| submitted | available | document details (if available) | source link |
|---|---|---|---|
| Microsoft Word - User Manual for T77H332 eden Acrobat Distiller 8.1.0 (Windows) |
| various | User Manual | Users Manual | 295.66 KiB |
COMPANY CONFIDENTIAL T77H332 User Manual NFC (Near Field Communication) Module T77H332 00 00 Project Name Rev. FOXCONN Part No. Module Rev. Revision History Revision Date Originator 0.0 2012/12/20 Wei.Liao Comment Initial 1 COMPANY CONFIDENTIAL Content REVISION HISTORY ....................................................................................................................................................... 1 1. INTRODUCTION .......................................................................................................................................................... 3 2. WIFI ALLIANCE CONFORMANCE .......................................................................................................................... 6 3. HARDWARE SPECIFICATION ................................................................................................................................. 7 4. PRODUCT REQUIREMENTS .................................................................................................................................. 11 2 COMPANY CONFIDENTIAL 1. Introduction The T77H332.XX IEEE802.11b/g/n module is based on Marvell 88W8782UB0-NAP2C000 solution that is provide the combined functions of DSSS and OFDM baseband modulation, MAC, CPU, OTP (one time programmable) memory, host interfaces, power management unit (PMU) and direct conversion WLAN RF radio. 1.1 Scope The wireless LAN is compliant to IEEE 802.11b and IEEE 802.11g and IEEE 802.11n standard. The data rate of 802.11b is up to 11Mbps and fallback rates of 5.5, 2, 1Mbps. The data rate of 802.11g is up to 54Mbps and fallback rates of 48,36,24,18,12,9, 6Mbps. The data rate of 802.11n HT20 with 800ns GI is up to 65Mbps and fallback rates of 58.5, 52, 39, 26, 19.5, 13, 6.5Mbps; the data rate of 802.11n HT20 with 400ns GI is up to 72.2Mbps and fallback rates of 65, 57.8, 43.3, 28.9, 21.7, 14.4, 7.2Mbps. The data rate of 802.11n HT40 with 800ns GI is up to 135Mbps and fallback rates of 121.5, 108, 81, 54, 40.5, 27, 13.5Mbps. The data rate of 802.11n HT40 with 400ns GI is up to 150Mbps and fallback rates of 135, 120, 90, 60, 45, 30, 15Mbps. 1.2 Function IEEE802.11b/g/n (1X1) based on Marvell 88W8782U solution. USB 2.0 Interface, High and Full Speeds supported. Powered by the host with a 3.3V +/- 10% supply. Two PCB printed antennas. One SPDT switch for antenna diversity. RoHS and Green Compliant. Linux supported with drivers based on Fedora Core 8. 3 1.3 Electrical Characteristics Parameter Frequency Range Current Consumption Input Supply Voltage Absolute maximum voltage Tx Output Power 11b 11g 11n-HT20 11n-HT40 Storage Temperature Storage Humidity Operation Temperature HBM MM ESD Level COMPANY CONFIDENTIAL Minimum 2.4
-
Typical
~
-
Maximum 2.5 600 Units GHz mA 2.97 3.3 3.63 16.5 12.5 11.5 10.5
-20 0 0
-
-
18 14 13 12
~
~
~
1.5K 200 19.5 15.5 14.5 13.5 85 90 60
-
-
V dBm dBm dBm dBm
%
V V Remark: The TX output powers just depend on conduct band-edge limit. 4 1.4 USB 2.0 Characteristics COMPANY CONFIDENTIAL Parameter Minimum Typical Maximum Units Low / Full Speed Input high voltage (driven) Input high voltage (floating) Input levels Input low voltage Differential input sensitivity Differential common mode range Output low voltage Output high voltage (driven) Output SE1 voltage Output signal crossover voltage Output level Driver characteristics Rise time Fall time Clock timing Full speed data rate 2.0 2.7
