| submitted | available | document details (if available) | source link |
|---|---|---|---|
| April 06 2001 | October 09 2001 |
| various | Instruction Manual | Users Manual | 686.42 KiB | April 06 2001 / October 09 2001 |
INSTRUCTION MANUAL MULTI-BAND PORTABLE TRANSCEIVER TH-F6A TH-F7E DUAL-BAND PORTABLE TRANSCEIVER KENWOOD CORPORATION B62-XXXX-XX (K) 09 08 07 06 05 04 03 02 01 00 THANK YOU THANK YOU Thank you for choosing this KENWOOD TH-F6A/ TH-
F7E transceiver. It has been developed by a team of engineers determined to continue the tradition of excellence and innovation in KENWOOD transceivers. First, dont let the size fool you. This small FM portable transceiver features 144 MHz, 220 MHz
(TH-F6A only), and 430/ 440 MHz amateur band operation plus another all-mode 100 kHz to 1.2 GHz receiver (SSB and CW are up to less than 600 MHz). In the meantime, as you learn how to use this transceiver, you will also find that KENWOOD is pursuing user friendliness. For example, each time you change the Menu No. in Menu mode, you will see a text message on the display that lets you know what you are configuring. Though user friendly, this transceiver is technically sophisticated and some features may be new to you. Consider this manual to be a personal tutorial from the designers. Allow the manual to guide you through the learning process now, then act as a reference in the coming years. FEATURES Ultra compact design 144 MHz, 220 MHz (TH-F6A only), and 430/ 440 MHz amateur band FM transceiver operation A separate wide band, all-mode receiver, built-in 400 memory channels plus 23 special function memory channels (24 channels for TH-F6A) Long operation period with a Li-ion battery pack High output power (up to 5 W operation) 9600 bps Packet-ready data (Speaker/ Mic.) jack Built-in VOX function SUPPLIED ACCESSORIES After carefully unpacking the transceiver, identify the items listed in the table below. We recommend you keep the box and packing material in case you need to repack the transceiver in the future. yrosseccA rebmuNtraP koohtleB annetnA partS yrettabnoi-iL regrahC noitcurtsnI launaM ecitoNETT&R dracytnarraW XX-3260-92J XX-1870-09T
)dnab-4(
XX-9870-09T
)dnab-3(
XX-9330-96J XX-9790-90W XX-7290-80W XX-8290-80W XX-9290-80W XX-1441-26B
)S/E(
XX-2441-26B
)I/F(
XX-3441-26B
)G/D(
XX-7622-95B XX-9640-64B XX-0130-64B ytitnauQ A6F-HT
)K(
E7F-HT
)E(
)T(
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 WRITING CONVENTIONS FOLLOWED The writing conventions described below have been followed to simplify instructions and avoid unnecessary repetition. noitcurtsnI sserP
]YEK[
]YEK[
]YEK[
]YEK[
]YEK[
. sserP
]2YEK[+]1YEK[
]2YEK[+]1YEK[
]2YEK[+]1YEK[
]2YEK[+]1YEK[
]2YEK[+]1YEK[
. sserP
]1YEK[
]1YEK[
]1YEK[
]1YEK[
]1YEK[
,
]2YEK[
]2YEK[
]2YEK[
]2YEK[
]2YEK[
. sserP
[+]YEK[
[+]YEK[
[+]YEK[
[+]YEK[
[+]YEK[
]
]
]
]
]
. oDottahW YEK YEK YEK YEK YEK .
,nwod 1YEK 1YEK 1YEK 1YEK 1YEK 2YEK 2YEK 2YEK 2YEK 2YEK
. esaelerdnasserP dlohdnasserP eraerehtfI sserpneht dnasserp,syekowtnahterom litnunrutniyekhcaenwoddloh
.desserpneebsahyeklanifeht sserP 2YEK 2YEK 2YEK 2YEK 2YEK esaeler
.
,FFOrewopreviecsnartehthtiW dlohdnasserp hctiwsneht, ybrewopreviecsnartehtNO gnisserp
,yliratnemom sserpneht,
.)REWOP(
1YEK 1YEK 1YEK 1YEK 1YEK 1YEK 1YEK 1YEK 1YEK 1YEK YEK YEK YEK YEK YEK
]
]
]
]
]
[
[
[
[
[
i NOTICE TO THE USER One or more of the following statements may be applicable for this equipment. FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer for technical assistance. MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual. TH-F6A:
144 MHz/ 220 MHz/ 440 MHz FM Multi-band Portable Transceiver 144 MHz/ 430 MHz FM Dual-band Portable Transceiver TH-F7E:
The Americas Europe/ Universal type United Kingdom MARKET CODES K-type:
E-type:
T-type:
The market code is shown on the carton box. Refer to the specifications {page xx} for the information on available operating frequencies within each market. ii PREPARATION INSTALLING THE Li-ion BATTERY PACK Note: Because the battery pack is provided uncharged, you must charge the battery pack before using it with the transceiver. To charge the battery pack, refer to CHARGING THE Li-ion BATTERY PACK {page 2}. 1 Position the two grooves on the edge and two hooks at the bottom of the battery pack over the corresponding guides on the back of the transceiver. Grooves 2 Slide the battery pack along the back of the transceiver until the release latch on the top of the transceiver locks the battery pack in place. 3 To remove the battery pack, pull the release latch on top, then slide the battery pack down. Latch INSTALLING ALKALINE BATTERIES 1 To open the battery case (BT-13), push the locking tab in, then pull the cover back. Tab 2 Insert (or remove) four AA (LR6) alkaline batteries. Be sure to match the battery polarities with those marked in the bottom of the battery case. 3 Align the two tabs on the battery case cover, then close the cover until the locking tabs click. Tabs 4 To install the battery case onto (or remove it from) the transceiver, follow steps 1 to 3 of INSTALLING THE Li-ion BATTERY PACK
{above}. INSTALLING THE ANTENNA Hold the base of the supplied antenna, then screw the antenna into the connector on the top panel of the transceiver until secure. a ATTACHING THE HAND STRAP If desired, you can attach the supplied hand strap to the transceiver. Strap INSTALLING THE BELT CLIP You can install the supplied belt clip to the transceiver tightening the 2 supplied screws. Screws 1 1 PREPARATION CHARGING THE Li-ion BATTERY PACK The Li-ion battery pack can be charged after it has been installed onto the transceiver. The battery pack is provided uncharged for safety purposes. 1 Confirm that the transceiver power is OFF. While charging the battery pack, leave the transceiver power OFF. 2 Insert the charger plug into the DC IN jack of the transceiver. DC IN jack CONNECTING TO A REGULATED POWER SUPPLY To connect the transceiver to an appropriate regulated power supply, use an optional PG-2W DC cable. 1 Confirm that the power of both the transceiver and the power supply are OFF. 2 Connect the optional PG-2W DC cable to the power supply; the red lead to the positive (+) terminal, and the black lead to the negative () terminal. 3 Plug the charger into an AC wall outlet. Charging starts and CHARGING appears. 4 It takes approximately 6 hours to charge an empty PB-42L Li-ion battery. When charging is complete, STANDBY appears; remove the charger plug from the transceiver DC IN jack. 5 Unplug the charger from the AC wall outlet. Fuses 3 Connect the barrel plug on the DC cable to the DC IN jack of the transceiver. DC IN jack Note:
u Only use power supplies recommended by your authorized KENWOOD dealer. u The supply voltage must be between 5.5 V and 16 V to prevent damaging the transceiver. If input voltage exceeds approximately 18 V, warning beeps sound and VOLTAGE ERROR appears. u Exceeding the specified charge period shortens the useful life of the Li-ion battery pack. u The provided charger is designed to charge only the provided PB-42L Li-ion battery pack. Charging other models of battery packs may damage the charger and battery pack. CONNECTING TO A CIGARETTE LIGHTER SOCKET To connect the transceiver to the cigarette lighter socket in your vehicle, use an optional PG-3J Cigarette Lighter cable. DC IN jack DC 12 V To connect with an external 24 V power source via a DC-DC converter, only use the optional PG-3J Cigarette Lighter cable. Using the PG-2W DC cable in this situation may cause a fire. 24V 24V 24V DC-DC Converter 12V Socket 12V PG-3J PG-3J DC-DC Converter 12V PG-2W Note: If the input voltage exceeds approximately 18 V, warning beeps sound and VOLTAGE ERROR appears. 2 YOUR FIRST QSO FIRST QSO Are you ready to give your TH-F6A/ TH-F7E a quick try? Reading this page should get your voice on the air right away. The instructions below are intended only for a quick guide. If you encounter problems or there is something you would like to know more, read the detailed explanations given later in this manual. 6 7 8 3 5 4 1 2 r Press [BAND] until you select the amateur radio band you wish to operate. t Turn the Tuning control to select the receive frequency. You may further turn the VOL control to adjust the volume level of the signal. y To transmit, hold the transceiver approximately 5 cm (2 inches) from your mouth. u Press and hold the PTT switch, then speak in your normal tone of voice. i Release the PTT switch to receive. o Repeat steps y, u and i to continue communication. q Presss and hold [
] (POWER) briefly to switch the transceiver power ON. Do not press the switch for more than approximately 2 seconds; the transceiver will be switched OFF. A high pitched double beep sounds and then KENWOOD and HELLO!! appears momentarily. The various indicators and 2 frequencies appear on the LCD. w Press [A/B] to select the frequency band on top. Each time you press [A/B], the s icon moves, indicating which frequency band is currently selected for operation. e Turn the VOL control clockwise to the 11 oclock position. 3 GETTING ACQUAINTED KEYS AND CONTROLS Antenna Tuning Control VOL Control Display SP/MIC jack Speaker/ Mic. DC IN jack Keypad PTT switch LAMP Key Menu/Cursor Keys MONI Key Power Switch M A/ B-band status LEDs 4 DISPLAY 4 GETTING ACQUAINTED 1 2 3 4 5 6 7 8 9 10 11 12 13 14 22 21 15 16 17 18 19 20 q E L Appears when the transmit output power is set to Low
(L) or Economic Low (E L) {pages 7, }. w H Appears when the transmit output power is set to High (H) {pages 7, }. e LSB Appears when lower side band (LSB) is selected for B-band {page 36}. r USB Appears when upper side band (USB) is selected for B-band {page 36}. t CW Appears when CW is selected for B-band {page 36}. y WFM/ FM/ FMN WFM appears when wide FM mode is selected
{page 36}. FM appears when normal FM mode is selected. FMN appears when narrow FM mode is selected
{pages 36, }. u AM AM appears when AM mode is selected {page 36}. i Appears when a priority scan is activated {page 25}. o FINE Appears when a fine tuning function is activated.
!0 VOX Appears when the VOX function is activated
{page xx}.
!1 Appears when the Automatic Simplex Check (ASC) is activated {page 14}.
!2 Appears when the Key lock function is activated
{page xx}.
!3 Appears when the function key is pressed.
!4 S-meter (RX) and relative output power meter (TX).
!5 CT CT appears when the CTCSS function is activated
{page 28}.
!6 Appears when the Tone function is activated
{page 13}.
!7 DCS Appears when the DCS function is activated
{page 29}.
!8 +/ /
Appears when the repeater shift function is activated
{page 12}.
!9 R Appears when the Reverse shift function is activated
{page 14}.
@0 Appears when the Tone Alert function is activated
{page xx}.
@1 Appears when the displayed memery channel has been locked out {page 27}.
@2 Full dot-matrix display (76 x 16 dots). It displays various informations, such as the operating frequencies, menu settings, and etc. 5 4 GETTING ACQUAINTED BASIC OPERATION SWITCHING POWER ON/ OFF 1 Press [
] (POWER) briefly to switch the transceiver power ON. Do not press the key for more than approximately 2 seconds; the transceiver will be switched OFF. Upon power up, a high pitched double beep sounds, followed by the frequencies and other indicators. 2 To switch the transceiver OFF, press [
]
(POWER) again. When you turn the transceiver OFF, a low pitched double beep sounds. ADJUSTING VOLUME Turn the VOL control clockwise to increase the audio output level and counterclockwise to decrease the output level. If you are not receiving a signal, press and hold
[MONI] to unmute the speaker, then adjust the VOL control to a comfortable audio output level. ADJUSTING SQUELCH The purpose of the Squelch is to mute the speaker when no signals are present. With the squelch level correctly set, you will hear sound only while actually receiving signals. The higher the selected squelch level, the stronger the signals must be, to receive. The appropriate squelch level depends on the ambient RF noise conditions. You can configure independent threshold squelch levels for the A-band and B-band. 1 Press [SQL]. The current SQL level appears. 2 Turn the Tuning control or press [
]/ [
] to adjust the level. Select the level at which the background noise is just eliminated when no signal is present. 6 The higher the level, the stronger the signals must be, to receive. 6 different levels can be set (OPEN: unmuted ~
|| || || || || || : maximum). 3 Press [sssss] or [MNU] to store the new settings or press [ttttt] to cancel without changing the current setting. SELECTING A BAND By default, two frequencies are displayed on the LCD. The frequency on top is called the A-band. The bottom frequency is called the B-band. A-band B-band Press [A/B] to select the A-band or B-band for operation. Each time you press [A/B], the s icon moves, indicating which band is currently selected for operation. Usually, select the A-band to operate the amateur band and select the B-band to receive the various broadcasting stations, such as AM, FM, TV
(audio only) or another amateur band {page 35}. CURSOR KEYS This transceiver has a 4-way cursor key with a MENU
(MNU) key in the center.
/
keys
/
keys function in the same way as the The Tuning control. These keys change the frequencies, memory channels, and other selections. Note: You can use the Tuning control in place of the / keys for most of the controls. s/ OK key Press to move to the next step or complete the setting in various modes, such as Menu mode, CTCSS frequency selection, and DCS code selection. t/ ESC key Press to move back or cancel the entry in various modes, such as Menu mode, CTCSS frequency selection, and direct frequency entry. MNU key Press to enter the Menu mode. In Menu mode, you can select the desired menu number by turning the Tuning control or pressing
[
]/ [
]. TRANSMITTING 1 To transmit, hold the transceiver approximately 5 cm (2 inches) from your mouth, then press and hold the PTT switch and speak into the microphone in your normal tone of voice. The status LED on the top panel lights red and bar-graph meter appears. If you press [PTT] while you are outside of the transmission coverage, a high pitched error beep sounds. 4 GETTING ACQUAINTED 1 Press [MHz]. A MHz digit blinks. 2 Turn the Tuning control or press [
the desired MHz digit.
]/[
] to select 3 After selecting the desired MHz digit, press [MHz]
to exit the mode and return to normal tuning mode. 4 You may further adjust the frequency using the Tuning control or [
]/[
]. 2 When you finish speaking, release the PTT switch. Note: If you transmit countinuously for more than 10 mintues, the internal time-out timer generates a warning beep and the transceiver stops transmitting. In this case, release the PTT switch and let the transceiver cool down for a while, then press the PTT switch again to resume transmitting {page xx}. n Selecting Output Power Selecting lower transmission power is the best way to reduce the battery consumption, if communication is still reliable. You can configure different power levels for transmission {page xx}. Press [LOW]. Each time you press [LOW], the indicator cycles between H (high), L (low), and EL (economic low). Note:
u You can store different output power setting for the A and B-band. When you change the output power, it is reflected to all available amateur bands for A or B-band. SELECTING A FREQUENCY n VFO mode This is the basic mode for changing the operating frequency. Turn the Tuning control clockwise to increase the frequency. Turn the Tuning control counterclockwise to decrease the frequency. Or, press [
] to change the frequency.
]/ [
If the desired operating frequency is far away from the current frequency, it is quicker to use the MHz tuning mode. n Direct Frequency Entry In addition to turn the Tuning control or press [
there is another way of selecting the frequency. When the desired frequency is far away from the current frequency, you can directly enter a frequency from the numeric keypad. 1 Press [VFO].
]/[
], You must be VFO mode to make the direct frequency entry. 2 Press [ENT]. appears. 3 Press the numeric keys ([0] to [9]) to enter your desired frequency. [MHz] can be used to complete the MHz digits entry. Pressing [ENT] fills the remaining digits (the digits you did not enter) with 0 and completes the entry. To select 145.000 MHz for example, press [1],
[4], [5] then press [ENT] to complete the entry. Example 1 (100 MHz < f < 1000 MHz) To enter 438.320 MHz:
Key in
[ENT]
[4], [3], [8]
[3], [2], [0]
Display 4 3 8. 4 3 8. 3 2 0 Note: You do not have to press [MHz] when you are entering 3-
digit MHz number. 7 4 GETTING ACQUAINTED Example 2 To enter 439.000 MHz:
Key in
[ENT]
[4], [3], [9]
[ENT]
Display 4 3 9. 4 3 9. 0 0 0 Example 3 ( f > 1000 MHz) To enter 1250.500 MHz (B-band only):
Key in
[ENT]
[1], [2], [5], [0]
[5]
[ENT]
Display 12 5 0. 12 5 0. 5 12 5 0. 5 0 0 Example 4 (f < 100 MHz) To enter 10.500 MHz (B-band only):
Key in
[ENT]
[1], [0]
[MHz]
[5]
[ENT]
Display 1 0 1 0. 1 0. 5 1 0. 5 0 0 0 Note: When pressing the last [ENT], the FINE tuning function is automatically activated for 10.5000 MHz. Example 5 To enter 810 kHz (B-band only):
Key in
[ENT]
[0]
[MHz]
[8], [1], [0]
Display 0 0. 0. 8 1 0 Note:
u If the entered frequency does not match the current frequency step size, the frequency is automatically rounded up or down to the next available frequency. u When the desired frequency cannot be entered exactly, check whether the FINE function is ON or not and confirm the frequency step size {page xx}. u Some frequency ranges are blocked, due to government regulations. Refer to the specifications for the TX/ RX coverage. u If you turn the Tuning control or press [ ]/ [ ] while entering the frequency, the transceiver clears the entry and recovers the previous frequency and mode. 8 MENU SETUP WHAT IS A MENU?
Many functions on this transceiver are selected or configured via a software-controlled Menu, rather than through the physical controls of the transceiver. Once familiar with the Menu system, you will appreciate the versatility it offers. You can customize the various timings, settings, and programming functions on this transceiver to meet your needs without using many controls and switches. MENU ACCESS 1 Press [MNU]. The Menu No. and setting appear on the display, along with a brief explanation of the Menu No. 2 Turn the Tuning control or press [
]/ [
] to select your desired Menu No. As you change the Menu No., a brief explanation of each Menu No. appears. SELECTING A MENU LANGUAGE You can select either English or Japanese (katakana) for the menu description. To switch the language:
1 Press [MNU]. 2 Turn the Tuning control or press [
]/ [
] to select Menu No. 27. 3 Turn the Tuning control or press [
either ENGLISH or JAPANESE.
]/ [
] to select 4 Press [sssss] or [MNU] to store the setting. Otherwise, press [ttttt] or [PTT] to cancel. When you select JAPANESE in step 3 and press [sssss] or [MNU], all Menu explanations are displayed in Japanese (katakana). To return to English mode, repeat step 1 and 2 {above} to access Menu No. 27, then select EIGO. Press [sssss] or [MNU] to display the Menu mode in English. 3 Press [sssss] or [MNU] to configure the parameter of the currently selected Menu No. 4 Turn the Tuning control or press [
your desired parameter.
]/ [
] to select 5 Press [sssss] or [MNU] to store the setting. Otherwise, press [ttttt] or [PTT] to cancel. Note: The menu language selection does not affect any other modes, such as memory name or DTMF name. MENU FUNCTION LIST yalpsiDehtnO uneM
.oN noitcnuF snoitceleS tluafeD
.feR gaP e EMUSERNACS KNILPRG.M DOHTEMRM OFVGORP TESFFOOTUA TESFFO ELBANEENUT TIBIHNIXT KCAJPS/CIM 1 2 3 4 5 6 7 8 9 dohtememusernacS edomdetarepO-emiT:EMIT edomdetarepO-reirraC:REIRRAC edompotsdnakeeS:KEES noitarugifnockniLpuorGyromeM noitidnocllaceRyromeM
/REIRRAC/EMIT KEES EMIT 72 76543210 skniLoN
/SDNABLLA LLA DNABTNERRUC SDNAB egnarycneuqerfOFVelbammargorP eeS ecnerefeR egaP noitcnuftesffOretaepeRotuA FFO/NO NO ycneuqerftesfforetaepeR syekehtnehwlortnocgninuTehtfoesutimreP dekcolera noissimsnartehttibihnI zHM59.95~00.0 fospetsni zHM50.0 FFO/NO FFO/NO eeS ecnerefeR egaP FFO FFO noitcnufkcajPS/CIMehttceleS CP/CNT/PS/CIM PS/CIM 42 61 31 21 9 6 MENU SETUP yalpsiDehtnO uneM
.oN noitcnuF snoitceleS tluafeD
.feR gaP e EROTSFMTD 01 seiromemFMTDnisrebmunFMTDerotS ataDoN 13 23 13 DPSFMTD 11 deepsnoissimsnartenotFMTD WOLS/TSAF TSAF DLOHFMTD ESUAPFMTD 21 31 neewtebsdnoces2rofnoissimsnartehtdloH seirtneyekFMTD FFO/NO FFO FMTDgnittimsnartelihwnoitarudesuapehT senot
/005/052/001
/0051/0001/057 sm0002 sm005 23 KCOLFMTD 41 syekhtiwnoissimsnartFMTDelbasiD FFO/NO FFO 33 GSMNO-RWP 51 egassemno-rewoP sretcarahc8
!!OLLEH TSARTNOC 61 tsartnocyalpsidDCL mumixam:61~muminim:1 REVASTAB 71 doirepffo-tuhsreviecerrevasyrettaB 61~1 8 04
/6.0/4.0/2.0/FFO
/0.3/0.2/0.1/8.0
.ces0.5/0.4
.ces0.1 OPA 81 noitcnufffOrewoPcitamotuA
.nim06/03/FFO
.nim03 04 PEEBYEK 91 noitcnufpeeB FFO/NO NO 04 YSUBnoXOV NIAGXOV 02 12 sireviecerehtnehwnoissimsnartXOVwollA ysub ytivitisnesniagXOVehtteS evitisnestsom:9~evisitnestsael:0 FFO/NO FFO 9~0 4 YALEDXOV 22 emityaledXOVehttsujdA
/003/002/001
/0051/0001/005 sm0003 YEKLLAC 32 yekLLACehtrofnoitcnufatceleS zH0571/LLAC DLOH0571 TFIHSTAEB TNARAB 42 52 62 sienotzH0571anehwsutatsXTehtdloH dettimsnart ycneuqerfkcolcUPClanretniehttfihS zHM0.7wolebannetnarablanretninaelbanE EGAUGNAL 72 egaugnalunemehttceleS FFO/NO FFO/NO
/ELBANE ELBASID
/HSILGNE ESENAPAJ sm005 LLAC
)A6F-HT(
zH0571
)E7F-HT(
FFO FFO ELBANE HSILGNE 91 31 04 04 9 TEKCAP WORRANMF 82 92 noitarepodnabworranMF deepstekcapCNTlanretxenatceleS spb0069/0021 spb0021 FFO/NO
/TESEROFV/ON
/TESERUNEM TESERLLUF FFO ON
?TESER 03 edomteseratceleS 10 ALPHABETICAL FUNCTION LIST yalpsiDehtnO
.oNuneM snoitceleS tluafeD gaP.feR e 6 MENU SETUP OPA TESFFOOTUA TNARAB REVASTAB TFIHSTAEB YEKLLAC TSARTNOC DLOHFMTD KCOLFMTD ESUAPFMTD DPSFMTD EROTSFMTD WORRANMF PEEBYEK EGAUGNAL KCAJPS/CIM DOHTEMRM KNILPRG.M TESFFO TEKCAP OFVGORP GSMNO-RWP
?TESER EMUSERNACS ELBANEENUT TIBIHNIXT YALEDXOV NIAGXOV YSUBnoXOV DLOH0571 81 5 62 71 52 32 61 21 41 31 11 01 92 91 72 9 3 2 6 82 4 51 03 1 7 8 22 12 02 42 setunim06/03/FFO NO/FFO ELBASID/ELBANE
.nim03 NO ELBANE sdnoces0.5/0.4/0.3/0.2/0.1/8.0/6.0/4.0/2.0/FFO
.ces0.1 NO/FFO zH0571/LLAC 61~1 NO/FFO NO/FFO sm0002/0051/0001/057/005/052/001 WOLS/TSAF NO/FFO NO/FFO ESENAPAJ/HSILGNE CP/CNT/CIM/PS DNABTNERRUC/SDNABLLA 76543210 zHM50.0fospetsnizHM59.95~00.0 spb0069/0021 egarevocreviecermumixaM sretcarahcciremun-ahpla8 TESERLLUF/TESERUNEM/TESEROFV/ON KEES/REIRRAC/EMIT NO/FFO NO/FFO FFO LLAC
/)E7F-HT(
zH0571
)A6F-HT(
8 FFO FFO sm005 TSAF atadoN FFO NO HSILGNE CIM/PS LLA SDNAB kniLoN
/zHM06.0 zHM6.1
)A6F-HT(
spb0021
!!OLLEH ON EMIT FFO FFO sm0003/0051/0001/005/003/002/001 sm005 9~0 NO/FFO NO/FFO 4 FFO FFO 04 11 OPERATING THROUGH REPEATERS Repeaters, which are often installed and maintained by radio clubs, are usually located on mountain tops or other elevated locations. Generally they operate at higher ERP (Effective Radiated Power) than a typical station. This combination of elevation and high ERP allows communications over much greater distances than communications without using repeaters. Most repeaters use a receive and transmit frequency pair with a standard or non-standard offset (odd-split). In addition, some repeaters must receive a tone from the transceiver to allow it to access. For details, consult your local repeater reference. PROGRAMMING OFFSET First select an amateur radio repeater downlink frequency on the A-band or B-band as described in SELECTING A FREQUENCY {page 7}. n Selecting Offset Direction Select whether the transmit frequency will be higher (+) or lower () than the receive frequency. Press [F], [REV] to select the offset direction.
+ or appears, indicating which offset direction is selected. TX: 144.725 MHz TX tone: 88.5 Hz RX: 145.325 MHz TX: 144.725 MHz TX tone: 88.5 Hz RX: 145.325 MHz Offset Programming Flow q Select a band. w Select a receive frequency. e Select an offset direction. r Select an offset frequency.
(Only when programming odd-split repeater frequencies) t Activate the Tone function.
(If necessary) y Select a tone frequency.
(If necessary) If you store the above data in a memory channel, you need not reprogram every time. See MEMORY CHANNELS {page 15}. 12 To program 7.6 MHz offset on the TH-F7E
(430 MHz only), repeatedly press [F], [REV]
until appears. If the offset transmit frequency falls outside the allowable range, transmitting is inhibited. Use one of the following methods to bring the transmit frequency within the band limits:
Move the receive frequency further inside the band. Note: While using an odd-split memory channel or transmitting, you cannot change the offset direction. n Selecting Offset Frequency To access a repeater which requires an odd-split frequency pair, change the offset frequency from the default which is used by most repeaters. The default offset frequency on the 144 MHz band is 600 kHz (All models); the default on the 430/ 440 MHz band is 5 MHz (TH-F6A) or 1.6 MHz
(TH-F7E); the default on the 220 MHz band is 1.6 MHz (TH-F6A). 1 Press [BAND] to select an amateur radio band you want to change the offset frequency. 2 Press [MNU]. 3 Turn the Tuning control or press [
select Menu No. 6 (OFFSET).
]/[
] to 4 Press [sssss] or [MNU]. 5 Turn the Tuning control or press [
]/ [
select the appropriate offset frequency. The selectable range is from 0.00 MHz to
] to 59.95 MHz in steps of 50 kHz. 6 Press [sssss] or [MNU] to store the setting. TH-F7E Only: If you have selected for the offset direction, you cannot change the default (7.6 MHz) offset frequency. Note: After changing the offset frequency, the new offset frequency will also be used by Automatic Repeater Offset. n Activating Tone Function Press [TONE] to switch the Tone function ON (or OFF). T appears when the Tone function is ON. Note: You cannot use the Tone and CTCSS/ DCS functions at the same time. Switching the Tone function ON after activating the CTCSS deactivates the CTCSS/ DCS function. TH-F7E Only: When you access repeaters that require 1750 Hz tones, you need not activate the Tone function. Press [CALL]
without pressing the PTT switch to transmit a 1750 Hz tone
(default setting). n Selecting a Tone Frequency 1 While the Tone function is ON, press [F],
[TONE]. 2 Turn the Tuning control or press [
select the desired tone frequency.
]/ [
] to 3 Press [sssss] or [MNU] to complete the setting. 5 OPERATING THROUGH REPEATERS AUTOMATIC REPEATER OFFSET This function automatically selects an offset direction, according to the frequency that you select on the 144 MHz and 220 MHz (TH-F6A only) bands. The transceiver is programmed for offset direction as shown below. To obtain an up-to-date band plan for repeater offset direction, contact your national Amateur Radio association. TH-F6A (U.S.A. and Canada) This complies with the standard ARRL band plan. 144.0 145.5 146.4 147.0 147.6 145.1 146.0 146.6 147.4 148.0 MHz S S
+
S
+
S S: Simplex TH-F7E (Europe/ Others) 144.0 145.6 145.8 146.0 MHz S S S: Simplex Note: Automatic Repeater Offset does not function when Reverse is ON. However, pressing [REV] after Automatic Repeater Offset has selected an offset (split) status, exchanges the receive and transmit frequencies. 1 Press [MNU]. 2 Turn the Tuning control or press [
Menu No. 5 (AUTO OFFSET).
]/ [
] to select
.oN
.oN Available Tone frequencies
.qerF
)zH(
4.79 0.001 5.301 2.701 9.011 8.411 8.811 0.321 3.721 8.131 5.631
.qerF
)zH(
0.76 3.96 9.17 4.47 0.77 7.97 5.28 4.58 5.88 5.19 8.49 10 20 30 40 50 60 70 80 90 01 11 21 31 41 51 61 71 81 91 02 12 22
.oN 43 53 63 73 83 93 04 14 24
.qerF
)zH(
5.602 7.012 1.812 7.522 1.922 6.332 8.142 3.052 1.452
.oN 32 42 52 62 72 82 92 03 13 23 33
.qerF
)zH(
3.141 2.641 4.151 7.651 2.261 9.761 8.371 9.971 2.681 8.291 5.302 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
the function ON or OFF.
]/ [
] switch 5 Press [sssss] or [MNU] to store the setting. Note: 42 different tones are available for TH-F6A/ TH-F7E. These 42 tones includes 37 EIA standard tones and 5 non-
standard tones. TH-F7E only:
u To transmit a 1750 Hz tone, simply press [CALL] without pressing the PTT switch (default setting). Release [CALL] to quit transmitting. You can also make the transceiver remain in the transmit mode for 2 seconds after releasing [CALL]; a 1750 Hz tone is not continuously transmitted. Access Menu No. 24 (1750 HOLD) and select ON. u If you desire to assign [CALL] for recalling the Call channel in place of transmitting the 1750 Hz tone, access Menu No. 23 (CALL KEY) and select CALL. 13 TONE FREQ. ID SCAN This function scans through all tone frequencies to identify the incoming tone frequency on a received signal. You may use the function to find which tone frequency is required by accessing your local repeater. 1 While the Tone function is ON, press [F], [TONE]
(1 s) to start the Tone Freq. ID scan. When the transceiver receives the signal, the scan starts. To reverse the scan direction, turn the Tuning control or press [
]/ [
]. To quit the function, press [PTT] or [ttttt]. When the tone frequency is identified, a beep sounds and the identified frequency appears. 2 Press [sssss] to program the identified frequency in place of the current tone frequency. Press [ttttt] if you do not want to program the identified frequency. Press [
]/ [
] while the identified frequency is blinking, to resume scanning. Note: Some repeaters do not re-transmit the access tone in the downlink signal. In this case, check the other stations uplink signal to detect the repeater access tone. 5 OPERATING THROUGH REPEATERS REVERSE FUNCTION The reverse function exchanges a separate receive and transmit frequency. So, while using a repeater, you can manually check the strength of a signal that you receive directly from the other station. If the stations signal is strong, both stations should move to a simplex frequency and free up the repeater. 144.725 MHz 1 4 5
. 3 2 5 M H z 144.725 MHz TX: 144.725 MHz TX: 144.725 MHz TX: 144.725 MHz TX: 145.325 MHz RX: 145.325 MHz RX: 145.325 MHz RX: 145.325 MHz RX: 144.725 MHz To swap the transmit and receive frequencies:
Press [REV] to switch the Reverse function ON (or OFF). R appears when the function is ON. AUTOMATIC SIMPLEX CHECK (ASC) While using a repeater, the ASC function periodically checks the strength of a signal that you are receiving directly from the other station. If the stations signal is strong enough to allow direct contact without a repeater, R indicator on the display starts blinking. Press [REV] (1 s) to switch the function ON. R appears when the function is ON. While direct contact is possible, R icon blinks. To quit the function, press [REV] momentarily. Note:
u Pressing the PTT switch causes R icon to quit blinking. u ASC does not function if your transmit and receive frequencies are the same (simplex operation). u ASC does not function while scanning. u Activating ASC while using Reverse switches Reverse OFF. u If you recall a memory channel or the Call channel that contains a Reverse ON status, ASC is switched OFF. u ASC causes received audio to be momentarily intermitted every 3 seconds. 14 MEMORY CHANNELS In memory channels, you can store frequencies and related data that you often use. Then you need not reprogram those data every time. You can quickly recall a programmed channel through simple operation. A total of 400 memory channels are available for storing the frequencies, modes and other operating conditions of the A and B-bands. SIMPLEX & REPEATER OR ODD-SPLIT MEMORY CHANNEL?
