submitted | available | document details (if available) | source link |
---|---|---|---|
December 19 2016 | December 19 2016 | WC0FR2601_SPC_V1.4_161010 Administrator PDFCreator 2.2.1.0 |
various | User Manual 1 | Users Manual | 289.73 KiB | December 19 2016 |
PRODUCT SPECIFICATION Version 1.4 IEEE 802.11 a/b/g/n/ac 2T/2R Dual Band USB Module Model Number: WC0F2601 2.4G channel 1-11 5G channel 36-48 149-165 Custom Approval Section Custom Name Department Approval Date DESIGN CHECK 20161010 20161010 APPROVAL 20161010 PRODUCTS SPECIFICATION WC0FR2601 Document revision history Revision Date Approved by Remarks Version 1.0 2016-07-11 Version 1.1 2016-07-12 Version 1.2 2016-08-06 Version 1.3 2016-09-18 Version 1.4 2016-10-10 Draft Change 8 PIN to 10 PIN Change Mechanical Dimensions 25*45mm to 47*30mm 1Change function block diagram 2Change the 5G receive Sensitivity. 3Change Mechanical Dimensions 4Change SMT connector spec 5Change antenna spec 1 Change antenna spec 2 Update BOM PAGE 2 OF 09 Version 1.4 PRODUCTS SPECIFICATION 1. General Description This document is to specify the product requirements for 802.11a/b/g/n/ac USB Module. This Card is based on Realtek RTL8812AU chipset that complied with IEEE 802.11b/g/n/ac Draft 3.0 compatible WLAN ,and it is also backward complied with IEEE 802.11a standard from 5.15~5.825GHz wideband and IEEE 802.11b/g standard from 2.4000~2.4835GHz. It can be used to provide up to 54Mbps for IEEE 802.11a and IEEE 802.11g,11Mbps for IEEE 802.11b and 300Mbps for IEEE 802.11n and 866.7Mbps for IEEE 802.11ac to connect your wireless LAN. WC0FR2601 With seamless roaming, fully interoperability and advanced security with WEP standard, 802.11 a/b/g/n/ac USB Module offers absolute interoperability with different vendors 802.11a/b/g/n/ac.Access Points through the wireless LAN. 2. Features
Compatible with IEEE 802.11a standard to provide wireless 54Mbps data rate.
Compatible with IEEE 802.11b standard to provide wireless 11Mbps data rate.
Compatible with IEEE 802.11g standard to provide wireless 54Mbps data rate.
Compatible with IEEE 802.11n standard to provide wireless 300Mbps data rate.
Compatible with IEEE 802.11ac standard to provide wireless 866.7Mbps data rate.
Operation at 2.4~2.5GHz and 5.15~5.825GHz frequency band to meet worldwide regulations
Provides simple legacy and 20MHz/40MHz/80MHz co-existence mechanisms to ensure backward and network compatibility.
Supports infrastructure networks via Access Point and ad-hoc network via peer-to-peer communication
Supports IEEE 802.11i (WPA and WPA2), WAPI,. enhanced security
Friendly user configuration and diagnostic utilities
Drivers support Windows XP,Vista.Win7
High speed USB 2.0 interface
ROHS compliant PAGE 3 OF 09 Version 1.4 WC0FR2601 PRODUCTS SPECIFICATION 3. Application Diagrams 3.1 Functional Block Diagram 3.2 General Requirements 3.2.1 IEEE 802.11b Section Feature 3.2.1.1 3.2.1.2 3.2.1.3 Standard Radio and Modulation Schemes Operating Frequency 3.2.1.4 Channel Numbers 3.2.1.5 3.2.1.6 Data Rate Media Access Protocol 3.2.1.7 Transmitter Output Power at Antenna Connector Detailed Description IEEE 802.11b DQPSK , DBPSK , DSSS , and CCK 2400 2483.5MHz ISM band 11 channels for United States 13 channels for Europe Countries 14 channels for Japan 11,5.5,2,and 1Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain,Data Rate and at room Temp. 25
+19 dBm at 1Mbps
+18 dBm at 2Mbps
+17 dBm at 5.5Mbps
+16 dBm at 11Mbps PAGE 4 OF 09 Version 1.4 PRODUCTS SPECIFICATION 3.2.1.8 Receiver Sensitivity at Antenna Connector 3.2.2 IEEE 802.11g Section Feature 3.2.2.1 3.2.2.2 3.2.2.3 Standard Radio and Modulation Type Operating Frequency 3.2.2.4 Channel Numbers 3.2.2.5 3.2.2.6 3.2.2.7 3.2.2.8 Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector 3.2.3 IEEE 802.11a Section 3.2.3.1 Feature Standard Radio and Modulation Type 3.2.3.2 3.2.3.3 Operating Frequency 3.2.3.4 Channel Numbers 3.2.3.5 3.2.3.6 3.2.3.7 3.2.3.8 Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector Typical Sensitivity at Which Frame(1000-byte PDUs)Error WC0FR2601 Rate=8%
-88 dBm at 1Mbps
-82 dBm for 11Mbps Detailed Description IEEE 802.11g QPSK , BPSK , 16QAM ,64QAM with OFDM 2400 2483.5MHz ISM band 11 channels for United States 13 channels for Europe Countries 13 channels for Japan 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at roomTemp. 25
+18dBm at 6Mbps
