| submitted | available | document details (if available) | source link |
|---|---|---|---|
| April 26 2016 | October 23 2016 |
| various | User manual | Users Manual | 1.36 MiB | April 26 2016 / October 23 2016 |
I ri d i u m C o re 9 5 2 3 / 9 52 3 N Pr o d u c t D e ve l o p e r ' s Gu i d e I r i d i u m C o m m u n i c a t i o n s , I n c . P r o p r i e t a r y & C o n f i d e n t i a l I n f o r m a t i o n Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 LEGAL DISCLAIMER AND CONDITIONS OF USE This document contains information for the Iridium Core 9523/9523N (Product) and is provided as is. The purpose of providing such information is to enable Value Added Resellers and Value Added Manufacturers (collectively, Product Developer(s)) to understand the Product and how to integrate it into a wireless solution. Reasonable effort has been made to make the information in this document reliable and consistent with specifications, test measurements and other information. However, Iridium Communications Inc. and its affiliated companies, directors, officers, employees, agents, trustees or consultants (Iridium) assume no responsibility for any typographical, technical, content or other inaccuracies in this document. Iridium reserves the right in its sole discretion and without notice to you to change Product specifications and materials and/or revise this document or withdraw it at any time. This document is provided in conjunction with the purchase of the Product and is therefore subject to the Product Sales Terms and Conditions set forth at http://www.Iridium.com/support/library/Legal Notices.aspx. The Product Developer assumes any and all risk of using the Product specifications and any other information provided. Your use of this document is governed by your Partner Agreement with Iridium. Please review your Partner Agreement and the Iridium Product Sales Terms and Conditions that govern your relationship with Iridium. This document is strictly Proprietary and Confidential to Iridium. Consistent with your Partner Agreement with Iridium, you may not this document (or any portion thereof) to others without express written permission from Iridium. Any violation of your Agreement's Proprietary and Confidentiality obligations shall result in remedies to the fullest extent available to Iridium at law or in equity. IRIDIUM MAKES NO REPRESENTATIONS, GUARANTEES, CONDITIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED REPRESENTATIONS, GUARANTEES, CONDITIONS OR WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, SATISFACTORY QUALITY, NON-INTERFERENCE, ACCURACY OF INFORMATIONAL CONTENT, OR ARISING FROM A COURSE OF DEALING, LAW, USAGE, OR TRADE PRACTICE, USE, OR RELATED TO THE PERFORMANCE OR NONPERFORMANCE OF ANY PRODUCTS AND/OR SERVICES ACCESSORIES, FACILITIES OR SATELLITE SERVICES OR INFORMATION EXCEPT AS EXPRESSLY STATED IN THIS DOCUMENT AND/OR THE PRODUCT AND/OR SATELLITE SERVICE DOCUMENTATION. ANY OTHER STANDARDS OF PERFORMANCE, GUARANTEES, CONDITIONS AND WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. THIS DISCLAIMER AND EXCLUSION SHALL APPLY EVEN IF THE EXPRESS LIMITED WARRANTY CONTAINED IN SUCH DOCUMENTATION FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT SHALL IRIDIUM BE LIABLE, REGARDLESS OF LEGAL THEORY, INCLUDING WITHOUT LIMITATION CONTRACT, EXPRESS OR IMPLIED WARRANTY, STRICT LIABILITY, GROSS NEGLIGENCE OR NEGLIGENCE, FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THIS DOCUMENT, IF ANY. NOR SHALL IRIDIUM BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF PRIVACY, LOSS OF USE, LOSS OF TIME OR INCONVENIENCE, LOSS OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSS CAUSED BY THE PRODUCT/SERVICE (INCLUDING HARDWARE, SOFTWARE AND/OR FIRMWARE) AND/OR THE IRIDIUM SATELLITE SERVICES, OR ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCT/SERVICE
(INCLUDING HARDWARE, SOFTWARE AND/OR FIRMWARE) AND/OR THE IRIDIUM SATELLITE SERVICES TO THE FULLEST EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW AND WHETHER ADVISED OF THE POSSIBILITIES OF SUCH DAMAGES. IRIDIUM IS NOT LIABLE FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU FOR A THIRD PARTY. Your use of the information contained in this Guide is restricted to the development activity authorized under the agreement(s) between you and Iridium, and is otherwise subject to all Iridium Communications, Inc. Proprietary & Confidential Information Page 2 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 applicable terms and conditions of such agreement(s), including without limitation software license, warranty, conditions of use and confidentiality provisions. Export Compliance Information This Product is controlled by the export laws and regulations of the United States of America. The U.S. Government may restrict the export or re-export of this Product to certain individuals and/or destinations. Diversion contrary to U.S. law is prohibited. For further information, contact the U.S. Department of Commerce, Bureau of Industry and Security or visit www.bis.doc.gov. Revision History Revision Date 1.0 2.0 2.3 2.5 Nov 11, 2015 May 9, 2011 Jul 26, 2011 Sep 12, 2011 2.6 Oct 11, 2011 2.7 Oct 17, 2011 3.0 3.1 Oct 21, 2011 Oct 27, 2011 3.2 Feb 23, 2012 7.0 Aug 20, 2012 7.1 7.2 DRAFT2 Jul 29, 2014 Nov 17, 2015 7.2 DRAFT3 Jan 12, 2016 7.2 DRAFT4 Jan 28, 2016 Comment First Draft. Second Draft Following Internal Review Revision sent with Alpha prototype Developers Kit Revision sent with Beta prototype Developers Kit
- Added FCC and IC warning statements (sections 1.3 and 1.4)
- Removed reference to mounting screws in section 2.1 Dimensions and Layout
- Clarified screw/hole specifications in section 2.2 Field Application Board Mounting
- Unified formatting of examples and removed references to AT*Rn in section 8 Informative Examples
- Replaced reference to AT*F with AT*P0 in section 3.2.3 Power On/Off Control
- Added note on digital I/O ESD protection in section 3.1.2 User Connector Pin Allocation First published revision Added note on non-portable regulatory certification to section 1.2 Significantly reduced sections "Data/Fax Port" and "AT Interface" and added references to the ISU AT Command Reference. Removed sections "S-Register Definitions", "Summary of Result Codes",
"Informative Examples", and "Supported AT Commands" as this information is contained in the ISU AT Command Reference.
- Updated section Legal Disclaimer and Conditions of Use.
- Removed description of PCB digital audio ports as 15 bits in section 3.3 PCM Digital Audio since the ports use 16-bit PCM samples.
- Changed all references to the product to Iridium Core 9523
- Corrected section 4 sub-section numbering
- Revised introductory paragraph of section 2.3.2 Updated to include 9523N. For internal review. Incorporated comments from Mike Senzig. Updated in accordance with comments from the IEC 60950-1 safety testing at TUV (see Interim Test Summary_75932207_Issue1):
Clarified part numbering in section 2.1. Clarified number of power supplies and the nominal and maximum voltage and maximum current in section 3.2.1 and included recommendation to incorporate a current limiting device in the host application. Added details on requirements of the enclosure provided by the host product/application in section 2.2. Updated Declaration of Conformity. Updated in accordance with comments from the IEC 60950-1 safety testing at TUV (see Interim Test Summary_75932207_Issue2). Iridium Communications, Inc. Proprietary & Confidential Information Page 3 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Export Compliance Information This product is controlled by the export laws and regulations of the United States of America. The U.S. Government may restrict the export or re-export of this product to certain individuals and/or destinations. For further information, contact the U.S. Department of Commerce, Bureau of Industry and Security or visit www.bis.doc.gov. Iridium Communications, Inc. Proprietary & Confidential Information Page 4 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 3 2 2.1 2.1 2.2 2.3 1.1 1.2 1.3 1.1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Contents Revision History .......................................................................................................................................... 3 Contents ..................................................................................................................................................... 5 List of Abbreviations .................................................................................................................................. 6 Product Overview ............................................................................................................................... 7 1 Key Features .......................................................................................................................... 7 Iridium Core 9523/9523N Packaging and Regulatory Certification ....................................... 7 Software Revision .................................................................................................................. 8 Unauthorised Changes .......................................................................................................... 9 Radio Interference ................................................................................................................. 9 RF Exposure .......................................................................................................................... 9 FCC Class B Digital Device Notice ...................................................................................... 10 Labelling Requirements for the Host device ........................................................................ 10 CAN ICES-3 (B) / NMB-3 (B) ............................................................................................... 11 R&TTE Statement ................................................................................................................ 11 Reference ............................................................................................................................. 13 Physical Specification ..................................................................................................................... 14 Dimensions and Layout ....................................................................................................... 16 Part Numbering .................................................................................................................... 17 Field Application Board Mounting ........................................................................................ 18 Environmental ...................................................................................................................... 21 Environmental Specification ................................................................................................. 21 2.3.1 2.3.2 Environmental Tests ............................................................................................................ 21 Electrical Interfaces ......................................................................................................................... 23 User Connector .................................................................................................................... 23 User Connector Type ........................................................................................................... 23 User Connector Pin Allocation ............................................................................................. 24 DC Power Supply Interface .................................................................................................. 26 DC Power Supply Inputs ...................................................................................................... 26 Power On/Off Control, TRX_ON .......................................................................................... 27 Typical Power Usage Profile ................................................................................................ 27 PCM Digital Audio ................................................................................................................ 29 Port 1 .................................................................................................................................... 30 Port 2 .................................................................................................................................... 30 11Hz Signal for Manufacturing and Regulatory Testing ...................................................... 31 DPL port ............................................................................................................................... 31 Data/Fax port ....................................................................................................................... 31 SIM interface ........................................................................................................................ 31 GPIO Signals ....................................................................................................................... 32 Transmit power Control ........................................................................................................ 32 3.7.1 External GPS Receiver Switch ............................................................................................ 32 3.7.2 3.7.3 Modem/Handset Mode Select Signal .................................................................................. 32 RF Interface ....................................................................................................................................... 32 RF Connector Type .............................................................................................................. 32 Antenna Characteristics ....................................................................................................... 33 RF Interface Specifications .................................................................................................. 33 Radio Characteristics ........................................................................................................... 34 S-meter Performance ........................................................................................................... 34 AT Interface ....................................................................................................................................... 34 3.2.1 3.2.2 3.2.3 3.3.1 3.3.2 3.3.3 3.4 3.5 3.6 3.7 4.2 4.3 4.4 3.1.1 3.1.2 4.1.1 4.1 3.1 3.2 3.3 4 5 Iridium Communications, Inc. Proprietary & Confidential Information Page 5 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 List of Abbreviations Abbreviation Description CE CTS DC DCD DCE DSR DTE DTR ESD FA FCC GND GSS IC IMEI LBT MO Conformit Europene
(V.24 signal) Clear To Send. This signal is used to control the flow of data to the Iridium Core 9523 Direct Current
(V.24 signal) Data Carrier Detect Data Communications Equipment. In this Product, DCE refers to the Iridium Core 9523
(V.24 signal) Data Set Ready. This signal, from the Iridium Core 9523, indicates readiness to accept communication over the data port Data Terminal Equipment. In this Product, DTE refers to the FA
(V.24 signal) Data Terminal Ready. This signal, from the FA, requests the Iridium Core 9523 to accept communication over the data port Electro-static Discharge Field Application; the application controlling the Iridium Core 9523 Federal Communications Commission Ground Gateway SBD Subsystem (synonymous with ESS) Industry Canada International Mobile Equipment Identity L-Band Transceiver Mobile Originated MOMSN Mobile Originated Message Sequence Number MT Mobile Terminated MTMSN Mobile Terminated Message Sequence Number PCM RHCP RI RTS SBD SMS TBA UART VAM VAR VSWR Pulse Code Modulation Right Hand Circular Polarization
(V.24 signal) Ring Indicate. This signal, from the Iridium Core 9523, indicates that an MT message is present at the GSS
(V.24 signal) Request To Send. This signal is used to control the flow of data from the Iridium Core 9523. Short Burst Data Short Message Service To Be Advised Universal Asynchronous Receiver Transmitter Value Added Manufacturer Value Added Reseller Voltage Standing Wave Ratio Iridium Communications, Inc. Proprietary & Confidential Information Page 6 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 1 Product Overview 1.1 Key Features The Iridium Core 9523/9523N is a voice and data transceiver module for the Iridium global satellite network. It is designed to be integrated with field application (FA) hardware and software to produce a solution designed for a specific application or vertical market. These solutions drive a wide range of applications in industries such as Oil and Gas, Rail, Maritime, Aeronautical, Utilities and Government/Military. The Iridium Core 9523/9523N is designed to meet the regulatory requirements for approval for FCC, Canada, and CE assuming an antenna with a gain of ~3 dBi and adequate shielding. The Iridium Core 9523/9523N supports all Iridiums voice and data services. Applications can be built to use one or multiple services using the voice and data interfaces. The product provides the core transceiver module. All other functions and hardware such as SIM card reader, keypad, display, power supply antenna etc. must be provided by the Product Developer. The Iridium Core 9523/9523N consists of the following:
Iridium radio transceiver with 8 watt transmitter and dual receivers Call Processor function that implements the Iridium L-Band AIS protocol Coaxial RF connector for the antenna 40-way inter-PCB connector with the following interfaces:
Iridium speech Vocoder o Digital audio interfaces o DPL serial asynchronous control port o Serial asynchronous interface for SIM o Data/Fax port serial asynchronous data plus 6 control signals o GPIO control signals o Power The Iridium Core 9523N is a second generation version of the Iridium Core 9523 and is identical in form and function to the Iridium Core 9523. This document applies to both the Iridium Core 9523 and Iridium Core 9523N as indicated by the term Iridium Core 9523/9523N. Where the contents of this document apply specifically to either the Iridium Core 9523 or Iridium Core 9523N then this is indicated by the use of the terms Iridium Core 9523 and Iridium Core 9523N respectively. The Iridium Core 9523/9523N is described within this document as 9523/9523N and ISU. All of these terms refer to the same product. 1.2 Iridium Core 9523/9523N Packaging and Regulatory Certification The Iridium Core 9523/9523N is a regulatory approved daughter module transceiver that can be fitted within an enclosed host system. With appropriate external connections, the host system can be designed to meet full transceiver regulatory tests and sold as a Regulatory Certified product that meets CE, FCC and IC requirements. The Iridium Core 9523 is tested to the regulatory and technical certifications shown in Table 1. The Iridium Core 9523N is tested to the regulatory and technical certifications shown in Table 2. Iridium Communications, Inc. Proprietary & Confidential Information Page 7 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Regulatory Approvals Table 1: Iridium Core 9523 Regulatory and Technical Certifications Radio Tests EMC Tests Electrical /
Mechanical /
Operational Safety Tests CE ETSI EN 301 441 V1.1.1
(2000-05) ETSI EN 301 489-1 V1.8.1 (2008-04) ETSI EN 301 489-20 V1.2.1 (2002-11) EN60950-1:2006 Part 1 FCC FCC CFR47 parts 2, 15, and 25 EN61000-4-2 : 1995/A2 : 2001 Part 4.2 EN61000-4-3 : 2002 Part 4.3 EN61000-4-4 : 2004 EN61000-4-6 : 1996/A1 : 2001 Part 4.6 EN55022:2006 Industry Canada Regulatory Approvals RSS170 Issue 2, March, 2011 Table 2: Iridium Core 9523N Regulatory and Technical Certifications Electrical /
Radio Tests EMC Tests CE ETSI EN 301 441 V1.1.1
(2000-05) ETSI EN 301 489-1 V1.9.2 (2011-09) ETSI EN 301 489-20 V1.2.1 (2002-11) Mechanical /
Operational Safety Tests EN 60950-1:2006
/A12:2011/A2:2013 AS/NZS 60950.1:
2011/A1:2012 FCC CFR47 parts 2
(2014), 15B (2014), and 25
(2014) EN61000-4-2 : 2009 EN61000-4-3 : 2006+A2:2010 EN61000-4-4 : 2012 EN61000-4-6 : 2013 EN55022:2010 RSS170 Issue 3, Jul 2015 RSS-GEN Issue 4, Nov 2014 ICES-003 Issue 5, Aug 2012 FCC Industry Canada 1.3 Software Revision Product Developers should read this document in conjunction with the Software Release Notes relevant to the revision of the software that is loaded into their Iridium Core 9523/9523N. The software release notes are available on the Iridium for Partners section of the Iridium.com website. Iridium Communications, Inc. Proprietary & Confidential Information Page 8 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 There may be multiple software releases over the lifespan of the Iridium Core 9523/9523N. A software upgrade utility is provided with each software release. The utility runs on a Windows-compatible OS and will automatically upgrade the modem with the latest version. Production procedures for finished goods should ensure that the appropriate software release is loaded on each Iridium Core 9523/9523N module used. The software release loaded on a particular Iridium Core 9523/9523N module can be read out using the AT command interface. 1.1 Unauthorised Changes Iridium has not approved any changes or modifications to this device by the user. Any changes or modifications could void the users authority to operate the equipment. Iridium napprouve aucune modification apporte lappareil par lutilisateur, quelle quen soit la nature. Tout changement ou modification peuvent annuler le droit dutilisation de lappareil par lutilisateur. 1.1 Radio Interference This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that necessary for successful communication. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. 1.2 RF Exposure This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below: 3.0 dBi. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non contrl. L'antenne doit tre install de faon garder une distance minimale de 20 centimtres entre la Iridium Communications, Inc. Proprietary & Confidential Information Page 9 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 source de rayonnements et votre corps. Gain de l'antenne doit tre ci-dessous: 3.0 dBi. L'metteur ne doit pas tre colocalis ni fonctionner conjointement avec autre antenne ou autre metteur. 1.3 FCC Class B Digital Device Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. 1.4 Labelling Requirements for the Host device The host device shall be properly labelled to identify the modules within the host device. The certification label of the module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the FCC ID and IC of the module, preceded by the words
"Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows:
