE link. The OTA process can be triggered by the user using the RCU or by the STB itself. The RCU OTA IMAGE need to be downloaded into the STB itself. After the OTA is completed, the RCU will have a new firmware. Simple Setup 1) Simple Setup is a feature helps user to automatically set up the remote control via STB. After being set by Simple Setup, the RCU will be able to control TV/AMP. 2) Below IR function could be configured to control TV through simple setup:

TV Power, TV input, TV Mute, TV Vol+ and TV vol-. 3) After a successful simple setup for TV, RCU will automatically set dual -function keys into TV mode Battery Voltage Monitor LVD check will be triggered after a signal key is released in user mode. 1.When the LVD is detected (battery voltage<2.3V);

2. While RCU works in BLE mode, it supports Bluetooth standard service of battery level notification. The paired host is then able to get battery level of the RCU. Sleeping Mode When no any activity need to do, the RC enters sleeping for power saving purpose. The sleeping mode behaves as below:

1) All LEDs are off. 2) IR and RF communications are stopped. 3) Any key press will wake up the RC. FCC ID:2AGOFRC339A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful i nterference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante.