Aruba AP120 and AP121 Access Point Users Manual

 

Aruba AP-120 Series Indoor Access Point Installation Guide About the Aruba AP-120 Series Access Points The Aruba AP-120 series of wireless access points support the imminent IEEE 802.11n (currently draft 2.0) standard for high-performance WLAN. These access points use MIMO (Multiple-in, Multiple-out) technology and other high-throughput mode techniques to deliver high-performance, pre-802.11n 2.4GHz and 5GHz functionality while simultaneously supporting existing 802.11a/b/g wireless services. The AP-120 series access points are available in versions with single or dual radios and with integrated antennas or RP-SMA interfaces that support detachable antennas. The AP-120 series access points work only in conjunction with an Aruba Mobility Controller. The Aruba AP-120 series access points provide the following capabilities:

Wireless transceiver

Protocol-independent networking functionality

IEEE 802.11a/b/g or 802.11n operation as a wireless access point

IEEE 802.11a/b/g or 802.11n operation as a wireless air monitor

Compatibility with IEEE 802.3af PoE as well as high power over Ethernet pre-standards

(PoE + / 802.3at)

Central management configuration, and upgrades through an Aruba Mobility Controller Figure 1 AP-120 Series Access Points AP-120/124 ap12_001 AP-121/125

(3 x RP-SMA interfaces for detachable antennas)

(3 x integrated dual-band antennas) Package Contents

AP-120 series access point

Installation guide (this document) N O T E Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. 0510457-02 | December 2007 1 N O T E Additional mounting kits for use with the AP-120 series access points are sold separately. Contact your Aruba sales representative for details. Before You Begin WLAN Planning Determine how many Aruba APs are needed for your wireless network deployment and where they will be installed. You can easily accomplish this planning using Arubas automated RF Plan site-survey software (available separately). This process is considered WLAN or RF planning and should have been completed during the master Aruba Mobility Controller installation and configuration. In typical Aruba installations, the mobility controllers are configured and installed before the APs. For WLAN planning assistance, refer to the Indoor Access Points: Site Survey and Planning Pre-

Deployment Guide and the RF Plan Installation and User Guide. Pre-Installation Network Requirements After WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba Mobility Controller(s) must be installed and initial setup performed before the Aruba Access Points are deployed. For initial setup of the Mobility Controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller. Pre-Installation Checklist Before installing your AP-120 series access point, be sure that you have the following:

For the AP-120/AP-124: External antennas as specified in the network deployment plan

CAT5 UTP cable of required length

One of the following power sources:

IEEE 802.3af-compliant Power over Ethernet (PoE) source

Supports full functionality for AP-120/AP-121; supports reduced functionality for AP-124/AP-125

IEEE Power Over Ethernet + (PoE+) source output at 56Volts @ 350mA

The POE source can be any power source equipment (PSE) controller or midspan PSE device

Aruba AP AC-DC adapter kit (sold separately)

Aruba Mobility Controller provisioned on the network:

Layer 2/3 network connectivity to your access point

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an A record

DHCP Server with vendor-specific options Summary of the Setup Process N O T E It is important that you verify the items listed under Pre-Installation Checklist before you attempt to set up and install an AP-120 series AP. 2 Aruba AP-120 Series Indoor Access Point |

Installation Guide Successful setup of an AP-120 series access point consists of four tasks, which must be performed in this order:

1. Verify pre-installation connectivity. 2. Identify the specific installation location for each AP. Install each AP. 3. 4. Verify post-installation connectivity. 5. Configure each AP. N O T E

CAUTION Aruba Networks, in compliance with governmental requirements, has designed the AP-120 series access points so that only authorized network administrators can change the settings. For more information about AP configuration, refer to the ArubaOS Quick Start Guide and Aruba OS User Guide. Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used. Verifying Pre-Installation Connectivity Before you install APs in a network environment, make sure that the APs will be able to locate and connect to the Mobility Controller when powered on. Specifically, you must verify the following conditions:

When connected to the network, each AP is assigned a valid IP address

APs are able to locate the Mobility Controller (Mobility Controller Discovery) Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the Mobility Controller. Identifying Specific Installation Locations

CAUTION RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches

(35 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. You can mount the AP-120 series access point on a wall or on the ceiling. Use the AP placement map generated by Arubas RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in RF plan. Aruba AP-120 Series Indoor Access Point |

Installation Guide 3 Unidentified Known RF Absorbers/Reflectors/Interference Sources Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed location. RF absorbers include:

Cement/concrete: Old concrete has high levels of water dissipation, which dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration within the concrete, blocking RF signals.

