MTGW01W MeshTek Gateway UM Users Manual

.. User Manual LightLink GENERAL DESCRIPTION iLumi LightLink is an IoT Gatway / Router, it allows users to control ilumi devices (iLumi SmartBulb, iLumi SmartStrip, etc) from smart device from anywhere from the world. It consists of ilumi MeshTek-H52 bluetooth module for communication with ilumi devices and WiFi module for communication to and from the cloud. Block Diagram 3.3V MeshTek-H52 BLE Module SPI NAND FLASH DC DC Circuit Input 5V, 1A Output 3.3V, 1.5A 3.3V USB Lima Module

(WiFi Module) Ethernet Transformer Ethernet

(RJ45 Connector) Reset Switch

& System led Micro USB

(Host USB) 5V Wall Mount USB Adapter 100VAC 240VAC ilumi Solutions Inc www.ilumisolutions.com P a g e 1 | 4 LightLink Package Contents iLumi LightLink 5VDC USB Adapter Micro USB Cable Ethernet Cable Quick Installation Guide Interfaces Installation Plug the usb cable to the adapter and LighLink micro usb socket Plug adapter to the AC wall socket and turn on the mains supply Power on led will turn on indicating device is powered and booting up Download the ilumi app Turn on Bluetooth on your smart device Follow the instructions on the app and setup LightLink Ilumi app will detect LightLink ilumi solutions, inc. www.ilumisolutions.com P a g e 2 | 4 LightLink REGULATORY APPROVAL a. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver connected Consult the dealer or an experienced radio/TV technician for help FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Important Note: FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. b. IC compliance This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be chosen in such a way that the equivalent isotropically radiated power (e.i.r.p.) is not more than that is necessary for successful communication. Important Note: IC Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. ilumi solutions, inc. www.ilumisolutions.com P a g e 3 | 4 LightLink c. Conformit aux norms dIC Cet appareil est conforme la(aux) norme(s) RSS sans licence dIndustry Canada. Son utilisation est soumise aux deux conditions suivantes:

1. Cet appareil ne doit pas causer dinterfrences et 2. il doit accepter toutes interfrences reues, y compris celles susceptibles davoir des effets indsirables sur son fonctionnement. Conformment aux rglementations dIndustry Canada, cet metteur radio ne peut fonctionner qu laide dune antenne dont le type et le gain maximal (ou minimal) ont t approuvs pour cet metteur par Industry Canada. Pour rduire le risque dinterfrences avec dautres utilisateurs, il faut choisir le type dantenne et son gain de telle sorte que la puissance isotrope rayonne quivalente (p.i.r.e) ne soit pas suprieure celle requise pour obtenir une communication satisfaisante. Note importante: dclaration d'exposition au rayonnement IC Cet quipement respecte limites dexposition aux rayonnements IC RSS-102 dfinies pour un environnement non contrl. Il doit tre install et utilis en maintenant une distance minimum de 20 cm entre le radiateur et votre corps. les FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. In order to comply with RF exposure requirements, a minimum separation distance of 20 cm must be maintained between the user's body and the smart signal converter (including the antenna). ilumi solutions, inc. www.ilumisolutions.com P a g e 4 | 4