-
0.2 0.8
-
2.8 0.8 1.3 4 4
-
-
-
-
-
-
-
-
-
-
-
-
12.0
-
3.6 0.8
-
2.5 0.3 3.6 2.0 20 20
-
V V V V V V V V V ns ns Mb/s Parameter Minimum Typical Maximum Units High Speed 100 525
-50
-10.0 360
-10.0 700
-900 500 500
-
-
-
-
-
-
-
-
-
-
-
480 150 625 500 10.0 440 10.0 1100
-500
-
-
-
mV mV mV mV mV mV mV mV ps ps Mb/s Input levels Output level High-speed squelch detection threshold
(differential signal amplitude) High-speed disconnect detection threshold
(differential signal amplitude) High-speed data signaling common mode voltage range High-speed idle level High-speed data signaling high High-speed data signaling low Chirp J level (differential voltage) Chirp k level (differential voltage) Driver characteristics Clock timing Rise time (10% - 90%) Fall time (10% - 90%) Full speed data rate 5 COMPANY CONFIDENTIAL 2. WIFI ALLIANCE CONFORMANCE The Module is certified by the Wi-Fi Alliance. The Module and standard PC driver passes the Wi-Fi System Interoperability Test Plan including the following:
A. IEEE 802.11-2007 Standard for LAN/MAN Specific requirements Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications B. IEEE P802.11n-2009 Standard for Information Technology Telecommunications and information exchange between systems - Local and metropolitan area networks Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications Amendment 5:
Enhancements for Higher Throughput C. Supported Encryption WEP64- and 128-bit encryption with hardware TKIP processing (WPA) AES-CCMP hardware implementation as part of 802.11i security standard (WPA2) AES-Cipher-Based Message Authentication Code (CMAC) as part of the 802.11w security standard WLAN Authentication and Privacy Infrastructure (WAPI) 6 COMPANY CONFIDENTIAL 3. Hardware Specification 3.1 IEEE802.11b Mode Radio Technology Operating Frequency Modulation Schemes Channel Numbers Data Rate Media Access Protocol
(MAC) Transmitter Output Power 18.0 dBm+/-1.5dBm for all data rate. Frequency Accuracy Minimum Receiver Sensitivity Level Direct Sequence Spread Spectrum (DSSS) 2412 ~ 2484MHz ISM band DQPSK, DBPSK and CCK 11 channels for United States 13 channels for Europe Countries 14 channels for Japan 1Mbps, 2Mbps, 5.5Mbps and 11Mbps CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance)
+/-15ppm Typical 99dBm for 1Mbps @ 8% PER Typical 96dBm for 2Mbps @ 8% PER Typical 92dBm for 5.5Mbps @ 8% PER Typical 89dBm for 11Mbps @ 8% PER Typical 4% for 1Mbps @18dBm output power Typical 4% for 2Mbps @18dBm output power Typical 4% for 5.5Mbps @18dBm output power Typical 4% for 11Mbps @18dBm output power EVM (peak) IEEE802.11g Mode 3.2 Radio Technology Operating Frequency Modulation Schemes Channel Numbers Orthogonal Frequency Division Multiplexing
(OFDM) 2412 ~ 2472MHz ISM band BPSK, QPSK, 16QAM, 64QAM 11 channels for United States 13 channels for Europe Countries 6 Mbps, 9, 12, 18, 24, 36, 48, and 54Mbps CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) Data Rate Media Access Protocol
(MAC) Transmitter Output Power 14.0 dBm+/-1.5dBm for all data rate. Frequency Accuracy Minimum Receiver
+/-15ppm Typical 91dBm for 6Mbps @ 10% PER 7 IEEE802.11n (HT20) Mode Sensitivity Level EVM 3.3 Radio Technology Operating Frequency Modulation Schemes Channel Numbers Data Rate COMPANY CONFIDENTIAL Typical 87dBm for 18Mbps @ 10% PER Typical 75dBm for 54Mbps @ 10% PER Typical 31dB for 6Mbps @15dBm output power Typical 31dB for 54Mbps @15dBm output power Orthogonal Frequency Division Multiplexing
(OFDM) 2412 ~ 2472MHz ISM band BPSK, QPSK, 16QAM, 64QAM 11 channels for United States 13 channels for Europe Countries 800ns GI: 6.5Mbps, 13, 19.5, 26, 39, 52, 58.5 and 65Mbps 400ns GI: 7.2Mbps, 14.4, 21.7, 28.9, 43.3, 57.8, 65.0 and 72.2Mbps CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) Media Access Protocol
(MAC) Transmitter Output Power 13.0 dBm+/-1.5dBm for all data rate Frequency Accuracy Minimum Receiver Sensitivity Level EVM
+/-15ppm Typical 91dBm for 6.5Mbps @ 10% PER Typical 83dBm for 26Mbps @ 10% PER Typical 72dBm for 65Mbps @ 10% PER Typical 32dB for MCS0 @15dBm output power Typical 32dB for MCS7 @15dBm output power 3.4 IEEE802.11n (HT40) Mode Radio Technology Operating Frequency Modulation Schemes Channel Numbers Data Rate Orthogonal Frequency Division Multiplexing
(OFDM) 2422 ~ 2462MHz ISM band BPSK, QPSK, 16QAM, 64QAM 9 channels for all countries 800ns GI: 13.5 Mbps, 27, 40.5, 54, 81, 108, 121.5 and 135Mbps 400ns GI: 15Mbps, 30, 45, 60, 90, 120, 135 and 150Mbps Media Access Protocol
(MAC) Transmitter Output Power 12.0 dBm+/-1.5dBm for all data rate CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) 8 Frequency Accuracy Minimum Receiver Sensitivity Level EVM
(Test condition:
Enable full packet channel estimate) COMPANY CONFIDENTIAL
+/-15ppm Typical 88dBm for 13.5Mbps @ 10% PER Typical 79dBm for 54Mbps @ 10% PER Typical 69dBm for 135Mbps @ 10% PER Typical 31dB for MCS0 @15dBm output power Typical 31dB for MCS7 @15dBm output power Remark: The minimum sensitivity level is measured in FOXCONN RD Lab in shielding room. We will back off about 3dB as manufacture test due to bad background noise and interference in our production line. 3.5 Antenna Electrical Specification Parameter Operating frequency range Antenna gain (max) 3.6 Antenna Pattern Main port Typical 2400 ~ 2500 TBD Units MHz TBD Frequency
(MHz) 2412 2442 2472 Aux port Frequency
(MHz) 2412 2442 2472 Vertical Horizon Peak gain
(dBi) TBD Average gain
(dBi) TBD Peak gain
(dBi) TBD Average gain
(dBi) TBD TBD TBD TBD TBD TBD TBD TBD TBD Vertical Horizon Peak gain
(dBi) TBD Average gain
(dBi) TBD Peak gain
(dBi) TBD Average gain
(dBi) TBD TBD TBD TBD TBD TBD TBD TBD TBD 9 3.7 Return Loss Measurement for S11 COMPANY CONFIDENTIAL Return Loss Measurement for S11 Main antenna Aux antenna
-20.536dB@2412MHz
-27.920dB@2442MHz
-38.556dB@2484MHz
-17.771dB@2412MHz
-26.397dB@2442MHz
-19.879dB@2484MHz Main antenna Aux antenna Remark: the return loss measurement is base on air without any materials. 10 COMPANY CONFIDENTIAL 3.8 Radiated Emission Remark: we will provide the official regulatory test report from 3rd party lab. 4. Product Requirements 4.1 Hardware Requirements Form factor Host Interface PCB Antenna connector 40 mm x40mm module with 8-pin B.T.B connector USB2.0 interface 4-layer design RF switch connector 4.2 Hardware Architecture The T77H332.XX IEEE802.11b/g/n module is based on Marvell 88W8782UB0-NAP2C000 solution that is provide the combined functions of DSSS and OFDM baseband modulation, MAC, CPU, OTP (one time programmable) memory, host interfaces, power management unit (PMU) and direct conversion WLAN RF radio. This module is powered from the host
(3.3V) and interfaces to the host with USB 2.0 signals and with two printed antennas for diversity and one on-board 40 MHz XTAL. The functional block diagram is shown as below. 11 Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions:
(For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be 1 installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 2878D-