Iridium Core 9523 Contains FCC ID: Q639523 or Contains transmitter module FCC ID: Q639523 Contains IC: 4629A-9523 or Contains transmitter module IC: 4629A-9523 Iridium Core 9523N Contains FCC ID: Q639523N or Contains transmitter module FCC ID: Q639523N Contains IC: 4629A-9523N or Contains transmitter module IC: 4629A-9523N L'appareil hte doit tre tiquet comme il faut pour permettre l'identification des modules qui s'y trouvent. L'tiquette de certification du module donn doit tre pose sur l'appareil hte un endroit bien en vue en tout temps. En l'absence d'tiquette, l'appareil hte doit porter une tiquette donnant le FCC ID et le IC du module, prcd des mots Contient un module d'mission , du mot Contient ou d'une formulation similaire exprimant le mme sens, comme suit:
Iridium Core 9523 Contains FCC ID: Q639523 or Contains transmitter module FCC ID: Q639523 Contains IC: 4629A-9523 or Contains transmitter module IC: 4629A-9523 Iridium Communications, Inc. Proprietary & Confidential Information Page 10 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Iridium Core 9523N Contains FCC ID: Q639523N or Contains transmitter module FCC ID: Q639523N Contains IC: 4629A-9523N or Contains transmitter module IC: 4629A-9523N 1.5 CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-0031. Cet appareil numrique de classe B est conforme la norme canadienne ICES-0032. 1.6 R&TTE Statement Iridium Communications Inc. hereby declares that the 9523N is in compliance with the essential requirements and other relevant provisions of Directive1999/5/EC. A copy of the Declaration of Conformity is given below. 1Applicable to 9523N only. 2Applicable 9523N seulement. Iridium Communications, Inc. Proprietary & Confidential Information Page 11 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Iridium Communications, Inc. Proprietary & Confidential Information Page 12 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
1.7 Reference ITU-T Recommendation V.25ter, 08/95 ETS 300 642: Digital Cellular Telecommunications System (Phase 2); AT Command Set for GSM Mobile Equipment (GSM 07.07) ETS 300 585: Digital Cellular Telecommunications System (Phase 2); Use of DTE-DCE Interface SMS and CBS (GSM 07.05) ETS 300 520: Digital Cellular Telecommunications System (Phase 2) (GSM); Call Barring (CB) Supplementary Services Stage 1 (GSM 02.88) ETS 300 511: Digital Cellular Telecommunications System (Phase 2) (GSM); ManMachine Interface (MMI) of the Mobile Station (MS) (GSM 02.30) ETS 300 516: Digital Cellular Telecommunications System (Phase 2) (GSM); Call Waiting (CW) and Call Hold (HOLD) Supplementary Services; Stage 1 (GSM 02.83) ETS 300 557: Digital Cellular Telecommunications System (Phase 2) (GSM); Mobile radio interface; Layer 3 Specification (GSM 04.08) ETS 300 559: Digital Cellular Telecommunications System (Phase 2) (GSM); Point-to-Point (PP) Short Message Service (SMS) support on mobile radio interface (GSM 04.11) ETS 300 536: Digital Cellular Telecommunications System (Phase 2) (GSM); Technical realization of Short Message Service (SMS) Point-to-Point (PP) (GSM 03.40) ETS 300 537: Digital Cellular Telecommunications System (Phase 2) (GSM); Technical realization of Short Message Service Cell Broadcast (SMSCB) (GSM 03.41) ETS 300 515: Digital Cellular Telecommunications System (Phase 2) (GSM); Call Forwarding
(CF) Supplementary Services (GSM 02.82) 3GPP TS 27.007: 3rd Generation Partnership Project; Technical Specification Group Terminals;
AT command set for User Equipment (UE) Iridium Communications, Inc. Proprietary & Confidential Information Page 13 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 2 Physical Specification For illustrative purposes, pictures of the Iridium Core 9523 and Iridium Core 9523N, fitted with its aluminum shielding frame, are shown in Figure 1 and Figure 2 respectively. Figure 1: Photos of Iridium Core 9523 Top View Bottom View Left View Iridium Communications, Inc. Proprietary & Confidential Information Page 14 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Figure 2: Photos of Iridium Core 9523N Top View Bottom View Left View Iridium Communications, Inc. Proprietary & Confidential Information Page 15 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 2.1 Dimensions and Layout The overall dimensions of the Iridium Core 9523 and its weight are summarized in Table 3 and represented graphically in Figure 3. Table 3: Iridium Core 9523 Mechanical Dimensions Parameter Length Width Value 70.44 mm 36.04 mm Height (from FA board) 14.6 mm max (reservoir capacitors) 8.9 mm (screening can) Weight (approximate) 32g The Iridium Core 9523/9523N consists of a single PCB with components mounted on top and bottom sides. On the top side, there are three reservoir capacitors, the RF connector, and a screening can covering all the remaining circuits. The bottom side has a Molex 40-pin multi-way user interface connector. The bottom side does not have a screening can, but instead the PCB artwork has an exposed ground ring all around the edge of the board. This ground ring makes contact with an aluminum screening frame, attached to the Iridium Core 9523/9523N by four corner thread-forming screws. The tips of these screws protrude through the aluminum frame and act as alignment pins when mounting onto the FA board. The aluminum frame also has at its center a 1.0mm diameter alignment pin. There are a further four corner screw holes through the aluminum frame and PCB for securing the Iridium Core 9523/9523N to the FA board. The two height values provided in Table 3 do not include the height of the compressible gasket on the bottom of the Iridium Core 9523/9523N that will mate to the FA board. It is assumed that this gasket will compress to near zero thickness if screws are torqued sufficiently. Iridium Communications, Inc. Proprietary & Confidential Information Page 16 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Figure 3: Dimensions of the Iridium Core 9523/9523N
(Dimensions in millimeters) 2.1 Part Numbering The part numbers for the Iridium Core 9523/9523N are as shown in Table 4. The part number is stated on the product label. Table 4: Iridium Core 9523/9523N Part Numbering Model Iridium Core 9523 Iridium Core 9523N Part Number IRID0125X IRIDN0125X Iridium Communications, Inc. Proprietary & Confidential Information Page 17 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 2.2 Field Application Board Mounting The Iridium Core 9523/9523N is designed to be mounted to an FA board as illustrated in Figure 4. Figure 4: Illustration of mounting module to application board The FA board must have a socket mating to the Molex 40-pin multi-way user interface connector on the bottom of the Iridium Core 9523/9523N. See section 3.1.1 for the connector part number. The Molex connectors and aluminum frame set the separation between the Iridium Core 9523/9523N and FA boards at 2.5 mm. In order to meet type approval standards for EMC, the FA board should include a ground ring and a good ground layer on its top surface to act as the fifth side of the screening can. The layout of the mounting location for the Iridium Core 9523/9523N on the FA board including the locations and diameters of all nine holes, layout of the grounding ring, and identification of areas with different grounding requirements is shown in Figure 5. A CAD file showing this information in DXF format can be obtained from Iridium in order to assist layout of FA boards. The FA board must have screw holes lining up with the Iridium Core 9523/9523Ns four 1.8mm corner mounting screw holes. The Iridium Core 9523/9523N must be secured to the FA board with four M1.6x0.35 screws through these holes. The FA board must also have four corner alignment holes and one center alignment hole lining up, respectively, with the Iridium Core 9523/9523Ns four 1.6mm corner protruding screws and one 1mm center alignment pin. The screw holes should be at least 1.8mm and the alignment hole at least 1.2mm, but they may be made slightly larger for greater tolerance. In Figure 5 below, one of the screw holes is 2.08mm, providing the primary alignment, while the other three screw holes are 2.1mm. In the same figure, the center alignment hole is 1.3mm. These dimensions are