Natural Items: Fish tanks, water fountains, ponds, and trees

Brick RF reflectors include:

Metal Objects: Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets

Do not place an AP between two air conditioning/heating ducts. Make sure that APs are placed below ducts to avoid RF disturbances. RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Lunch rooms and call centers with cordless headsets Installing the AP N O T E N O T E Service to all Aruba Networks products should be performed by trained service personnel only. Using the Integrated Wall-Mounting Slots The keyhole-shaped slots on the back of the AP can be used to attach the device upright to an indoor wall or shelf. When you choose the mounting location, allow additional space at the right of the unit for cables. For product dimensions, see Product Specifications in this guide. Allow 2 inches (5 cm) of additional space at the right side of the installed unit for cables, and make sure enough space is available for antenna articulation. 1. At the mounting location, install two screw on the wall or shelf, 1 7/8 inches (4.7 cm) apart. If you are attaching the device to drywall, Aruba recommends using appropriate wall anchors (not included). 2. Align the mounting slots on the rear of the AP over the screws and slide the unit into place (see Figure 2). 4 Aruba AP-120 Series Indoor Access Point |

Installation Guide Figure 2 Installing the AP-120 series Access Point on a Wall 3. On the AP-121 or AP-125, orient the antennas. For best performance, swivel the antennas so that they are oriented vertically, preferably in the same plane, parallel to the wall (see Figure 3). Figure 3 Antenna Orientation on a Wall-Mounted AP-121/AP-125 On the AP-120 or AP-124, install the external antennas according to the manufacturers instructions, and connect the antennas to the antenna interfaces on the AP (see Figure 4). Figure 4 Antenna Interfaces on the AP-120/AP-124 ap Using the Integrated Ceiling Tile Rail Slots The snap-in tile rail slots on the rear of the AP can be used to securely attach the device directly to a 15/

16 wide, standard ceiling tile rail.

CAUTION Make sure the AP fits securely on the ceiling tile rail when hanging the device from the ceiling, because poor installation could cause it to fall onto people or equipment. Aruba AP-120 Series Indoor Access Point |

Installation Guide 5 1. Pull the necessary cables through a prepared hole in the ceiling tile near where the AP will be placed. If necessary, connect the console cable to the console port on the back of the AP. 2. 3. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30-

degree angle to the ceiling tile rail (see Figure 5). Make sure that any cable slack is above the ceiling tile. Figure 5 Orienting the Ceiling Tile Rail Mounting Slots 4. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks into place on the ceiling tile rail. 5. On the AP-121 or AP-125, orient the antennas. For best results, rotate the antennas so that they are vertical (perpendicular to the body of the AP) (see Figure 6). Figure 6 Antenna Orientation on a Ceiling-Mounted AP-121/AP-125 ap1 On the AP-120 or AP-124, install the external antennas according to the manufacturers instructions, and connect the antennas to the antenna interfaces on the AP (see Figure 4). Connecting Required Cables Install cables in accordance with all applicable local and national regulations and practices. 6 Aruba AP-120 Series Indoor Access Point |

Installation Guide N O T E N O T E Ethernet Ports The RJ45 Ethernet ports (ENET0 and ENET1) support 100/1000Base-T auto-sensing MDI/MDX connections. Use these ports to connect the AP to a twisted pair Ethernet LAN segment or directly to an Aruba Mobility Controller. Use a 4- or 8-conductor, Category 5 UTP cable up to 100 m (325 feet) long. Aruba 12x APs are intended only for installation in Environment A as defined in IEEE 802.3.af, Power over Ethernet. All interconnected equipment must be contained within the same building, including the interconnected equipments associated LAN connections. When installed in an air-handling space, such as above suspended ceiling (plenum), the unit is required to be powered through PoE only. Additional cabling such as Fast Ethernet (FE) cables installed in such spaces should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP. The 100/1000 Mbps Ethernet ports are on the bottom of the AP. These ports have RJ-45 female connectors with the pin-outs shown in Table 1. Table 1 Connector for Ethernet Ports ENET0 and ENET1 Connector Pin Signal Name GE Connection FE Connection PoE 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 BI_DA+ Bi-directional pair A+ RX+

