LC001 True Wireless Earphones user manual

 

105g11c 9 75*55mm True Wireless Earphones User Manual Product Overview Indicator Light Charging Port 1 1 Charging Box x3 Micro USB 3 Accessories Touch Button Silicone Earcaps Charging Needle Charging Box Earphones Earphones Silicone Earcaps x 3pair User manual Micro USB charging cable 3 2 2 2

,LED LED LED1S LED110 4

....Primary Secondary"LED LC001

....Primary :

SecondaryLED 55 1 LED 5 5 LR TWSLED5 LED 5() L 2 6

/

7 2

+/-

/

L L TWS R L TWS Instructions Power On Power on automatically when Remove earphone out of box please long press earphone function button for 2s to turn on, if connect timeout or distance. Power O Put it into the charging box (without button o), the red LED is long bright, and the device is o. Charge Earphone Charging: put the earphone into the charging box and automatically enter the charging state. The red LED is on , indicating charging. After full charged, the green LED goes o for 1S Charging box charging:

Red light on, indicates low power. Please charge the charging box in time. Green light long on ,indicates full charged. Please stop charging. Battery State When power is low, red led light ashes twice every 10 seconds. Please charge the box in time, if earphone cant be turned o in the case. Connect Mobile Phone 4 Connection Take the earphone out of the box. When hear "Dong", it means power on. The primary earphone prompts: "primary", the secondary one prompts:

"secondary". Earphones LED lights ash red and green alternately, waiting for connection. Turn on the device bluetooth, search and connect the device

"LC001". First pairing mode Remove the headset from the case, when hear prompt tone, double-click on the left and right ear touch keys at the same time, will hear the primary headset prompts: "primary", secondary headphone ": secondary". Then use mobile phone to connect bluetooth, the headset LED lights ash red and green alternately, pairing time lasts for 5 minutes. If not connected, the device will shut down. Automatic Reconnection After rst paired, the earphone will automatically reconnect to the most recently connected one when removed from case. If not connected to the historical device for 1 time, the device will enter to search bluetooth pairing state, and the headphone LED light will ash red and green alternately; The device without connected after ve minutes will enter into shutdown state. 5 Master-Slave Denition Default factory Settings: the primary R, L is secondary. The primary one taken out is manually reconnected outside the case, and the manual operation is the primary. Distance Connection Master-slave earphone distance Secondary earphone on the table, take the primary earphone and mobile phone to the distance, the primary earphone continues to use, the secondary ear enters into reconnecting state mode. Secondary earphone LED lights ash alternately red and green, if not connected to the primary earphone within 5 minutes, secondary earphone will close down. Binaural Distance Put earphones in the overrange distance from phone. The earphones will enter into the reconnecting state, and the LED light will ash red and green alternately. If not connected to phone within 5 minutes, earphones will close down. Start The Phone System's Voice Assistant Double click the earphone touch button ( use L earphone alone),Bluetooth connection, not phone mode. 6 Clear Connection Record First put both earphones into pairing state, then three strikes, the last strike is more than 2s, nally power o. Call Status Or Play Music Double Click Long press button 2s Volume+/-

Play/Pause Double Click "L/R"

Double Click "L"

Double Click Touch Button 7 Left Right Answer The Phone Hang Up Reject a Call Mobile Operation Double touch the right keyTWS connection mode) Touch the touch keyuse R alone double touch the touch keyuse L alone Double touch left touch button

(TWS connection mode)

(Cr(VI))

(Pb)

(Hg)

(Cd) SJ/T 11364 O GB/T 26572 X GB/T 26572 8 SN

(PBB)

(PBDE)

!

, FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radic communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, 8 the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. CE Hereby, VOC declares that the radio equipment type True Wireless Earphones is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.vocacoustic.com/

FCC Statement 15.19 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 15.21 Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. 15.105(b) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. FCC ID: 2ATV4LC001 IC : 25216-LC001