recommendations; other dimensions may be used so long as the Iridium Core 9523/9523N is properly aligned with the user interface connector and ground trace. In Figure 4, area A of the FA board sits under sensitive analog circuitry on the Iridium Core 9523/9523Ns bottom side, and it is essential that no components or tracks on the FA board appear in this area; it must be filled entirely with a solid ground plane on the top layer of the FA board. Area D sits under digital and power circuits. Ideally, this will also be shielded with a solid ground plane. However, it is acceptable to place tracks and low-profile components in area D, so long as care is taken to avoid mechanical clashes and due consideration is taken of EMC issues. Iridium Communications, Inc. Proprietary & Confidential Information Page 18 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Area C contains the Molex user interface connector and should be free of surface copper. The FA board must provide a sufficient margin free of conductive elements around the Iridium Core 9523/9523N perimeter in order to avoid electrical shorts with the Iridium Core 9523/9523N. This is indicated by the SMT Placement Keepout Zone. Partner solutions must be provide sufficient clearance above the conductive capacitors and shield can on the top of the Iridium Core 9523/9523N to prevent an electrical short. When operating the Iridium Core 9523/9523N at ambient temperatures of 50C or greater, the external surface temperature of the Iridium Core 9523/9523N may exceed 70C. In the case where the ambient temperature in the host product incorporating the Iridium Core 9523/9523N can exceed 50C, the host product must prevent direct access to the Iridium Core 9523/9523N module by the end user/operator in order to comply with EN 60950-1 clause 4.5. It is recommended that Iridium Core 9523/9523N be powered from a Limited Power Supply (LPS)3 as detailed in EN60950-1 clause 2.5. Where this is not the case then the host product that incorporates the Iridium Core 9523/9523N must provide the electrical enclosure, mechanical enclosure and fire enclosure for the Iridium Core 9523/9523N in order to comply with EN60950-1 clause 1.7. 3 An LPS is a power supply where the maximum supply power is limited to 100VA. Iridium Communications, Inc. Proprietary & Confidential Information Page 19 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Figure 5: Mounting location dimensions and layout
(Dimensions in millimeters) Iridium Communications, Inc. Proprietary & Confidential Information Page 20 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 2.3 Environmental 2.3.1 Environmental Specification The environmental specifications of the Iridium Core 9523/9523N are summarized in Table 5 below. Table 5: Environmental Specifications Parameter Value Operating Temperature Range
-30C to +70C Operating Humidity Range Storage Temperature Range Storage Humidity Range 75% RH
-40C to +85C 93% RH 2.3.2 Environmental Tests An Iridium system that incorporates the Iridium Core 9523 has passed the tests listed in Table 6. The Iridium Core 9523N has passed the tests in Table 7. It is expected that a system incorporating the Iridium Core 9523/9523N designed according to this document should also pass these tests. Table 6: Iridium Core 9523 Environmental Tests Test Name Test Reference Test Description IEC Vibration (IEC60068-2-64) Mount unit to a vibration table and excite between 15 and 500 Hz Low Pressure (500.4 - II) Decrease pressure to 57.2 kPa (equivalent to 15,000 ft) at a rate not to exceed 10 m/s and hold for 1 hour High Temperature (501.4 - I) Over 24 hours, cycle the unit from 33C to 71C and back to 33C. Repeat 7 times. High Temperature (501.4 - II) Test is a subset of High Temperature 501.4 - Part I, focused on the first three cycles. MIL-STD-
810GF Low Temperature (502.4 - I) Soak unit for 24 hours at -45C Low Temperature (502.4 - II) Soak unit for 4 hours at -10C Temperature Shock (503.4 - I) Soak unit at -40C for 4 hours. Transfer to 85C chamber and soak additional 4 hours. Repeat 3 times. Each transfer from one temperature environment to the other should be made in less than 1 minute. Vibration (514.5 - I, Cat. 8) Secure unit to a vibration table and excite randomly from 15-2000 Hz at 0.01 - 0.03 g^2/Hz. Shock (516.4 - I) Expose unit to 3 shocks of 40g over approximately 11ms in each of 3 primary axes (9 total shocks). Iridium Communications, Inc. Proprietary & Confidential Information Page 21 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Table 7: Iridium Core 9523N Environmental Tests Test Name Test Reference Change of Temperature
(EN60068-2-14 2009) Mechanical Shock
(EN60068-2-27 2009) IEC Vibration
(EN60068-2-64 2008) Damp Heat Steady State
(EN60068-2-78 2012) Thermal Shock SAE J1455:2012 Section 4.1.3.2 Handling Drop Test SAE J1455:2012 Section 4.11.3.1 SAE J1455:2012 Section 4.10.4.2 Vibration Low Pressure Method 500.5 Procedure II - Operation/Air Carriage High Temperature Method 501.5 Procedure I Storage High Temperature Method 501.5 Procedure II - Operation Low Temperature Method 502.5 Procedure I Storage Low Temperature Method 502.5 Procedure II Operation Temperature Shock Method 503.5 Procedure I-C Humidity Method 507.5 Procedure II Aggravated Vibration Method 514.6 Procedure I General Vibration
(Category 8) Shock Method 516.6 Procedure I Functional Shock SAE MIL-STD-810G Five cycles of 1 hour each from -30C to +70C. Test Description Mount unit on a vibration table and excite with three half sine pulses in each of three axis (pulse peak amplitude:
10g, pulse duration: 11ms). Mount unit on a vibration table and excite from 5Hz to 20Hz at 0.96m2/s3 and from 21Hz to 500Hz at 0.96m2/s3 rolling of at -3dB per octave for 1 hour per axis in each of three axes. 40C, 93%RH for 4 days Five cycles of 2 hours each from -40C to +85C. Drop from a height of 1m onto a concrete surface, one time in each of the three mutually perpendicular planes
(three drops in total). Mount unit on a vibration table and excite from 10 Hz to 40 Hz at 0.02g/Hz and from 40 Hz to 500 Hz at 0.02g/Hz dropping of at -6 dB per octave for 1 hour per axis in each of three axes. Decrease pressure to 57.2 kPa (equivalent to 15,000 feet) at a rate not to exceed 10 m/s at a temperature of 23C 3C and hold for 1 hour. Over 24 hours, cycle the unit from 35C to 71C and back to 35C. Repeat 7 times. This test is a subset of the High Temperature test
(Method 500.5, Procedure I) in which the operation is verified at 71C over the first 3 cycles of Procedure I. Ramp from ambient conditions to -45C 2C in 1 hour. Soak at -45C for 24 hours. Ramp from -45C to ambient conditions in 1 hour. Ramp from ambient conditions to -10C 2C in 1 hour. Soak at -10C for 24 hours. Ramp from -10C to ambient conditions in 1 hour. Soak at -40C for 4 hours. Transfer to +85C and soak for an additional 4 hours. Repeat 4 times (4 cold to hot transitions and 4 hot to cold transitions). Held at 95% RH with the ambient temperature changed from 30C to 60C and then down to 20C over a 48 hour cycle, with the cycle repeated 5 times. Secure unit to a vibration table and excite randomly with the following profile: Category 8:15-2000 Hz, L0=0.30 g2/Hz, f0 = 68 Hz, 1 hour per axis in each of 3 axes. Expose unit to 3 shocks of 40g over approximately 11ms in +/- direction of each of the 3 primary axes (18 total shocks). Iridium Communications, Inc. Proprietary & Confidential Information Page 22 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Electrical Interfaces The following subsections contain information for the electrical interfaces of the Iridium Core 9523/9523N for the non-RF connections. The RF interface is covered in Section 0. 