You can use each memory channel as a simplex &
repeater channel or an odd-split channel. Store only one frequency to use as a simplex & repeater channel or two separate frequencies to use as an odd-split channel. Select either application for each channel depending on the operations you have in mind. Simplex & repeater channels allow:
Simplex frequency operation Repeater operation with a standard offset
(if an offset direction is stored) Odd-split channels allow:
Repeater operation with a non-standard offset Note: Not only can you store data in memory channels, but you can also overwrite existing data with new data. The data listed below can be stored in each memory channel:
retemaraP
&xelpmiS retaepeR tilps-ddO seY ycneuqerfevieceR ycneuqerftimsnarT ycneuqerfenoT NOenoT ycneuqerfSSCTC NOSSCTC edocSCD NOSCD noitceridtesffO ycneuqerftesffO NOesreveR ezispetsycneuqerF tuokcollennahcyromeM emanlennahcyromeM NOgninutENIF noitcelesedoM Yes: Can be stored in memory. N/A: Cannot be stored in memory. seY seY seY seY seY seY seY seY seY seY seY seY seY seY seY seY seY seY seY seY seY seY A/N A/N A/N seY seY seY seY seY STORING SIMPLEX FREQUENCIES OR STANDARD REPEATER FREQUENCIES 1 Press [VFO]. 2 Turn the Tuning control or press [
]/ [
your desired frequency in the amateur radio bands. You can also directly enter desired frequency using the keypad {page 7}.
] to select 4 If storing a standard repeater frequency, select the following data:
Offset direction {page 12}
Tone function, if necessary {page 13}
CTCSS/ DCS function, if necessary
{pages 28, 29}
If storing a simplex frequency, you may select other related data (CTCSS or DCS settings, etc.). 5 Press [F]. A memory channel number appears and blinks. indicates the current channel is empty;
appears if the channel contains data. Memory channel number L0/ U0 ~ L9/ L9
{page 23}, I-0 ~ I-9 {page 20}, and Pr1 and Pr2 {page 25} are reserved for other functions. Do not use these memories to store the TX/ RX data. 6 Turn the Tuning control or press [
]/ [
] to select the memory channel in which you want to store the data. 7 Press [MR] to store the data to the channel. STORING ODD-SPLIT REPEATER FREQUENCIES Some repeaters use a receive and transmit frequency pair with a non-standard offset. If you store two separate frequencies in a memory channel, you can operate on those repeaters without programming the offset frequency and direction. 1 Store the desired receive frequency and related data by following the procedure given for simplex or standard repeater frequencies, above. 2 Turn the Tuning control or press [
the desired transmit frequency.
]/ [
] to select 3 Press [F], [MR]. 4 Turn the Tuning control or press [
]/ [
] to select the memory channel you programmed in step 1. 5 Press [PTT]+[MR]. The transmit frequency is stored in the memory channel. Note: When you recall an odd-split memory channel, + and appear on the display. To confirm the transmit frequency, press
[REV]. 15 8 MEMORY CHANNELS RECALLING A MEMORY CHANNEL There are 2 ways of recalling the desired memory channel. n Using the Tuning control or 1 Press [MR] to enter Memory Recall mode. keys
/
The memory channel used last is recalled. 4 Press [MR] to erase the channel data. The contents of the memory channel are erased. To quit clearing the memory channel, press any key other than [MR]. Note:
u If you clear the information channel data, the data will be set to the factory default values. u You can also clear the Priority channel data, and L0/U0 ~ L9/U9 data. MEMORY RECALL MODE Since the transceiver has more than 400 memory channels, it sometimes takes time to search for your desired memory channel. By default, the transceiver can recall all memory channels when [MR] is pressed, regardless of the current operating band. However, you can configure the transceiver to recall only the memory channels that have the same band information. For example, when you operate on the 144 MHz band in VFO mode, pressing [MR] recalls only the memory channels that have 144 MHz band information. To change the memory recall mode:
1 Press [MNU]. 2 Turn the Tuning control or press [
] to select
]/ [
Menu No. 3 (MR METHOD). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
CURRENT BAND.
]/ [
] to select 5 Press [sssss] or [MNU] to store the setting. When you press [MR] in VFO mode, only memory channels that have the same band data are recalled. To return to the default memory recall mode, repeat step 1 to 5 {above} and select ALL BANDS in step 4. 2 Turn the Tuning control or press [
]/ [
] to select your desired memory channel. You cannot recall an empty memory channel. To restore VFO mode, press [VFO]. Note: If the CURRENT BAND is selected for Menu No. 3 (MR METHOD), only memory channels that have the same band data can be recalled {see below}. n Using a Numeric keypad You can also recall a memory channel by entering a desired memory channel number with the keypad. 1 Select the desired band. 2 Press [MR] to enter Memory Recall mode. 3 Press [ENT], then enter the channel number using 3 digits. For example, to recall channel 12, press [ENT],
[0], [1], [2]. You can shorten the entry for memory channels that are less than 100 by pressing [ENT] after entering the channel number. For example, to recall memory channel 9, press [ENT], [9],
[ENT]. Note:
u You cannot recall an empty memory channel. An error beep sounds. u When you recall an odd-split memory channel, + and appear on the display. Press [REV] to display the transmit frequency. u After recalling a memory channel, you may program data such as Tone or CTCSS. These settings, however, are cleared once you select another channel or the VFO mode. To permanently store the data, overwrite the channel contents {page 15}. CLEARING A MEMORY CHANNEL To clear an individual memory channel:
1 Recall the memory channel you want to erase. 2 Switch the transceiver OFF. 3 Press [MR]+ [
]. An erase confirmation message appears. 16 NAMING A MEMORY CHANNEL You can name memory channels using up to 8 alphanumeric characters. When you recall a named memory channel, its name appears on the display in place of the stored frequency. Names can be call signs, repeater names, cities, names of people, etc. 1 Press [MR] to recall your desired memory channel. 2 Press [F], [MN<->f] to enter memory name input mode. The entry cursor appears. 3 Turn the Tuning control or press [
]/ [
] to select the first character. You can enter alphanumeric characters plus special ASCII characters. Refer to the following table for the available characters. 4 Press [sssss]. The cursor moves to the next digit. 5 Repeat steps 3 and 4 to enter up to 8 digits. Pressing [sssss] after selecting the 8th digit completes the programming. To complete programming after entering less than 8 digits, press [sssss] twice. Press [ttttt] to move the cursor back. Pressing [F] deletes the character at the cursor position. You can also use the keypad to enter alphanumeric characters, in step 3. For example, each press of
[2] sets the entry as a, b, c, 2, A, B, C, and then back to a. Press [0] to enter a space or 0. After storing a memory name, pressing [MN<->f]
switches the display between the memory name and the frequency. Note:
u You can also name the DTMF memory channels {page 31} and Information Channels {page 20} but you cannot name the Call channel {page 19}. u You cannot assign a memory name to a channel that does not contain data. u You can overwirite stored names by repeating steps 1 to 5. u The stored name is erased when you clear the memory channel data. 8 MEMORY CHANNELS Available characters using the Tuning control Available characters A K U
`
j t
~
(
2
<
S E C D B O L M N Y V W X d c a n m k x u w
"
!
,
+
5 6
? @
b l v PS
*
4
>
\
) 3
=
F P Z e o y
#
7 H R
]
g q
{
G I Q S
^
[
f h p r z
|
$ % &
. 0
:
8
/
9 J T _ i s
}
1
;
Additional characters for the TH-F7E s y Y sretcarahcelbaliavA Available characters using the numeric keypad FMTD yek 1 2 3 4 5 6 7 8 9 0 Z A D G J M P T W q a d g j m p t w Q 2 3 4 5 6 7 8 9 B E H K N R U X 1 c f i l o s v y C F I L O S V Y ecaps
#
?
&
:
z b e h k n r u x 0
!
#
"
.
)
,
<
>
/
;
'
(
@
17 ERASING MEMORY CHANNELS USING MEMORY GROUP DELETE Instead of erasing each unnecessary channel one by one, you can erase an entire group of memory channels at once. For example, if you erase group 2 memory channels, all the data in memory channels 100 ~ 149 are erased. 1 Press [MR]. Turn the Tuning control or press [
]/ [
] to select a memory channel in the group you want to erase (for example, memory channel No. 111, in Group 2). 2 Press [
] (POWER) to turn the transceiver OFF. 3 Press [
] (POWER) + [MHz]. An erase confirmation message appears. 4 Press [MR], [sssss] or [MNU] to proceed. Otherwise, press any other key to cancel the erase. MEMORY TRANSFER n Memory \ VFO Transfer After retrieving frequencies and associated data from Memory Recall mode, you can copy the data to the VFO. This function is useful, for example, when the frequency you want to monitor is near the frequency stored in a memory channel. 1 Press [MR], then turn the Tuning control to recall a desired memory channel. 2 Press [F], [MR] to copy the memory channel data to the VFO. n Channel \ Channel Transfer You can also copy channel information from one memory channel to another. This function is useful when storing frequencies and associated data that you temporarily change in Memory Recall mode. 1 Press [MR], then turn the Tuning control to recall a desired memory channel. 2 Press [F]. 3 Select the memory channel where you would like the data copied, using the Tuning control. 4 Press [MR]. 8 MEMORY CHANNELS MEMORY CHANNEL GROUPS 400 memory channels have been divided into 8 groups of 50. Group 0 contains memory channel numbers 0 ~ 49, group 1 is 50 ~ 99, group 2 is 100 ~
149, and so on. You can categorize each group to store similar data, same frequency bands or same modes for ease of use.