T77H332. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 2878D- T77H332". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2 Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: MCLT77H332. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Europe EU Declaration of Conformity ThisdevicecomplieswiththeessentialrequirementsoftheR&TTEDirective1999/5/EC.Thefollowingtestmethodshavebeen appliedinordertoprovepresumptionofconformitywiththeessentialrequirementsoftheR&TTEDirective1999/5/EC:
EN609501:2006+A11:2009+A1:2010+A12:2011 SafetyofInformationTechnologyEquipment EN62311:2008 Assessmentofelectronicandelectricalequipmentrelatedtohumanexposurerestrictionsforelectromagneticfields(0 Hz300GHz)
(IEC62311:2007(Modified)) EN300328V1.8.1:2012 ElectromagneticcompatibilityandRadiospectrumMatters(ERM);WidebandTransmissionsystems;Datatransmission equipmentoperatinginthe2,4GHzISMbandandusingspreadspectrummodulationtechniques;HarmonizedENcovering essentialrequirementsunderarticle3.2oftheR&TTEDirective EN3014891V1.9.2:2011 ElectromagneticcompatibilityandRadioSpectrumMatters(ERM);ElectroMagneticCompatibility(EMC)standardforradio 3 equipmentandservices;Part1:Commontechnicalrequirements EN30148917V2.1.12009 ElectromagneticcompatibilityandRadiospectrumMatters(ERM);ElectroMagneticCompatibility(EMC)standardforradio equipmentandservices;Part17:Specificconditionsfor2,4GHzwidebandtransmissionsystemsand5GHzhighperformance RLANequipment NationalAuthoritieswereinformedaccordingtoArticle6.4ofFrequencyNotification. SpecialRequirementsareconsidered.TheproductislabeledwithCEMarking. esky
[Czech]
Dansk
[Danish]
Deutsch
[German]
Eesti
[Estonian]
English Espaol
[Spanish]
[Greek]
Franais
[French]
Italiano
[Italian]
Latviski
[Latvian]
Lietuvi
[Lithuanian]
Nederlands
[Dutch]
Malti
[Maltese]
[Jmno vrobce] tmto prohlauje, e tento [typ zazen] je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Undertegnede [fabrikantens navn] erklrer herved, at flgende udstyr
[udstyrets typebetegnelse] overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hiermit erklrt [Name des Herstellers], dass sich das Gert [Gertetyp] in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Kesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tp = type of equipment] vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
[name of manufacturer] [type of equipment]
1999/5/. Par la prsente [nom du fabricant] dclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o [name of manufacturer / izgatavotja nosaukums] deklar, ka [type of equipment / iekrtas tips] atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo [manufacturer name] deklaruoja, kad is [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]
jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm 4 fid-Dirrettiva 1999/5/EC. Alulrott, [gyrt neve] nyilatkozom, hogy a [... tpus] megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Niniejszym [nazwa producenta] owiadcza, e [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
[Nome do fabricante] declara que este [tipo de equipamento] est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE.
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES.
[Meno vrobcu] tmto vyhlasuje, e [typ zariadenia] spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES.
[Valmistaja = manufacturer] vakuuttaa tten ett [type of equipment = laitteen tyyppimerkint] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hrmed intygar [fretag] att denna [utrustningstyp] str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Magyar
[Hungarian]
Polski
[Polish]
Portugus
[Portuguese
]
Slovensko
[Slovenian]
Slovensky
[Slovak]
Suomi
[Finnish]
Svenska
[Swedish]
5
This product uses the FCC Data API but is not endorsed or certified by the FCC