3.1 User Connector Table 8 lists the connections to the Iridium Core 9523/9523N on the user connector. Signal group PCM Digital Audio Table 8: Signal Groups on User Connector Signal function Two synchronous serial interfaces carrying 16-bit, 8 kHz sample rate PCM audio data Each port has 4 wires data in each direction, clock and frame signals Only one digital audio port is in use at any time Port 1 has a secondary function during factory testing, to carry the 90ms frame synchronization from the test equipment DPL port Serial asynchronous control interface 2 wires data in each direction Data/Fax port Serial asynchronous control interface 8 wires data in each direction plus control signals The full set of control signals may be used for a Data/Fax port SIM interface Standard SIM signals 5 wires data, clock, reset, enable, voltage select Power Battery Supply to Iridium Core 9523/9523N GPIO, antenna configuration Other GPIO 5 power pins 3x battery voltage and 2x boost voltage 6 grounds 1 boost regulator control line (PA_BOOST_EN) 2 wires ANT_DET_PWR and FULL_POWER_EN. Signals provided as a mechanism to restrict the transmitted power for example in order to meet SAR standards. 2 wires TX_ACTIVE which may be used as an output to indicate when the transmitter is active, and LBT_HSTB which determines the operating mode of the software on the Iridium Core 9523/9523N. 3.1.1 User Connector Type The connector on the Iridium Core 9523/9523N is a 40-way, 0.5 mm pitch Molex low-profile header connector, part number 54102-0404. This connector provides the ability for a stackable board-to-board configuration, allowing connection to the host system motherboard via a mating 53885-0408 socket. Data sheets on these connectors can be found at: http://www.molex.com Iridium Communications, Inc. Proprietary & Confidential Information Page 23 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Pin numbering schemes for the Molex connectors on the Iridium Core 9523/9523N and the host FA board are shown in Figure 6 (both pictures show the pin-out when looking down onto the boards). Figure 6: Pin numbering scheme for User Connector Molex 54102-0404 on Iridium Core 9523/9523N:
Molex 53885-0408 on FA PCB:
Figure 7 provides a reference for the pin designation and shows the connectors location and rotation with respect to the corner of the Iridium Core 9523/9523N board. This view is for illustrative purposes only. This view designation is when looking into the user connector towards the Iridium Core 9523/9523N. Figure 7: User Connector Pin Number Designation 3.1.2 User Connector Pin Allocation The user connector is a 2-row 40-way header. Individual pin assignments are shown in Table 9 and the limits for the digital signals are listed in Table 10. Multiple supply grounds are provided and all supply rails and supply grounds are required to be connected to the power supply in order to limit the current on any one pin. Note that the Iridium Core 9523/9523N provides limited ESD protection on its digital I/O signals: Human Body Model 2kV and Machine Model 200V ESD protection. Partners should design their FA boards to include appropriate ESD protection on these signals. Iridium Communications, Inc. Proprietary & Confidential Information Page 24 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Pin No. Signal Name 0V 0V 1 CODEC_PCMCLK 2 CODEC_PCMIN 3 CODEC_PCMSYNC 4 CODEC_PCMOUT 5 6 7 UC_DACLK 8 UC_DATX 9 UC_DAFS 10 UC_DARX 11 0V 12 0V 13 DPL_RXD 14 DPL_TXD 15 DF_RX 16 DF_TX 17 DF_CTS 18 DF_DCD 19 DF_DSR 20 DF_RI 21 DF_RTS 22 DF_DTR 23 SIM_1V8_3V 24 SIM_CLOCK 25 SIM_ENABLE 26 SIM_RESET 27 SIM_DATA_IO 28 FULL_POWER_EN 29 ANT_DET_PWR 30 LBT_HSTB 31 TX_ACTIVE 32 TRX_ON 33 PA_BOOST_EN 34 0V 35 0V 36 VBAT 37 VBOOST 38 VBAT 39 VBOOST 40 VBAT Table 9: User Connector Pin Allocation Signal direction
(WRT modem) Signal function Signal group Out Out Out In Out Out Out In In Out Out In Out Out Out Out In In Out Out Out Out Bidir In Out In Out In Out In In In In In Clock Data from modem Frame Sync Data to modem Ground Ground Clock Data from modem Frame Sync Data to modem Ground Ground Data to modem Data from modem Data from modem Data to modem Clear to Send Carrier Detect Data Set Ready Ringing Indication Request to Send Data Terminal Ready Voltage select Clock Enable Reset Data Enable full RF power Power for docking cradle detector Handset/LBT switch Signal to mute GPS receiver Enable modem power regulators Enable boost converter Ground Ground Battery Voltage Boost Voltage for PA Battery Voltage Boost Voltage for PA Battery Voltage PCM audio port 1 PCM audio port 1 PCM audio port 1 PCM audio port 1 Power supply Power supply PCM audio port 2 PCM audio port 2 PCM audio port 2 PCM audio port 2 Power supply Power supply DPL port DPL port Data/Fax port Data/Fax port Data/Fax port Data/Fax port Data/Fax port Data/Fax port Data/Fax port Data/Fax port SIM SIM SIM SIM SIM GPIO GPIO GPIO GPIO Power supply Power supply Power supply Power supply Power supply Power supply Power supply Power supply Power supply Iridium Communications, Inc. Proprietary & Confidential Information Page 25 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Table 10: Limits for 3.3V Digital Signals Parameter Symbol Input High Voltage Input Low Voltage Input current Input capacitance Output High Voltage Output Low Voltage Low Level Output Current High Level Output Current VIH VIL IIN CIN VOH VOL IOL IOH Min 2.0
-0.3 2.4 Max Unit 5.5 0.8 20 10 0.4 4.4 5.5 V V A pF V V mA mA 3.2 DC Power Supply Interface 3.2.1 DC Power Supply Inputs The Iridium Core has two DC Power Supply Inputs: VBAT and VBOOST. 3.2.1.1 Battery Power Input, VBAT VBAT is the input from a Lithium-ion battery or other low-voltage source via the user connector. It must be in the range 3.2 to 6V and capable of supplying a maximum current of 500mA. The VBAT supply specification is given in Table 11. Table 11: VBAT Specification Parameter Maximum voltage Minimum voltage Maximum supply current4 Value 6.0V 3.2V 0.5A 3.2.1.2 Boost Power Input, VBOOST VBOOST - Boost converter input via user connector. See Section 3.2.3 for details. The VBOOST supply specification is given in Table 12. The Iridium Core 9523/9523N produces the logic signal PA_BOOST_EN to indicate when the external Boost Power voltage must be applied. This signal can be used as the enable signal to an external boost regulator (logic high = VBOOST needed, logic low = VBOOST not needed). 4 It is recommended that supply overcurrent protection is provided by the partner application that incorporates the Iridium Core 9523/9523N. Iridium Communications, Inc. Proprietary & Confidential Information Page 26 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 3.2.2 Power On/Off Control, TRX_ON The input signal TRX_ON is provided to allow the Iridium Core 9523/9523N to be powered off. This signal controls the power regulators on the Iridium Core 9523/9523N. The Iridium Core 9523/9523N starts up when power is applied and the TRX_ON input is high. As long as the input voltage is applied, logic high on this line turns the Iridium Core 9523/9523N on and a logic low turns it off. If this line is not required then it must be connected directly to the VBAT supply. Prior to turning off the modem, command AT*P0 should be issued to ensure all memory write activity is completed. When the Iridium Core 9523/9523N is powered off, the power-on-reset circuit requires 2 seconds for voltages to decay. Product Developers should therefore not reapply power until this time has elapsed after power has reached 0V. If the 2 second wait time is not adhered to, the reset circuit may not operate and the modem could be placed in a non-operational state. The state is not permanent and can be rectified by the above procedure. Damage may be caused if TRX_ON is high and VBAT is not supplied. Partners must ensure that this condition cannot occur either by generating TRX_ON from VBAT or by adding protection circuitry such as a clamp diode between TRX_ON and VBAT. 3.2.3 Typical Power Usage Profile The amount of current taken by the Iridium Core 9523/9523N on its two supply rails depends on whether it is active in a call and the power step level that the transmitter is using. The current consumption during a call at the highest power step is shown in Figure 8. Figure 8: Current Profile of Supply Rails Iridium Communications, Inc. Proprietary & Confidential Information Page 27 of 34 to Product Developers Only Distribution of Guide Restricted I/mA1002003004005006007008009001000102030405060708090100t/msCurrent in VBOOST RailCurrent in VBAT Rail Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 The current peak in the VBOOST rail lasts for 8.3ms and repeats every 90ms (this is the period of a frame in the Iridium air interface). When not transmitting, the VBOOST current returns to zero. The VBOOST current was measured when the Iridium Core 9523/9523N was connected to a 27V power source that could meet its instantaneous power requirements (around 25W). A block diagram of the VBOOST power supply in a typical Lithium-ion powered application is shown in Figure 9 and Figure 10. Figure 9: Iridium Core 9523 VBOOST block diagram Figure 10: Iridium Core 9523N VBOOST block diagram Iridiums products use a boost-converter circuit based on the Linear Technology LT3580 to produce the VBOOST rail. This circuit is not capable of supplying the instantaneous current needed by the power amplifier. The Iridium Core 9523 therefore includes a total capacitance of 990F on the VBOOST rail to store charge; these capacitors are depleted during the transmit time-slot (8.3ms) and replenished during the remainder of the frame time (81.7ms). The voltage across the capacitors at the end of each transmit time-