#puorG 0puorG 1puorG 2puorG 3puorG lennahcyromeM 94~0 99~05 941~001 991~051
#puorG 4puorG 5puorG 6puorG 7puorG lennahcyromeM 942~002 992~052 943~003 993~053 RECALLING A MEMORY CHANNEL USING MEMORY GROUP FUNCTION It is sometimes a tedious endeavor to scroll through 400 memory channels sequencially. However, using a Group memory recall function, you can access your desired memory channel numbers more quickly. 1 Press [MR] to enter Memory Recall mode. 2 While pressing and holding [LAMP], turn the Tuning control to select a group. Each click of the Tuning control, the lowest memory channel number of each group is recalled. For example, if you have the following memory channels that contain data:
#puorG 0puorG 1puorG 2puorG 3puorG 4puorG 5puorG 6puorG 7puorG atadehtniatnoctahtslennahcyromeM 2 16 111 661 082 223 0 05 301 251 062 503 993 51 87 03 89 54 01 56 321 333 543 Memory channels 0, 50, 103, 152, 260, 305, 399, and then 0 are recalled sequencially while pressing and holding [LAMP]. 3 Release [LAMP] and turn the Tuning control to select the desired memory channels within the selected group. Note: If you have configured the Menu No. 3 as CURRENT BAND
{page 16}, only memory channels that have the same frequency band are recalled. 18 993~00lennahC ycneuqerfevieceR ycneuqerftimsnarT ycneuqerfenoT noitceridtfihS ycneuqerfSSCTC edocSCD SCD/SSCTC/enoT sutatsFFO/NO noitceridtesffO NOesreveR ezispetsycneuqerF lennahcyromeM eman NOgninutENIF noitcelesedoM lennahCyromeM FFO/NOtuokcoL 993~0lennahC ycneuqerfevieceR ycneuqerftimsnarT ycneuqerfenoT noitceridtfihS ycneuqerfSSCTC edocSCD SCD/SSCTC/enoT sutatsFFO/NO noitceridtesffO NOesreveR ezispetsycneuqerF lennahcyromeM eman NOgninutENIF noitcelesedoM lennahCyromeM NOtuokcoL a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 993~00lennahC ycneuqerfevieceR ycneuqerftimsnarT ycneuqerfenoT noitceridtfihS ycneuqerfSSCTC edocSCD SCD/SSCTC/enoT sutatsFFO/NO noitceridtesffO NOesreveR ezispetsycneuqerF lennahcyromeM eman NOgninutENIF noitcelesedoM lennahCyromeM FFO/NOtuokcoL 2rP,1rP,9U/9L~0U/0L ycneuqerfevieceR ycneuqerftimsnarT ycneuqerfenoT noitceridtfihS ycneuqerfSSCTC edocSCD SCD/SSCTC/enoT sutatsFFO/NO noitceridtesffO NOesreveR ezispetsycneuqerF lennahcyromeM eman NOgninutENIF noitcelesedoM lennahCyromeM FFOtuokcoL The tables above illustrate how data is transferred between memory channels. 8 MEMORY CHANNELS CALL CHANNEL The Call channel can be recalled instantly no matter what frequency the transceiver is operating on. For instance, you may use the Call channel as an emergency channel within your group. In this case, the Call scan {page 24} will be useful. The default Call channel frequencies are 144.000 MHz for the 144 MHz band, 223.000 MHz for 220 MHz band (TH-F6A), 430.000 MHz (TH-F7E)/
440.000 MHz (TH-F6A) for the 430/ 440 MHz band. Each Call channel can be reprogrammed either as a simplex or odd-split channel. Note: Unlike memory channels 0 to 399, the Call channel cannot be cleared. Clearing the Call channel will set it to the factory default values. n Recalling the Call Channel 1 Press [BAND] to select an amateur radio band. 2 Press [CALL] to recall the Call channel for that operating band. The call channel frequency and C appear. To return to the previous frequency, press
[CALL] again. n Reprogramming the Call Channel 1 Press [BAND] to select your desired amateur radio band. 2 Select your desired frequency and related data
(Tone, CTCSS, DCS, or Shift, etc.). When you program the Call channel as an odd-split channel, select a receive frequency first. 3 Press [F], [CALL]. The selected frequency and related data are stored in the Call channel for the selected band. To also store a separate transmit frequency, continue with the following steps. 4 Select the desired transmit frequency. 5 Press [F]. 6 Press [PTT]+[CALL]. The separate transmit frequency is stored in the Call channel. Note:
u The transmit frequency must be on the same band as the receive frequency band. u Call channel data is shared between the A and B-band. u Transmit offset status and Reverse status are not stored in an odd-split Call channel. u To store transceiver configurations other than frequencies, select the configurations in step 3 not step 5. 19 n Reprogramming the Information Channel 1 Press [VFO]. 2 Select a desired frequency and mode. 3 Press [F]. 4 Turn the Tuning control or press [
]/ [
] to select the memory channel (I0 to I9) in which you want to store the data. 5 Press [MR]. A long beep sounds and the Information channel data is now revised. 8 MEMORY CHANNELS INFORMATION CHANNELS 10 Information channels are available for storing radio broadcasting service frequencies, such as weather radio stations and community FM broadcasting stations. For your conveniences, pressing [INFO] instantly recalls the Information channel to B-band. Unlike regular memory channels, you cannot store a transmit frequency in an Information channel. The following frequency data is stored by default. rebmunlennahC emaNyromeM/edoM/ycneuqerF A6F-HT E7F-HT 1I 2I 3I 4I 5I 6I 7I 8I 9I 0I
/MF/zHM055.261 REHTAEW
/MF/zHM004.261 REHTAEW
/MF/zHM574.261 REHTAEW
/MF/zHM524.261 REHTAEW
/MF/zHM054.261 REHTAEW
/MF/zHM005.261 REHTAEW
/MF/zHM525.261 REHTAEW
/MF/zHM056.161 REHTAEW
/MF/zHM577.161 REHTAEW
/MF/zHM572.361 REHTAEW
)ytpmE(atadoN You can revise the default channel data, such as the receiving frequencies, modes, and memory names. n Recalling an Information Channel 1 Select your desired band. 2 Press [INFO] to recall the Information channels. In appears, where n is the Information channel number from (0 ~ 9). If the B-band is selected for operation, you
]/ [
can turn the Tuning control or press [
to select other Information channels.
]
To exit the Information channel mode, press
[VFO] or [MR]. Note: If you press [MN<->f], you can display the receiving frequency in place of the memory name. 20 8 MEMORY CHANNELS CHANNEL DISPLAY While in this mode, the transceiver displays only memory channel numbers (or memory names if stored) instead of frequencies. 1 Press [
] (POWER) + [A/B]. The transceiver displays the memory channel number in place of the operating frequencies. 2 Turn the Tuning control or press [
]/ [
your desired memory channel number.
] to select To recover normal operation, press [
[A/B] again.
] (POWER) +
Note:
u To enter Channel Display mode, you must have at least one memory channel that contains the data. u If the memory channel contains the memory name data, the memory name is displayed in place of the memory channel number. 21 NORMAL SCAN When you are operating the transceiver in VFO mode, 3 types of scanning are available: Band Scan, Program Scan, and MHz Scan. BAND SCAN The transceiver scans the entire band of the frequency you selected. For example, if you are operating and receiving at 144.525 MHz on the A-band, it scans all the frequencies available for the 144 MHz band. (Refer to receiver VFO frequency range in the specifications {page xx}). When the current VFO receive frequency is outside of the Program Scan frequency range {below}, the transceiver scans the entire frequency range available for the current VFO. 1 Press [VFO]. 2 Press [BAND] to select your desired band. 3 Turn the Tuning control or press [
] to select
]/ [
the frequency outside of the Program Scan frequency range {below}. 4 Press [VFO] (1 s) to start the Band Scan. 5 To stop the Band Scan, press [VFO] or [PTT]. Note:
u While scanning, you can change the scan frequency direction by turning the Tuning control or press [ ]/ [ ]. u If you select a frequency within the L0/ U0 ~ L9/ U9 range in step 3, the Program Scan {below} starts. u If you press [MONI], Band Scan temporarily pauses. Release
[MONI] to resume scanning. u The transceiver stops scanning in only the AM and FM modes when it detects a signal. u If the Fine Tuning function is ON, scanning does not stop at the busy channels. u If you press any ot the following keys during the scan, the transceiver exits the Scan: [F], [F] (1 s), [LAMP], [MONI],
[SQL], Tuning control, [ ], and [ ]
SCAN Scan is a useful function for hands-off monitoring of your favorite frequencies. By becoming comfortable with all types of Scan, you will increase your operating efficiency. This transceiver provides the following types of scans. epyTnacS esopruP nacSdnaB lamroN nacS margorP nacS nacSzHM lennahC-llA nacS nacSpuorG OFV yromeM lennahC yromeM nacS llaC nacS nacSytiroirP lennahCnoitamrofnI nacS lausiV
*nacS OFV yromeM lennahC ehtfodnaberitneehtsnacS detcelesuoyycneuqerf deificepsehtsnacS niderotssegnarycneuqerf
~0U/0LslennahcyromeM 9U/9L nihtiwseicneuqerfehtsnacS egnarzHM1a
,slennahcyromeMllasnacS 993ot0morf yromeMdeificepsehtsnacS spuorglennahc dnalennahcllaCehtsnacS ycneuqerfOFVtnerruceht dnalennahcllaCehtsnacS lennahcyromeMdetceleseht ehtnoseitivitcaehtskcehC slennahcytiroirpdeificeps sdnoces6yreve noitamrofnIehtsnacS slennahc snacS ehtniseicneuqerf5 raenezispetsdemmargorp gnitarepotnerruceht langisehT.ycneuqerf siycneuqerfhcaefohtgnerts hparg-rabanideyalpsid slennahcyromeMehtsnacS langisehtsyalpsiddna anilennahchcaefohtgnerts hparg-rab
*Visual Scan graphically shows the busy status of frequencies in a specific range. Note:
u While using CTCSS or DCS, Scan unmutes only for the signals that contain the same CTCSS tone or DCS code that you selected. u Pressing and holding [PTT] causes Scan to stop. u Starting Scan switches OFF the Automatic Simplex Checker
(ASC) {page 14}. 22 14 SCAN MHz SCAN MHz Scan allows you to scan an entire 1 MHz frequency range within the current VFO frequency. 1 Press [VFO]. 2 Turn the Tuning control or press [
] to select a frequency in which to perform the MHz Scan. If you want to scan the entire 145 MHz frequency, select any frequency between 145.000 and 149.995 MHz (for example, select 145.650 MHz). Scan will operate between 145.000 MHz and 145.999 MHz.