+14dBm at 54Mbps Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25
-86 dBm at 6Mbps
-73 dBm at 54Mbps Detailed Description IEEE 802.11a QPSK , BPSK , 16QAM ,64QAM with OFDM 5.15~5.35GHz and 5.725~5.825GHz for US and Canada 5.15~5.35GHz and 5.47~5.725GHz for Japan 5.15~5.35GHz and 5.47~5.725GHz for Europe 5.725~5.825GHz for China 12 non-overlapping channels for US and Canada 8 non-overlapping channels for Japan 19 non-overlapping channels for Europe 4 non-overlapping channels for China 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at roomTemp. 25
+18 dBm at 6Mbps
+14 dBm at 54Mbps Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25
-83 dBm at 6Mbps
-71 dBm at 54Mbps PAGE 5 OF 09 Version 1.4 PRODUCTS SPECIFICATION 3.2.4 IEEE 802.11n Section 3.2.4.1 Feature Standard 3.2.4.2 3.2.4.3 Radio and Modulation Type Operating Frequency Detailed Description IEEE 802.11n BPSK , QPSK , 16QAM ,64QAM with OFDM 2.4GHz band:2400 ~ 2483.5MHz 5GHz and:5150 ~ 5825MHZ WC0FR2601 MCS GI=800ns GI=400ns 20MHz 40MH 20MHz 40MHz 3.2.4.4 Data Rate 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 6.5 13 19.5 26 39 52 58.5 65 13 26 39 52 78 104 117 130 13.5 27 40.5 54 81 108 121.5 135 27 54 81 108 162 216 243 270 7.2 14.4 21.7 28.9 43.3 57.8 65.0 72.2 14.4 28.9 43.3 57.8 86.7 115.6 130 144.4 15 30 45 60 90 120 135 150 30 60 90 120 180 240 170 300 3.2.4.5 Media Access Protocol CSMA/CA with ACK 3.2.4.6 Transmitter Output Power at Antenna Connector Typical RF Output Power (tolerance2dB) at each RF chain,Data Rate and at roomTemp. 25 2.4GHz Band/HT20 18 dBm at MCS0 12 dBm at MCS7 5GHz Band/HT20 18 dBm at MCS0 12 dBm at MCS7 2.4GHz Band/HT40 18 dBm at MCS0 12 dBm at MCS7 5GHz Band/HT40 18 dBm at MCS0 12 dBm at MCS7 Typical Sensitivity at each RF chain at Which Frame (1000-byte PDUs) Error Rate=10% and at room Temp. 25 3.2.4.7 Receiver Sensitivity at Antenna Connector 2.4GHz Band/HT20
-86 dBm at MCS0
-70 dBm at MCS7 2.4GHz Band/HT40
-83 dBm at MCS0
-66 dBm at MCS7 PAGE 6 OF 09 Version 1.4 PRODUCTS SPECIFICATION 5GHz Band/HT20 5GHz Band/HT40 WC0FR2601
-83 dBm at MCS0/8
-81 dBm at MCS0/8
-68 dBm at MCS7/15
-64 dBm at MCS7/15 3.2.5 IEEE 802.11ac Section 3.2.5.1 Feature Standard Radio and Modulation Type 3.2.5.2 3.2.5.3 Operating Frequency 3.2.5.4 Channel Numbers 3.2.5.5 3.2.5.6 Data Rate Media Access Protocol Detailed Description IEEE 802.11ac QPSK , BPSK , 16QAM ,64QAM,256QAM with OFDM 5.15~5.35GHz and 5.725~5.825GHz for US and Canada 5.15~5.35GHz and 5.47~5.725GHz for Japan 5.15~5.35GHz and 5.47~5.725GHz for Europe 5.725~5.825GHz for China 12 non-overlapping channels for US and Canada 8 non-overlapping channels for Japan 19 non-overlapping channels for Europe 4 non-overlapping channels for China at most 866.7 Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at roomTemp. 25 3.2.5.7 Transmitter Output Power at Antenna Connector HT20 18 dBm at MCS0 12 dBm at MCS7 11 dBm at MCS8 HT80 HT40 18 dBm at MCS0 12 dBm at MCS8 11 dBm at MCS9 3.2.5.8 Receiver Sensitivity at Antenna Connector 18 dBm at MCS0 12 dBm at MCS8 11 dBm at MCS9 Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25 5GHz Band / HT20 5GHz Band / HT40
-63 dBm at MCS8
-57 dBm at MCS9 5GHz Band / HT80
-56 dBm at MCS9 PAGE 7 OF 09 Version 1.4 PRODUCTS SPECIFICATION 4. Electrical and Thermal Characteristics 4.1 Temperature Limit Ratings WC0FR2601 Minimum Maximum
-40 0 0
+80 60 125 Units Detailed Description Operating Voltage Current Consumption Form Factor and Interface High Speed USB2.0 Interface ANT1: IPEX connector ANT2: Metal antenna 3.3V10%
1100mA Parameter Storage Temperature Ambient Operating Temperature Junction Temperature 4.2 General Section 4.2.1 Feature Antenna Type 4.2.2 4.2.3 4.2.4 4.3 Software Driver Windows XP/ WinCE/ Vista,/ Win7, Linux, MAC Security 64/128-bits WEP, WPA, WPA2 4.4 Mechanical Requirements 4.4.1 4.4.2 4.4.3 Feature Length Width High Detailed Description 47mm 30mm 6.2mm(PCB:1mm) PAGE 8 OF 09 Version 1.4 PRODUCTS SPECIFICATION 5. Connector Definition 10-Pin 1.25 mm connectorHorizontal Type WC0FR2601 Pin 1 2 3 4 5 6 7 8 9 10 Definition VCC VCC D- D+ GND WL_Host_Wake Reset GND NC GND
(3.3V)
(3.3V)
(Internal pull-up
(Internal pull-up 10K Ohm) 100K Ohm) 6 Mechanical Dimensions
*TOLERANCES ARE +/-0.5mm UNLESS OTHERWISE SPECIFIED
*UNIT:mm PAGE 9 OF 09 Version 1.4 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This product uses the FCC Data API but is not endorsed or certified by the FCC