BI_DA Bi-directional pair A RX BI_DB+ Bi-directional pair B+ TX+

BI_DC+ Bi-directional pair C+ Spare pair BI_DC Bi-directional pair C Spare pair BI_DB Bi-directional pair B TX BI_DD+ Bi-directional pair D+ Spare pair BI_DB Bi-directional pair D Spare pair POE negative POE negative POE positive POE positive POE positive POE positive POE negative POE negative Serial Console Port The serial console port allows you to connect the AP to a serial terminal or a laptop for direct local management. This port is an RJ-45 female connector with the pinouts described in Table 2. Connect this port in one of the following ways:

Connect it directly to a terminal or terminal server using an Ethernet cable.

Use a modular adapter to convert the RJ-45 (female) connector on the AP to a DB-9 (male) connector, and connect the adapter to a laptop using an RS-232 cable. See Figure 7 for connector details of the adapter. Table 2 Connector for Serial Console Port Connector Pin Signal Name Function 1 2 3 4 5 6 7 8 TXD GND GND RXD 3 4 5 6 Pins not listed are not connected. Transmit Ground Ground Receive Aruba AP-120 Series Indoor Access Point |

Installation Guide 7 Figure 7 RJ-45 (Female) to DB-9 (Male) Modular Adapter Conversion RJ-45 Female Pin-Out TxD GND RxD 1 2 3 4 5 6 7 8 Direction Input Output Internal Connections RJ-45 3 4 5 6 TxD GND RxD DB-9 2 5 3 DB-9 Male Pin-Out Ground RxD TxD 9 8 7 6 5 4 3 2 1 Direction Input Output Power Connection The AP-120 series AP has a single 5V DC power jack socket to support powering through an AC-to-DC mains electric power adapter. Connecting a Security Cable To provide added security for the AP, you can attach a security cable to the back of the unit (see Figure 8). Figure 8 Security Lock Connection Verifying Post-Installation Connectivity The integrated LEDs on the AP can be used at this point to verify that the AP is receiving power and initializing successfully (see Table 3). Refer to the ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity. Table 3 AP-120 Series LED Meanings LED PWR ENET 0

(100/1000 Mbps) ENET 1

(100/1000 Mbps) Color/State Meaning Green Steady Green flashing Green/Amber off Green on Amber on Green/amber blinking Green/Amber off Green on Amber on Green/amber blinking Power on, device ready System initializing No link 1000 Mbps link 10/100 Mbps link Data activity No Link 1000 Mbps link 10/100 Mbps link Data activity 8 Aruba AP-120 Series Indoor Access Point |

Installation Guide Table 3 AP-120 Series LED Meanings LED 11A/N 11B/G/N Color/State Meaning Amber on Green on Amber Green Wireless link is legacy 11a. Wireless link is 11n 5Ghz band. Wireless link is legacy 11b or 11g. Wireless link is 11n 2.4Ghz band. Configuring the AP-12x AP Provisioning/Reprovisioning Provisioning parameters are unique to each AP. These local AP parameters are initially configured on the Mobility Controller which are then pushed out to the AP and stored on the AP itself. Aruba recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details. AP Configuration Configuration parameters are network or controller specific and are configured and stored on the Mobility Controller. Network configuration settings are pushed out to the AP(s) but remain stored on the Mobility Controller. Configuration settings can be configured via the ArubaOS Web UI, ArubaOS CLI, or Aruba MMS. Refer to their respective guides for further details: the ArubaOS User Guide or Aruba Mobility Management System User Guide. Product Specifications Mechanical

Dimensions (antenna stowed) (HxWxD):

4.9 inches x 5. 13 inches x 2 inches

12.4 cm x 13 cm x 5.1 cm

Weight: 15 oz/0.42 kg

Shipping Dimensions:

9.5 inches x 7.25 inches x 4.5 inches

24.1 cm x 18.4 cm x 11.4 cm

Temperature:

Operating: 0C to 50C (32F to 122F)

Storage: 10C to 70C (14F to 158F)

Relative Humidity: 5% to 95% non-condensing

Altitude: 8,000 ft @ 28C (82.4F)

Mounting: Wall, ceiling, or desktop mountable

Antennas:

3 integrated articulating dual-band antenna elements (AP-121, AP-125)

3 RP-SMA interfaces for external antennas (AP-120, AP-124)

Visual Status Indicators (LEDs): See Table 3 Aruba AP-120 Series Indoor Access Point |

Installation Guide 9 Electrical

Ethernet:

2 x 100/1000 Base-T auto-sensing Ethernet RJ-45 Interfaces

MDI/MDX

IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)

Power over Ethernet (IEEE 802.3af compliant), 48V DC/200mA (see Table 1 for pin configuration)

Power:

5 VDC power interface, supports powering through an AC-to-DC mains electric power adapter

POE support on Ethernet ports:

802.3af-compliant POE sourcing devices POE+ (56 V @ 350 mA) Wireless LAN

Network Standards: IEEE 802.11b, IEEE 802.11g, IEEE 802.11a, and IEEE 802.11n

Antenna Type:

Integrated 802.11a/b/g/n omni-directional high-gain antenna

Detachable 802.11a/b/g/n omni-directional high-gain antenna

Antenna Gain (Integrated Antennas):

2.4 2.5 GHz/3.2 dBi (max)

5.180 5.825 GHz/5.2 dBi (max)

Radio Technology:

Orthogonal Frequency Division Multiplexing (OFDM)

Direct Sequence Spread Spectrum (DSSS)

Radio Modulation Type:

802.11b - CCK, BPSK, QPSK

802.11g - CCK, BPSK, QPSK,16-QAM, 64-QAM

802.11a - BPSK, QPSK,16-QAM, 64-QAM

802.11n draft 2.0

Media Access Control: CSMA/CA with ACK

Supported Frequency Bands 2.4GHz:

2.400 ~ 2.4835GHz (Global), channels country specific

Supported Frequency Bands 5GHz:

5.150 ~ 5.250GHz (low band), country-specific

5.250 ~ 5.350GHz (mid band), country-specific

5.470 ~ 5.725GHz (Europe), country-specific

5.725 ~ 5.825GHz GHz (high band), country-specific

Data Rates:

802.11b - 1, 2, 5.5, 11 Mbps per channel

802.11g - 6, 9, 12, 18, 24, 36, 48 and 54 Mbps per channel

802.11a - 6, 9, 12, 18, 24, 36, 48 and 54 Mbps per channel

802.11n - Data rate MCS0 MCS15 (from 6.5 Mbps to 300 Mbps) 10 Aruba AP-120 Series Indoor Access Point |

Installation Guide Safety and Regulatory Compliance Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location:

www.arubanetworks.com/pdf/0510272-01.pdf

CAUTION RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches

(35 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Proper Disposal of Aruba Equipment For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com. Waste of Electrical and Electronic Equipment Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). European Union RoHS Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2002/95/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the RoHS label shown at the left indicating conformance to this Directive. Aruba AP-120 Series Indoor Access Point |

Installation Guide 11 China RoHS Aruba products also comply with China environmental declaration requirements and are labeled with the EFUP 50 label shown at the left.

Hazardous Materials Declaration

Mercury

(Hg)

Cadmium

(Cd)

Hazardous Substances)

Chromium VI Compounds

(Cr6+) Polybrominated Biphenyls

(PBB)

Polybrominated Diphenyl Ether

(PBDE) O O O O O O O O O O

Lead

(Pb) X X

(Parts)

PCA Board

Mechanical Subassembly O: SJ/T11363-2006 This component does not contain this hazardous substance above the maximum concentration values in homogeneous materials specified in the SJ/T11363-2006 Industry Standard. X: SJ/T11363-2006 This component does contain this hazardous substance above the maximum concentration values in homogeneous materials specified in the SJ/T11363-2006 Industry Standard.

This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product.

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. 2007 Aruba Networks, Inc. All rights reserved. www.arubanetworks.com 1322 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax 408.227.4550 12 Aruba AP-120 Series Indoor Access Point |

Installation Guide