RAP3WN Remote Access point User Manual

 

Aruba RAP-3 Remote Access Point Installation Guide The Aruba RAP-3WN and RAP-3WNP are single-radio, single-band wireless access points (AP) that support the IEEE 802.11n standard for high-performance WLAN. These access points use MIMO (Multiple-in, Multiple-out) technology and other high-throughput mode techniques to deliver high-performance, 802.11n 2.4 GHz functionality while simultaneously supporting existing 802.11 b/g wireless services. The RAP-3 ships with Aruba Instant software. Therefore, out of the box, the RAP-3 will operate as a Virtual Controller (VC) or an Instant AP. However, the RAP-3 can be converted to operate as a Remote AP (RAP). For information about the IAP to RAP conversion, see RAP Conversion. The RAP-3 requires Aruba Instant 3.0 to operate as a Instant AP and ArubaOS 6.1.4.0 to operate as a Remote AP. Wireless transceiver Protocol-independent networking functionality IEEE 802.11b/g/n operation as a wireless access point IEEE 802.11b/g/n operation as a wireless air monitor Compatibility with IEEE 802.3af PoE Package Contents 1x RAP-3WN or RAP-3WNP Access Point 1x Installation Guide (this document) 1x Aruba Instant Quick Start Guide 1x RJ-45 Ethernet Cable 1x 12V Power Adapter (RAP-3WN only) 1x 48V Power Adapter (RAP-3WNP only) Figure 2 Fast Ethernet Port Pin Out DC IN (Power Socket) The RAP-3 power adapter (included) connects to the DC IN port. The RAP-3 does not have an On/Off switch. The device turns on when the power adapter is attached and plugged into a power outlet. The device turns off when you disconnect the power adapter from the power source (outlet). LED PSE Color(s) Activity Action Green Off On Not sourcing PoE power Sourcing PoE power to an 802.3af Powered Device Flashing PoE power sourcing error Reset Button The RAP-3 is equipped with reset button, that when pushed, resets the device to factory default settings. The reset button is located on the bottom of the device and is recessed in a small, round hole. To reset the RAP-3, insert a small, narrow object, such as a pin or paperclip, into the hole and press and hold the button while powering on the RAP-3. This will return the device to factory default settings. The RAP-3WN ships with a 12V power supply and the RAP-3WNP ships with a 48V power supply. These power supplies are not interchangeable. RAP-3 Installation Top View Figure 3 Top View Tabletop Mounting The RAP-3 is shipped with a stand to use on flat (i.e. table top) surfaces. Place the RAP-3 in the stand (see Figure 5) and place the stand on a flat, level surface. Figure 5 Stand Installation 3 0 _ 3 2

-

P A I RAP Conversion If your network administrator has instructed you to convert the RAP-3 to work in RAP mode, follow the process below to complete the RAP conversion. 1. Power up the RAP-3. 2. Connect to Instant SSID. 3. Login to the RAP-3 by navigating to http://instant.arubanetworks.com and login to the Instant WebUI. The default username is admin and the default password is admin. See the included Aruba Instant Quick Start Guide for more information. 4. Navigate to the Maintenance tab in the top right. 5. Click on the Convert tab. 6. Select Remote APs managed by a Mobility Controller from the drop down menu. 7. Enter the IP address of the controller. This is provided by your network administrator. 8. Click Convert Now to complete the conversion (see Figure 6). 9. The RAP-3 will reboot and begin operating in RAP mode. Figure 6 IAP-RAP Conversion over the Internet The 48V power adapter that ships with the RAP-3WNP does not come with a country specific power cord. This cord must be ordered separately. Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use them to repack the product in case there is a need to return it. USB Port The RAP-3 is equipped with a USB port to support cellular modems. Figure 4 Bottom View (RAP-3WNP Shown) Before You Begin Before installing your RAP-3 Remote Access Point, please ensure you have the following:

RAP-3 (included) 1 x RJ-45 Ethernet Cable (included) 1 x Power Adapter (included) RAP-3 Overview Figure 1 Rear View (RAP-3WN Shown) Pwr E0 E1 E2 WLAN PSE 2 0 _ 3 2

-

P A I E0 (WAN port) E1 (LAN port) E2 (LAN port) LEDs The RAP-3WN has five LED indicators that display the status of the device. The RAP-3WNP has an additional LED called PSE. PWR: When lit, the RAP-3 is powered on E0:Indicates activity and/or status on this port. E1: Indicates activity and/or status on this port E2: Indicates activity and/or status on this port WLAN: Indicates wireless status and activity PSE (RAP-3WNP only): Indicated the PSE status on the RAP-3WNP 1 0 _ 3 2

-

P A I LED PWR Color(s) Activity Action Green 10/100Base-T Ethernet Ports The RAP-3 has three 10/100Base-T (RJ-45) Ethernet ports for wired network connectivity. E0: WAN port (top) E1: LAN port (middle) E2: LAN port (bottom) On the RAP-3WNP, port E2 has PoE power sourcing capability (PSE) to supply power to any compliant 802.3af powered device (class 0-4). WLAN Green Ports (E0, E1, E2) Green On Off Off On Power on No power Wireless is inactive Wireless is active Flashing Radio mode Off On No link Link established Flashing Ethernet activity 4 0 _ 3 2

-

P A I Connecting the Required Cables The RAP-3 must be connected to a network device that has access to the Internet, such as a router or modem. To complete the installation of the RAP-3:

1. Connect one end of the provided RJ-45 cable to port E0 on the RAP-3. 2. Connect the other end of the RJ-45 cable to a free RJ-45 port on your modem or router. 3. Attach the provided power adapter to the DC IN port on the RAP-3. 4. Connect the other end of the power adapter to a power outlet. The RAP-3 is now powered on. To verify this, ensure that the PWR LED is solid green. Verifying Successful Installation Once the RAP-3s PWR LED has come up, the device will take 2 to 3 minutes to complete the boot cycle. Once the boot cycle is complete, you can connect to your company or corporate network. Product Specifications Electrical Ethernet:

3 x 10/100Base-T auto-sensing Ethernet RJ-45 Interfaces MDI/MDX IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). Power - RAP-3WNP:

48VDC power interface, supports powering through an AC-to-DC power adapter Power -RAP-3WN:

12 VDC power interface, supports powering through an AC-to-DC power adapter If a power adapter other than the one provided by Aruba Networks is used in the US or Canada, it should be NRTL Listed, with appropriate voltage and current rating, marked LPS or Class 2, and suitable for plugging into a standard power receptacle in the US and Canada. For additional specifications on this product, please refer to the data sheet. The data sheet can be found at www.arubanetworks.com. Proper Disposal of Aruba Equipment For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com. Waste of Electrical and Electronic Equipment Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). European Union RoHS Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2002/95/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the RoHS label shown at the left indicating conformance to this Directive. China RoHS 10 Aruba products also comply with China environmental declaration requirements and are labeled with the EFUP 10 label shown at the left.

Hazardous Materials Declaration

(Hazardous Substance)

(Parts)

(PCA Boards)

(Mechanical Sub-Assemblies)

SJ/T11363-2006

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.

This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product.

!

CAUTION RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. EMC Compliance and Warning Statement FCC Class B Part 15 This device complies with Part 15 of the Federal Communications Commission

(FCC) Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.

!

CAUTION Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. The device has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091 for an uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instructions, may cause interference harmful to radio communications. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada. Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. L utilisation de ce dispositif est autorise seulement aux conditions suivantes :

(1) il ne doit pas produire de brouillage et (2) l utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Le prsent appareil est conforme aux normes CNR dindustrie Canada applicables aux appareils radio exempts licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit produire de brouillage, et 2. Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. EU Regulatory Conformance This product is CE marked according to the provisions of the R &

TTE Directive (99/5/EC) - CE(!). Aruba Networks Inc., hereby declares that this RAP-3 device models are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. CE(!) The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the following location in the EU community.

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. Safety and Regulatory Compliance Aruba Networks provides a multi-language document that contains country-

specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum

!

CAUTION Aruba access points must be installed by a professional installer. The professional installer is responsible for ensuring that grounding is available and it meets applicable local and national electrical codes. Aruba RAP-3 Remote Access Point Installation Guide Contacting Aruba Networks Web Site Support Main Site Support Site http://www.arubanetworks.com https://support.arubanetworks.com Software Licensing Site https://licensing.arubanetworks.com/login.php Wireless Security Incident Response Team (WSIRT) http://www.arubanetworks.com/support/wsirt.php Americas and APAC Support Email support@arubanetworks.com EMEA Support Email emea.support@arubanetworks.com WSIRT Email Please email details of any security problem found in an Aruba product. wsirt@arubanetworks.com Telephone Support Aruba Corporate FAX

+1 (408) 227-4500

+1 (408) 227-4550 Support United States Universal Free Phone Service Number (UIFN): Australia, Canada, China, France, Germany, Hong Kong, Ireland, Israel, Japan, Korea, Singapore, South Africa, Taiwan, and the UK All Other Countries 800-WI-FI-LAN (800-943-4526)

+800-4WIFI-LAN (+800-49434-526)

+1 (408) 754-1200 Copyright 2010 Aruba Networks, Inc. AirWave, Aruba Networks, Aruba Mobility Management System, Bluescanner, For Wireless That Works, Mobile Edge Architecture, People Move. Networks Must Follow., RFprotect, The All Wireless Workplace Is Now Open For Business, and The Mobile Edge Company are trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners. Open Source Code Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source Legal Notice The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors. Warranty This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information, refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS. Altering this device (such as painting it) voids the warranty. www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax 408.227.4550 Aruba RAP-3 Remote Access Point | Installation Guide Part Number 0511012-04 | March 2012