]/ [
3 Press [MHz] (1 s) to start the MHz Scan. 4 To stop the MHz Scan, press [MHz] or [PTT]. Note:
u If the Fine Tuning function is ON, you cannot perform the MHz Scan. u The transceiver stops scanning in only the AM and FM modes when it detects a signal. u If you press [MONI], MHz Scan temporarily pauses. Release
[MONI] to resume scanning. u If you press any of the following keys during the scan, the transceiver exits the Scan: [F] (1 s), [LAMP], [MONI], [SQL], Tuning control, [ ], and [ ]
u When the CTCSS or DCS function is activated, the transceiver stops at a busy frequency and decodes the CTCSS tone or DCS code. If the tone or code matches, the transceiver unmutes. Otherwise, it resumes scanning. PROGRAM SCAN You can limit the scanning frequency range. There are 10 memory channel pairs (L0/ U0 ~ L9/ U9) available for specifying the start and end frequencies. It monitors the range between the start and end frequencies that you have stored in memory channels L0/ U0 to L9/ U9. Before performing the Program Scan, store the Program Scan frequency range to one of the memory channels L0/ U0 ~ L9/ U9. n Storing Program Scan Frequency Range 1 Press [VFO]. 2 Press [BAND] to select your desired band. 3 Turn the Tuning control or press [
]/ [
your desired start frequency.
] to select 4 Press [F], then turn the Tuning control or press
[
]/ [
] to select a memory channel from L0 ~ L9. 5 Press [MR] to store the start frequency in the memory channel. 6 Turn the Tuning control or press [
your desired end frequency.
]/ [
] to select
]/ [
7 Press [F], then Turn the Tuning control or press
[
] to select the corresponding channel from U0 ~ U9 (you must select the same numeric value as in step 4). For example, if you selected L0 in step 4, you must select U0 in this step. 8 Press [MR] to store the end frequency in the memory channel. n Performing the Program Scan 1 Press [VFO]. 2 Turn the Tuning control or press [
] to select a frequency within the frequency range of memory channel L0/ U0 ~ L9/ U9.
]/ [
3 Press [VFO] (1 s) to start the Program Scan. 4 To stop the Program Scan, press [VFO] or [PTT]. Note:
u If you press [MONI], Program Scan temporarily pauses. Release
[MONI] to resume scanning. u The transceiver stops scanning only in the AM and FM modes when it detects a signal. u If the Fine Tuning function is ON, the scanning does not stop at the busy channels. u If you press any of the following keys during the scan, the transceiver exits the Scan: [F] (1 s), [LAMP], [MONI], [SQL], Tuning control, [ ], and [ ]
23 14 SCAN MEMORY SCAN Memory Scan monitors all memory channels in which you have stored frequencies (All-Channel Scan) or only a desired group of memory channels (Group Scan). ALL-CHANNEL SCAN The transceiver scans all of the memory channels in which you have stored frequencies. 1 Press [MR] (1 s). Scan starts from the last memory channel number and ascends up through the channel numbers (default). Turn the Tuning control or press [
] to change the scanning direction. To jump to a desired channel while scanning,
]/ [
quickly turn the Tuning control. 2 To stop the All-Channel Scan, press [MR] or
[PTT]. Note:
u If the Fine Tuning function is ON, you cannot perform the All-
Channel Scan. u If you press [MONI], All-Channel Scan temporarily pauses. Release [MONI] to resume scanning. u The transceiver stops scanning in all modes when it detects the signal. u If you press any of the following keys during the scan, the transceiver exits the Scan: [F] (1 s), [LAMP], [MONI], [SQL], Tuning control, [ ], and [ ]
GROUP SCAN In order to easily manage all 400 memory channels, they are divided into 8 groups {page 18}. For the purpose of Group Scan, you can select a particular memory group to be scanned, depending on the situation. Using the Memory Group Link function
{below}, you can scan all the linked memory groups. 1 Press [MR] to enter Memory Scroll mode. 2 Turn the Tuning control or press [
] to select a memory channel in the group you want to scan. For example, if you want to scan the group 0 memory channels, recall memory channel 12
(group 0 contains memory channels 0 ~ 49).
]/ [
3 Press [MHz] (1 s). Note:
u If the Fine Tuning function is ON, you cannot perform the Group Scan. u If you press [MONI], All-Channel Scan temporarily pauses. Release [MONI] to resume scanning. u The transceiver stops scanning in all modes when it detects a signal. u If you press any of the following keys during the scan, the transceiver exits the Scan: [F] (1 s), [LAMP], [MONI], [SQL], Tuning control, [ ], and [ ]
n Memory Group Link Although the 400 memory channels are divided into 8 groups {page 18}, you may sometimes want to scan two or more groups. In this case, use the Memory Group Link function. 1 Press [MNU] to enter Menu mode. 2 Turn the Tuning control or press [
] to select
]/ [
Menu No. 2 (M.GRP LINK). 3 Press [sssss] or [MNU]. The memory group numbers appear. 4 Move the cursor using [ttttt]/ [sssss], then turn the Tuning control or press [
deselect the group to be linked. Linked groups appear at the bottom of the
] to select or
]/ [
display (in the example below, groups 0, 1, 3 and 5 are linked). 5 Press [MNU] to store the setting. Otherwise, press [PTT] to cancel. The memory channels within the selected group are scanned. If the group is linked to other groups {below}, all the linked groups are also scanned. 4 To stop the Group Scan, press [MHz] or [PTT]. 24 CALL SCAN A Call channel can be stored for each amateur radio band, such as the 144 MHz, 430/ 440 MHz, and 220 MHz (TH-F6A only) bands {page 19}. You can monitor one of these Call channels and the current operating frequency alternatively. 1 Select the frequency (in VFO or Memory Recall mode) you want to monitor.
]/ [
] to select the desired frequency. In VFO mode, press [A/B] to select the A or B-band. Then, turn the Tuning control or press
[
In Memory Recall mode, turn the Tuning control or press [
channel you want to monitor.
] to select a memory
]/ [
2 Press [CALL] (1 s) to start the Call Scan. 3 The Call channel for the band and the selected VFO frequency or memory channel are monitored alternatively. 4 To stop the Call Scan, press [PTT] or [CALL]. Note:
u If you press [MONI], Call Scan temporarily pauses. Release
[MONI] to resume scanning. u The transceiver stops scanning in all modes when it detects a signal. u If you press any of the following keys during the scan, the transceiver exits the Scan: [F] (1 s), [LAMP], [MONI], [SQL], and the Tuning control 14 SCAN PRIORITY SCAN You may sometimes want to check your favorite frequency activities while monitoring the A and B-bands. In this case, use the Priority Scan function. It checks the activities of Pr1 and Pr2 channels every 6 seconds, alternatively, using the B-band receiver. If the transceiver detects a signal on Pr1 or Pr2, it recalls the frequency to the B-band receiver. Note: If you do not operate any control or key for 3 seconds after the signal drops, the transceiver resumes Priority Scan. n Programming Priority channels 1 Press [VFO]. 2 Turn the Tuning control or press [
]/ [
your desired priority channel frequency.
] to select 3 Select the mode and selective call functions if necessary. 4 Press [F]. The memory channel number appears. 5 Turn the Tuning control or press [
Pr1.
]/ [
] to select 6 Press [MR] to store the data on the priority channel. If you want to store a second priority channel, repeat steps 1 ~ 6 and select Pr2 in step 5. Note: You can program any frequency available on the B-band as a priority channel. 25 VISUAL SCAN While you are receiving, Visual Scan allows you to monitor frequencies near the current operating frequency. Visual Scan graphically displays the busy status of all frequencies in the selected range. You will see a maximum of 7 segments, for each frequency (channel) point that represent relative S-
meter levels. The Visual Scan monitors 5 channels (frequencies) by centering on the current channel (frequency). In this way, a total of 11 channels (frequencies) signal strength status are graphically displayed. Note: When you perform the Visual scan on the A-band, the transceiver can output the audio. However, when you perform the Visual Scan on the B-band, it cannot output the audio. n Using Visual Scan (VFO) 1 Select your desired band for Visual Scan. 2 Turn the Tuning control or press [
]/ [
] to select your desired center frequency. The transceiver scans the 5 upper frequencies and 5 lower frequencies using the current VFO frequency step. 3 Press [F], [INFO] to start Visual Scan (VFO). The scanning frequency is displayed on the current operating band and the relative S-meter level of each frequency appears on the other band display. To pause Scan, press and hold [MONI]. While the Visual Scan is paused, you can monitor the paused frequency. Release
[MONI] to resume the Visual Scan. 4 To change the current scanning frequency, Turn the Tuning control or press [
The displayed frequency changes and the
]/ [
]. cursor moves. 5 To stop the Visual Scan, press [F], [INFO]. Note:
u If you press [MONI], Visual Scan temporarily pauses. Release
[MONI] to resume scanning. When it is paused, the center frequency bar-graph blinks. u Although you can perform the Visual Scan on the A or B-band, the B-band cannot output the audio during the scan. u You can press [PTT] or [CALL] (if 1750 Hz is programmed) to transmit during the scan. u If the Fine Tuning function is ON, the Visual Scan cancels the FINE function and automatically adjusts the frequency to the next available frequency. 14 SCAN n Using Priority Scan 1 Press [F], [BAL]. P appears. The transceiver checks for a signal on the Pr1 and Pr2 channels every 6 seconds, alternatively. When the transceiver detects a signal on the priority channel, the B-band frequency changes to the priority channel. If you do not operate any control or key for 3 seconds after the signal drops, the transceiver resumes Priority Scan. 2 To quit Priority Scan, press [F], [BAL] again. Note:
u The signal being received on the B-band may become intemittent beuase the Priority Scan uses the B-band receiver to check the priority channel(s) activities. u If you press any of the keys below during the scan, the transceiver exits the scan: [A/B], [LAMP], [MONI], [SQL],
[F] (1s), [BAL], and [F] then [BAL]
u When a signal is received on a Priority channel with a CTCSS or DCS code programmed, the Priority channel is recalled even if a different selective tone/ code is detected. However, the transceiver only unmutes if the signal has the same CTCSS tone or DCS code. u Press and hold [MONI] to pause the Priority Scan when the transceiver is not displaying a priority channel. Release [MONI]
to resume the Priority Scan. INFORMATION CHANNEL SCAN Information channel scan is similar to group scan. However, it scans only Information channels. 1 Press [INFO]. The last Information channel you used is recalled. 2 Press [INFO] (1 s) to start the Information Channel Scan. 3 To stop the Information Channel Scan, press
[INFO] or [PTT]. Note:
u If you press [MONI], Information Channel Scan temporarily pauses. Release [MONI] to resume scanning. u The transceiver stops scanning in all modes when it detects a signal. u If you press any of the following keys during the scan, the transceiver exits the Scan: [F] (1 s), [LAMP], [MONI], [SQL], Tuning control, [ ], and [ ]
26 n Using Visual Scan (Memory Channel) 1 Press [MR] to enter Memory Recall mode.
] to 2 Turn the Tuning control or press [
select your desired center memory channel.