slot must not fall below 10.5V; otherwise the output voltage of the buck converter will drop too low and affect the transmitted waveform from the PA; the average current taken from the boost converter in this configuration is around 300mA. The Iridium Core 9523N includes a total capacitance of 1680F on the VBOOST rail to store charge. The voltage across the capacitors at the end of each transmit time-slot must not fall below 16.0V; otherwise the output voltage of the buck-boost converter will drop too low and affect the transmitted waveform from the PA; the average current taken from the boost converter in this configuration is around 300mA. It is possible to produce VBOOST in other ways, particularly if the FA has a convenient supply rail that has high enough voltage and current capacity. Table 12 shows the permissible limits for any VBOOST supply. Iridium Communications, Inc. Proprietary & Confidential Information Page 28 of 34 to Product Developers Only Distribution of Guide Restricted Voice and Data ModemBuck ConverterPower AmplifierLT3580-based Boost Converter3 x 330uF, 35V capacitorsLi-ion3.7VVBOOST27VVoice and Data ModemBuck-Boost ConverterPower AmplifierLT3580-based Boost Converter3 x 560uF, 35V capacitorsLi-ion3.7VVBOOST27V Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Table 12: VBOOST Specification Parameter Absolute maximum voltage
(limited by capacitor rating) Maximum recommended voltage Minimum voltage when capacitors are charged Maximum current into VBOOST pins
(limited by rating of inter-board connector)5 Maximum power taken by buck converter
(during transmit time-slot) Value 35V 32V 27V 1A 30W The maximum average power requirement over a 90ms period is 3.1W. The capacitors discharge to typically 15V on the Iridium Core 9523 and 21V on the Iridium Core 9523N during the transmit burst when operating at maximum power. A typical design would have a power limit of between 5 and 6 Watts
(current approximately 0.25 Amp) so that the reservoir capacitors are replenished in approximately half the allowed time. If the boost voltage at the start of the transmit burst is below the minimum (27V) then the capacitors may discharge to below 9.5V on the Iridium Core 9523 and 16.0V on the Iridium Core 9523N, in which case the transmitter power will reduce. There is a residual VBAT current of about 70mA all the time that the Iridium Core 9523/9523N is switched on, even when not in a call. Periodically, the Iridium Core 9523/9523N will draw about 250mA from the VBAT rail for about 20ms, as it maintains synchronization with the signal from the satellites. When an Iridium call is in progress, there are two peaks in the current drawn by the VBAT rail in each 90ms frame one of about 300mA during the transmit time-slot and a slightly smaller one, 250mA, during the receive time-slot. At the start of each of period when the receiver or transmitter is active a burst of current will be drawn, as the radio circuitry switches on. This current is caused by the charging of six 4.7F capacitors on the outputs of internal voltage regulators6. 3.3 PCM Digital Audio The Iridium Core 9523/9523N has two PCM digital audio ports, though only one of these can be in use at any time. The active port is selected using the AT+CAR command. This setup allows the FA board to provide two parallel audio paths and switch between them through software instead of hardware. The two ports have identical signals and timing, as shown in Figure 11. The PCM clock and sync signals are outputs from the Iridium Core 9523/9523N. The PCM clock signal has a frequency of 2048 kHz with an accuracy of 1 ppm, but it is derived from an internal clock source by a fractional divider so each clock high period and low period is either 238.1 ns or 297.6 ns. The PCM clock, sync and data signal outputs are all timed from the same internal clock and are skewed by less than 1 ns (at equal load). 5 It is recommended that supply overcurrent protection is provided by the partner application that incorporates the Iridium Core 9523/9523N. 6 This is only applicable to the Iridium Core 9523. Iridium Communications, Inc. Proprietary & Confidential Information Page 29 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 The PCM data input has set-up and hold time requirements of 30 ns with respect to the falling edge of the PCM clock signal. The two PCM ports were originally intended to be connected to a voice source/sink via a codec (such as the Texas Instruments TLV320AIC1110) for analog audio and directly for digital audio, but there is no need to use them in this way. PCM clock PCM sync PCM output PCM input Figure 11 - PCM waveform diagram 1 ( msb ) 1 ( msb ) 2 2 3 3 4 4 15 15 16 ( lsb ) 16 ( lsb ) 3.3.1 Port 1 Port 1 has the following signal pins:
Table 13: PCM Port 1 Signals Signal function Signal name PCM clock output CODEC_PCMCLK PCM sync output CODEC_PCMSYNC PCM data output CODEC_PCMIN PCM data input CODEC_PCMOUT Note: the data signal names on Port 1 are defined from the point of view of an externally connected codec. 3.3.2 Port 2 Port 2 has the following signal pins:
Table 14: PCM Port 2 Signals Signal function Signal name PCM clock output UC_DACLK PCM sync output UC_DAFS PCM data output UC_DATX PCM data input UC_DARX Note: the data signal names on Port 2 are defined from the point of view of the Iridium Core 9523/9523N. Iridium Communications, Inc. Proprietary & Confidential Information Page 30 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 3.3.3 11Hz Signal for Manufacturing and Regulatory Testing An external frame tick signal needs to be passed to the Iridium Core 9523/9523N during regulatory radio testing of the host system, and possibly also during manufacturing testing. This frame signal has a period of 90ms (11.1Hz) and is fed to the Iridium Core 9523/9523N using the CODEC_PCMOUT PCM data input. The frame tick signal can have any mark-space ratio but must be externally synchronized to the Iridium Core 9523/9523Ns internal clock. This is most easily achieved by double buffering the signal through two D-type latches clocked by CODEC_PCMCLK. 3.4 DPL port The DPL port is a three-wire asynchronous serial port. It carries 8-bit, no parity data at 115,200 baud. The DPL port enables peripherals such as handsets and SIM card readers to be interfaced to the Iridium Core 9523/9523N. The interface utilizes an Iridium proprietary communication bus not detailed in this document. Details can be made available after appropriate Non-Disclosure and/or License Agreements are executed. The serial data signals use standard 3.3V signals with conventional polarity. If desired, an external RS232 level converter could be fitted to the FA board to extend range. 3.5 Data/Fax port The asynchronous serial data/fax interface is comprised of eight standard RS232 data (8-bit, no parity), control, and status signals plus a ground level signal reference. This interface allows the FA to utilize the Iridium Core 9523/9523Ns modem functionality via AT command control. With respect to this interface, the Iridium Core 9523/9523N behaves as a DCE (Data Communication Equipment), and the FA behaves as a DTE (Data Terminal Equipment). The data/fax interface supports 3.3V / LVTTL levels. If RS-232 voltage levels are needed, the FA must include an LVTTL/RS-232 level shifter. A 3-wire RS232 Data minimal interface may also be implemented; however the 9-wire interface offers better control and is the recommended implementation. Autobaud is enabled by default. Autobaud will occur on the following characters: a, A, or CR (carriage return). Autobaud will also occur on the escape sequence character, provided this is an odd number character. Normally this is set to + in register S2. See the ISU AT Command Reference for further information on the data/fax interface. 3.6 SIM interface The Iridium Core 9523/9523N needs an external Iridium SIM card and socket to be connected to its SIM interface. The signals operate at 3.3V logic levels, so an external SIM level converter such as the ONSemi NCN4555 must be connected between the Iridium Core 9523/9523N and the SIM connector/socket to allow 3V or 1.8V SIM cards to be used. An external SIM card reader may also be interfaced as a peripheral to the Iridium Core 9523/9523N via the DPL interface. A SIM card in the external reader will take precedence over the SIM chip connected to the SIM interface when both are present. Iridium Communications, Inc. Proprietary & Confidential Information Page 31 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 3.7 GPIO Signals There are four GPIO signals to the Iridium Core 9523/9523N, as described in this section. 3.7.1 Transmit power Control The radiated power output from the Iridium transmitter can exceed SAR safety limits if the antenna is too close to the operators body. An Iridium handset has a telescopic antenna to provide the necessary safe distance. The GPIO signals ANT_DET_PWR and FULL_POWER_EN are used to control the transmit power in conjunction with an antenna position-detector switch. The Iridium Core 9523/9523N polls the position-detector switch by providing a 3.3V output on ANT_DET_PWR in order to provide power to the antenna position sensing circuitry. When ANT_DET_PWR is high, the position sensing circuit must take FULL_POWER_EN high to enable full transmit power. 3.7.2 External GPS Receiver Switch If the Iridium Core 9523/9523N is used near a GPS receiver, it is possible that the input circuitry of the GPS receiver could be damaged by the output power of the Iridium transmitter, especially if the two devices share a single antenna. The Iridium Core 9523/9523N has a GPIO signal, TX_ACTIVE, which is high whenever the Iridium transmitter is active and this could be used to control a switch on the input of the GPS receiver. The TX_ACTIVE signal goes high 610us before the start of a transmit burst (ie. full power), and goes low 220us after the end of the burst. There is also 100us of power ramp-up before the burst and 100us of ramp-down after the burst. 3.7.3 Modem/Handset Mode Select Signal A further GPIO signal, LBT_HSTB, is used to indicate whether the Iridium Core 9523/9523N should operate as though it is mounted in a handset or a modem device. It should be pulled to 3.3V for normal modem operation, or 0V for handset mode. The major differences are:
Data/Fax port is operational in modem mode and disabled in handset mode. Background radio scanning for active radio channels is less intensive in handset mode, because power consumption is a more important issue for a battery-powered handset. 4 RF Interface This section describes the physical characteristics of the RF connector and specifications of the RF Interface. 4.1 RF Connector Type The RF connector on the Iridium Core 9523/9523N is an I-PEX part number 20314-001E-01, from their MHF product range. When mating to the Iridium Core 9523/9523N RF connector, use a suitable plug from the MHF (20308) or MHFII (20312) ranges. Iridium Communications, Inc. Proprietary & Confidential Information Page 32 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 Additional information can be found at: http://www.i-pex.com Note that the RF connector on the Iridium Core 9523/9523N is not mounted directly to the FA board along with the user interface connector. It must be attached to the FA board through a coaxial cable. Note that for safety reasons, the RF connector on the Iridium Core 9523/9523N should not be directly connected to an external antenna cable or cable distribution system. Paragraph 7.3 of EN60950-1:2006 safety standard requires that users are protected against high voltages that might appear on these cables. This can be achieved either by inserting a high-voltage isolating capacitor in series with the signal or by grounding the shield of the coaxial cable. The I-PEX connector has limited voltage capacity;
therefore protection needs to be provided on the FA board. Developers are encouraged to review the EN60950-1:2006 standard for additional details. 4.1.1 Antenna Characteristics The Iridium Core 9523/9523N should be connected to a certified Iridium-band antenna with the following antenna connector characteristics as described in Table 15. Table 15: Antenna Characteristics Parameter Impedance Gain (maximum) Polarization VSWR (maximum operational) Value 50 Ohms nominal 3 dBi RHCP 1.5 : 1 Existing qualified Iridium antennas may be used. (i.e. antennas designed and certified for the 9601, 9602, 9522, 9522A and 9522B) in conjunction with suitable protection circuitry. 4.2 RF Interface Specifications The RF interface requirements for the Iridium Core 9523/9523N are summarized in Table 16 below. Table 16: General RF Parameters Parameter Value Frequency Range 1616 MHz to 1626.5 MHz Duplexing Method TDD (Time Domain Duplex) Input/Output Impedance 50 Multiplexing Method TDMA/FDMA Iridium Communications, Inc. Proprietary & Confidential Information Page 33 of 34 to Product Developers Only Distribution of Guide Restricted Iridium Communications, Inc. Information Contained in this Guide Iridium Core 9523/9523N Product Developers Guide is Subject to Change Without Notice Revision 7.2 DRAFT4 4.3 Radio Characteristics Table 17 contains radio characteristics of the Iridium Core 9523/9523N. Table 17: Radio Characteristics Parameter Average Power during a transmit slot (max) Average Power during a frame (typical) Value 7 W 0.6 W Receiver sensitivity (Typical level at connector)
-118 dBm Max Cable loss permitted (Note 1) Link Margin Downlink (Note 2) Link Margin Uplink (Note 2) 3 dB 12 dB 12 dB Note 1: Cable losses should be minimized. The total implementation loss for an antenna, connectors, cable, lightning arrestor and any other RF component between the Iridium Core 9523/9523N and the antenna should not exceed 3 dB. Implementation loss higher than this will affect the Iridium link performance and quality of service. Solutions with a loss higher than 3 dB will not meet the requirements of Iridium Solution Certification. Note 2: Link Margins are given assuming a free-space propagation model. 4.4 S-meter Performance The numbers reported over the AT command interface indicate the signal strength of the ring channel. Care should be taken when using the S-meter readings for comparisons between devices. Of particular note are the following:
1. There is a 0.5 dB tolerance on calibrating the S-meter. 2. Each bar represents a 2 dB increment. 3. Multiple ring channels can be present at the same time so units can lock to different signals. 4. If the reading is near the decision threshold it would be easy to see a 1 bar difference. 5 AT Interface The Iridium Core 9523/9523N is configured and operated through the use of AT commands. See the ISU AT Command Reference for the full set of AT commands and responses. For differences in AT command support between Iridium Core 9523/9523N software releases, see the relevant software release notes, which are made available to authorized Iridium VARs and VAMs on the Iridium Developer Extranet. It is the responsibility of Product Developers to check compatibility of applications software with the AT Commands on all Iridium Core 9523/9523N software versions used for both development and commercial deployments. Iridium Communications, Inc. Proprietary & Confidential Information Page 34 of 34 to Product Developers Only Distribution of Guide Restricted
This product uses the FCC Data API but is not endorsed or certified by the FCC