]/ [
3 Press [F], [INFO] to start the Visual Scan. 4 The transceiver start scanning the 5 upper memory channels and 5 lower memory channels, by centering the selected memory channel. The current scanning memory channel number and frequency are displayed on the current operating band. On the other band, the relative S-meter level of each frequency channel is displayed. To pause Scan, press [MONI]. While the Visual Scan is paused, you can monitor the paused frequency. Press [MONI] again to resume the Visual Scan. 6 To change the current scanning channel, turn the Tuning control or press [
]/ [
]. 7 To stop the Visual Scan, press [F], [INFO]. Note:
u If you press [MONI], Visual Scan temporarily pauses. Release
[MONI] to resume scanning. When it is paused, the center frequency bar-graph blinks. u Although you can perform the Visual Scan on the A or B-band, the B-band cannot output the audio during the scan. u You can press [PTT] or [CALL] (if 1750 Hz is programmed) to transmit during the scan. u If the Fine Tuning function is ON, the Visual Scan cancels the FINE function and automatically adjusts the frequency to the next available frequency. 14 SCAN SCAN RESUME METHOD The transceiver stops scanning at the frequency (or memory channel) where a signal is detected. It then continues or stops scanning according to which resume mode you have selected. You can choose one of the following modes. The default is Time-
operated mode. Time-Operated mode (default) The transceiver remains on a busy frequency (or memory channel) for approximately 5 seconds, then continues to scan, even if the signal is still present. Carrier-Operated mode The transceiver remains on the busy frequency (or memory channel) until the signal drops out. There is a 2 second delay between signal dropout and scan resumption. Seek mode The transceiver moves to a frequency or memory channel where a signal is present and stops. To change the scan resume method:
1 Press [MNU]. 2 Turn the Tuning control or press [
Menu No. 1 (SCAN RESUME).
]/ [
] to select 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
]/ [
] to select TIME (Time-Operated mode), CARRIER
(Carrier-Operated mode), or SEEK (Seek mode). 5 Press [sssss] or [MNU] to store the setting. Otherwise, press [ttttt] or [PTT] to cancel. MEMORY CHANNEL LOCKOUT You can lock out memory channels that you prefer not to monitor during Memory Scan. 1 Press [MR] to enter Memory Recall mode. 2 Turn the Tuning control or press [
]/ [
the memory channel to be locked out.
] to select 3 Press [F], [MHz]. appears at the top right of the memory channel number, indicating the channel is locked out. 4 To unlock the memory channel, repeat steps 1 ~ 3. disappears. 27 SELECTIVE CALL CTCSS and DCS You may sometimes want to hear calls from only specific persons or groups. In this case, use the selective call function. This transceiver is equipped with CTCSS (Continuous Tone Coded Squelch System) and DCS (Digital Coded Squelch). These selective calls allow you to ignore (not hear) unwanted calls from other persons who are using the same frequency. The transceiver unmutes only when it receives the signal having the same CTCSS tone or DCS code. Note:
u CTCSS and DCS do not cause your conversation to be private or scrambled. It only relieves you from listening to unwanted conversations. u CTCSS and DCS function in only FM mode. CTCSS (Continuous Tone Coded Squelch System) A CTCSS tone is a sub-audible tone and is selectable from among the 42 tone frequencies listed in the table on the following page. The list includes 37 EIA standard tones and 5 non-standard tones. You can select one of the tones to use as a CTCSS tone. USING CTCSS 1 Press [TONE] until CT appears. Each time you press [TONE], the icon cycles as follows: T (TONE) DCS (DCS)
(OFF) CT (CTCSS) T (TONE). STSTA CONCON PACKET9696BCONDUP 7 9 5 STSTA CONCON PACKET9696BCONDUP 7 9 5 STSTA CONCON PACKET9696BCONDUP 7 9 5 When the CTCSS funtion is ON, you will hear calls only when the selected CTCSS tone is received. To answer the call, press and hold the PTT switch, then speak into the microphone. Note:
u You cannot use the CTCSS and Tone/ DCS functions simultaneously. Switching the CTCSS function ON after having activated the Tone/ DCS functions deactivates the Tone/ DCS functions. u If you select a high CTCSS frequency, receiving audio or noise that contains the same frequency portions may cause CTCSS to function incorrectly. To prevent noise from causing this problem, select an appropriate squelch level {page x}. SELECTING A CTCSS FREQUENCY 1 While in CTCSS mode {above}, press [F],
[TONE]. The current CTCSS frequency appears. 2 Turn the Tuning control or press [
]/ [
] to select your desired CTCSS frequency. The selectable CTCSS frequencies are the same as those for the Tone frequency. Refer to the table on the following page for the available CTCSS frequencies. 3 Press [sssss] or [MNU] to store the new setting. Otherwise, press [ttttt] or [PTT] to cancel. POWER OK DATA AX.25PROTOCOL E S C A/B MENU BAL MSG REV MHz TNC LIST DUP DUAL POS BCON MNf ENT VFO MR CALL STSTA CONCON PACKET9696BCONDUP 7 9 5 28 CTCSS FREQ. ID SCAN This function scans through all CTCSS frequencies to identify the incoming CTCSS frequency on the received signal. You may find this useful when you cannot recall the CTCSS frequency that the other persons in your group are using. 1 While the CTCSS function is ON, press [TONE]
(1 s) to start the CTCSS Freq. ID Scan function. 7 SELECTIVE CALL DCS (Digital Coded Squelch) DCS is similar to CTCSS. However, instead of using an analog signal, it uses a continuous sub-audible digital wave form that represents a 3-digit octal number. You can select a DCS code from among the 104 DCS codes listed in the table below. USING DCS 1 Press [TONE] until DCS appears. Each time you press [TONE], the icon cycles as follows: T (TONE) DCS (DCS)
(OFF) CT (CTCSS) T (TONE). To reverse the scan direction, turn the Tuning control or press [
]/ [
]. To quit the function, press [ttttt]. When a CTCSS frequency is identified, the identified frequency appears and blinks. 2 Press [sssss] or [MNU] to program the identified frequency in place of the current CTCSS frequency. Otherwise, press [ttttt] if you do not want to program the identified frequency. Turn the Tuning control or press [
]/ [
] while the identified frequency is blinking to resume scanning. Available CTCSS frequencies
.oN 10 20 30 40 50 60 70 80 90 01 11
.qerF
)zH(
0.76 3.96 9.17 4.47 0.77 7.97 5.28 4.58 5.88 5.19 8.49
.oN 21 31 41 51 61 71 81 91 02 12 22
.qerF
)zH(
4.79 0.001 5.301 2.701 9.011 8.411 8.811 0.321 3.721 8.131 5.631
.oN 32 42 52 62 72 82 92 03 13 23 33
.qerF
)zH(
3.141 2.641 4.151 7.651 2.261 9.761 8.371 9.971 2.681 8.291 5.302
.oN 43 53 63 73 83 93 04 14 24
.qerF
)zH(
5.602 7.012 1.812 7.522 1.922 6.332 8.142 3.052 1.452 Note:
u Received signals are monitored through the speaker while scanning is in progress. u If the CTCSS function is activated for both the A and B-band, the scan speed may be slower. When the DCS function is ON, you will hear calls only when the selected DCS code is received. To answer the call, press and hold the PTT switch, then speak into the microphone. Note: You cannot use the DCS funtion and CTCSS/ Tone functions simultaneously. Switching the DCS function ON after having activated the CTCSS/ Tone functions deactivate the CTCSS/ Tone functions. SELECTING A DCS CODE 1 While in DCS mode {above}, press [F], [TONE]. The current DCS code appears. 2 Turn the Tuning control or press [
]/ [
] to select your desired DCS code. The available DCS codes are shown in the following table. 320 520 620 130 230 630 340 740 150 350 450 560 170 270 370 470 411 511 611 221 521 131 231 431 341 541 251 551 651 261 561 271 471 502 212 322 522 622 342 442 542 642 152 252 552 162 362 562 662 172 472 603 113 513 523 133 233 343 643 153 653 463 563 173 114 214 314 324 134 234 544 644 254 454 554 264 464 564 664 305 605 615 325 625 235 645 565 606 216 426 726 136 236 456 266 466 307 217 327 137 237 437 347 457 3 Press [sssss] or [MNU] to store the new setting. Otherwise, press [ttttt] or [PTT] to cancel. 29 7 SELECTIVE CALL DCS CODE ID SCAN This function scans through all DCS codes to identify the incoming DCS code on the received signal. You may find this useful when you cannot recall the DCS code that the other persons in your group are using. 1 While in DCS mode, press [TONE] (1 s) to start the DCS Code ID Scan function. To reverse the scan direction, turn the Tuning control or press [
]/ [
]. To quit the function, press [ttttt]. When a DCS code is identified, the identified code appears and blinks. 2 Press [sssss] or [MNU] to program the identified frequency in place of the current DCS code. Otherwise, press [ttttt] if you do not want to program the identified code. Turn the Tuning control or press [
]/ [
] while the identified DCS code is blinking to resume scanning. Note:
u Received signals are monitored through the speaker while scanning is in progress. u If the DCS function is activated for both the A and B-band, the scan speed may be slower. 30 DTMF FUNCTIONS The keys on the keypad also function as DTMF keys;
the 12 keys found on a push-button telephone plus 4 additional keys (A, B, C, D). This transceiver also provides 10 dedicated DTMF memory channels. You can store a DTMF number (16 digits max.) with a memory name (8 digits max.) in each of the channels to recall later for a speed dialingl. Many repeaters in the U.S.A. and Canada offer a service called Autopatch. You can access the public telephone network via such a repeater by sending DTMF tones. For further information, consult your local repeater reference. MANUAL DIALING Manual Dialing requires only two steps to send DTMF tones. 1 Press and hold the PTT switch to transmit. 2 While transmitting, press the keys in sequence on the keypad to send DTMF tones. The corresponding DTMF tones are transmitted and monitored through the speaker. AUTOMATIC DIALER If you use the 10 dedicated memory channels to store DTMF numbers, you need not remember a long string of digits. n Storing a DTMF Number in Memory Note: Audible DTMF tones from other transceivers near you (or from your own speaker) may be picked up by your microphone. If so, you may fail to correctly program a DTMF number. 1 Press [MNU] to enter Menu mode. 2 Turn the Tuning control or press [
]/ [
] to select the Menu No. 10 (DTMF STORE). 3 Turn the Tuning control or press [
]/ [
select a desired DTMF memory channel number from 0 to 9. 4 Press [sssss] or [MNU].
] to
)zH(.qerF 9021 6331 7741 3361 796 077 258 149 1 4 7 2 5 8 0 3 6 9 A B C D n TX Hold The display for entering a memory name appears; the first digit blinks. To skip naming the channel, press [sssss] or
[MNU] again. You can jump to step 8. This function makes the transceiver remain in transmit mode for 2 seconds after you release each key. So you can release the PTT switch while sending the DTMF tones. 1 Press [MNU] to enter Menu mode. 2 Turn the Tuning control or press [
]/ [
select the Menu No. 12 (DTMF HOLD).
] to 5 Turn the Tuning control or press [
]/ [
] to select a character. You can enter alphanumeric characters plus special ASCII characters.
[MONI] to delete a charactor on the cursor. You can also use the numeric keypad to enter a character (Special ASCII charactors are not available). 3 Turn the Tuning control or press [
select ON.
]/ [
] to 4 Press [sssss] or [MNU] to store the setting. Otherwise, press [ttttt] or [PTT] to cancel. Press [LAMP]+turning Tuning control to jump to the first charactor of each character type in the ASCII table. 6 Press [sssss] to move the cursor to the next digit. 7 Repeat steps 5 and 6 to enter up to 8 digits. Pressing [sssss] after selecting the 8th digit causes the cursor to move to the start of the next field. To complete programming the name less than 8 digits, press [sssss] twice. 31 8 DTMF FUNCTIONS Each press of [ttttt] causes the cursor to move backward. 8 Press the keys in sequence on the keypad to enter a DTMF number with up to 16 digits. You can also turn the Tuning control or
]/ [
] to select the required DTMF press [
number for each digit. Select a space if you want to put a pause. 9 Press [sssss] or [MNU] to complete the programming. You can confirm the stored DTMF number by using steps 1 to 3. You can also use the keypad to enter alphanumeric characters in step 5. For example, each press of [BAND] switches entry as A, B, C, a, b, c, then 2. n Transmitting a Stored DTMF Number 1 Press [PTT]+[MNU]. n Adjusting the DTMF tone tranmission speed This transceiver allows you to configure the DTMF number transmission speed between Fast
(default) and Slow. If a repeater cannot respond to the fast speed, adjust this parameter. 1 Press [MNU] to enter Menu mode. 2 Turn the Tuning control or press [
]/ [
select the Menu No. 11 (DTMF SPD).
] to 3 Press [sssss] or [MNU]
4 Turn the Tuning control or press [
select FAST (default) or SLOW. The tone duration of FAST is 50 ms and
] to
]/ [
SLOW is 100 ms. 5 Press [sssss] or [MNU] to store the new setting. n Adjusting the pause duration You can also change pause duration (a space digit) stored in memory channels; the default is 500 msec. 1 Press [MNU] to enter Menu mode. 2 Turn the Tuning control or press [
] to
]/ [
select the Menu No. 13 (DTMF PAUSE). 3 Press [sssss] or [MNU]
4 Turn the Tuning control or press [
]/ [
] to select 100/ 250/ 500 (default)/ 750/ 1000/ 1500/
2000 msec. 5 Press [sssss] or [MNU] to store the new setting. DTMF LOCK Assuming you have a transceiver with the optional speaker microphone installed and you are carrying it in the holder or bag, you sometimes want to disable the keypad DTMF transmission to avoid the accidental DTMF transmission. In this case, turn the DTMF Lock function ON. 1 Press [MNU] to enter Menu mode. 2 Turn the Tuning control or press [
] to select
]/ [
the Menu No. 14 (DTMF LOCK). 3 Press [sssss] or [MNU]
4 Turn the Tuning control or press [
ON.
]/ [
] to select 5 Press [sssss] or [MNU] to store the setting. When this function is activated, you cannot transmit DTMF tones using the DTMF keypad (including
[MNU]) during the transmission. 2 Release only [MNU], then turn the Tuning control or press [
DTMF memory channel.
]/ [
] to select the desired 3 While still holding [PTT], press [sssss] or [MNU]
to trasmit the DTMF tones. The number stored in the channel scrolls across the display accompanied by DTMF tones from the speaker. After transmission, the frequency display is restored. If you need not confirm the memory channel contents, press [0] to [9] instead of turning the Tuning control or pressing [
] in step 2 to select a channel number. The stored DTMF number will be immediately transmitted. You need not press [sssss] or [MNU] in step 3.
]/ [
32 UTILIZING B-BAND ABOUT B-BAND Usually you can communicate with other amateur radio stations using A-band frequencies for receiving and transmitting. This transceiver also features another receiver in addition to A-band transceiver. The frequency for the B-band appears the bottom part of the display. Although A-band transceiver covers only 144 MHz/ 220 MHz (TH-F6A only)/ 430/
440 MHz amateur radio bands in FM mode, B-band receiver can receive from 100 kHz to 470 MHz in SSB, CW, FM, or AM mode. From 470 MHz to 1.3 GHz, you can also receive in FM or AM mode. In this way, you can monitor 2 different frequencies at the same time. This means that you can listen to a local FM broadcasting station while you are monitoring your club channel at the same time. If one of A-band amateur radio bands is also selected for B-band in FM mode, you can also transmit on the B-band frequency. B-BAND FREQUENCY Since B-band frequency coverage is so wide, the default frequency band, mode, and frequency step size are preprogrammed as shown below. 1 Press [A/B] to select B-band. s icon moves, indicating which band is currently selected. 2 Press [BAND] until the desired frequency band appears. Each time you press [BAND], the frequency band cycles from the last band you selected to upper band frequency. When it reaches to 1.2 GHz band, it goes back to LW band. 3 Turn the Tuning control or press [
a desired frequency.
]/ [
] to tune to Note: You can also select one of the amateur radio band to transmit on the B-band frequency. However, the operating mode must be in FM mode to transmit. n B-band Frequency Coverage dnaB ycneuqerF dnabMA zHk025~zHk001
)A6F-HT(zHM8.1~zHk025
)E7F-HT(zHM17.1~zHk025
)A6F-HT(zHM5.3~zHM8.1
)E7F-HT(zHM5.3~17.1 FH zHM0.4~zHM5.3 zHM0.7~zHM0.4 zHM3.7~zHM0.7 zHM1.01~zHM3.7 zHM51.01~zHM1.01 zHM0.41~zHM51.01 zHM53.41~zHM0.41 zHM860.81~zHM53.41 zHM861.81~zHM860.81 zHM0.12~zHM861.81 zHM54.12~zHM0.12 zHM98.42~zHM54.12 zHM99.42~zHM98.42 zHM0.82~zHM99.42 zHM7.92~zHM0.82 m6 dnabMF dnabriA zHM0.05~zHM7.92 zHM0.45~zHM0.05 zHM0.801~zHM0.45 zHM0.731~zHM0.801 zHM0.441~zHM0.731 m2 zHM0.641~zHM0.441 VTFHV zHM0.471~zHM0.641 zHM0.612~zHM0.471 zHM0.222~zHM0.612 m3.1 zHM0.532~zHM0.222 zHM0.004~zHM0.532 zHM0.034~zHM0.004 zHM0.054~zHM0.034 zHM0.074~zHM0.054 zHM0.608~zHM0.074 zHM0.0031~zHM0.608 mc07 VTFHU mc32 petS zHk1 edoM MA zHk01 MA MA BSL MA BSL MA WC MA BSU MA BSU MA BSU MA BSU MA BSU MF WMF MA MF WMF MF WMF MF zH001
)NOENIF(
zHk52
)A6F-HT(
zHk5
)E7F-HT(
zHk01 zHk001 zHk52 zHk5 5/5.21 zHk zHk5 zHk001 zHk5.21 zHk02
)A6F-HT(
zHk5.21
)E7F-HT(
zHk5.21 zHk5.21 zHk52 zHk5.21 zHk001 zHk52 Note:
u By a default, FINE mode is activated automatically for 1.8 MHz ~
29.7 MHz. u LSB/ USB/ CW mode operation is limited below 600 MHz. u Cellular band is blocked due to government regulations. 35 8 ENHANCED COMMUNICATIONS SELECTING A MODE FOR B-BAND When using B-band, the following receiving mode is available. edomgnivieceR segnarycneuqerfelbaliavA BSU/BSL zHk001 zHM074<f WC MA zHk001 zHM074<f zHk001 zHG3.1<f NMF/MF zHM7.92 zHG3.1<f MFW zHM7.92 zHG3.1<f n LSB/ USB/ AM/ FM/ WFM To select the receiving mode for B-band:
1 Press [VFO]. 2 Press [A/B] to select B-band. 3 Press [BAND] and then turn the Tuning control or press [
]/ [
] to select the desired frequency. 4 Press [MODE] until you select the desired receiving mode. The mode icon cycles FM then goes back to FM. WFM USB LSB AM CW, and Note:
u To select FMN (Narrow FM), access Menu No. 29 and select ON {below}. u LSB, USB, and CW modes can be selected in the frequencies below 470 MHz only. 36 BAR ANTENNA Although the supplied wide-band helical antenna is used for receiving B-band frequencies, due to the size and length limitation, it may not suitable for the low HF band (below 7 MHz) receiption. The transceiver features a built-in bar antenna for the receiption frequency below 7 MHz. The transceiver automatically switches to the bar antenna when you select a frequency below 7 MHz for the B-band. However, you can connect an external antenna to the antenna connector instead. To disable the built-in bar antenna:
1 Press [MNU]. 2 Turn the Tuning control or press [
] to select
]/ [
Menu No. 26 (BAR ANT). 3 Press [sssss], [MNU]. 4 Turn the Tuning control or press [
DISABLE.
]/ [
] to select FINE TUNING MODE When you operate the B-band in LSB, USB, CW, or AM mode, you can turn the FINE Tuning function ON. The Fine Tuning frequency step size can be selected from 50 Hz, 100 Hz (default), or 1000 Hz. n Activating Fine Tuning To activate the FINE Tuning function:
1 Select a frequency (below 470 MHz) on the B-band. Operating mode must be LSB, USB, CW or AM. 2 Press [FINE]. 100 Hz digits appears. 3 Turn the Tuning control or press [
a station.
]/ [
] to tune to Note:
u Fine Tuning functions works only when you operate the frequency below 470 MHz. u You cannot activate the Fine Tuning function on the A-band. u When you change the mode to FM, the frequency will be automatically adjusted to the next available frequency. u While in the Fine Tuning mode, you cannot perform VFO step size change {page xx}, MHz mode {page xx}, and MHz Scan
{page xx}. u When you perform the Visual Scan {page xx}, Information Channel Memory recall {page xx}, Information Channel Scan
{page xx}, VFO mode {page xx}, Memory channel recall {page xx}, Call channel recall {page xx}, or direct frequency entry {page xx}, the transceiver exits the Fine Tuning mode. 8 ENHANCED COMMUNICATIONS n Selecting Fine Tuning Frequency step You can select the Fine Tuning frequency step from 50 Hz, 100 Hz (default), or 1000 Hz. To select the Fine Tuning frequency step size:
1 Select a frequency on the B-band. 2 Press [F], [FINE]. Current frequency step size appears. 3 Turn the Tuning control or press [
]/ [
] to select a desired frequency step from 50 Hz, 100 Hz
(default), or 1000 Hz. 4 Press [sssss] or [MNU] to store the new setting. Note: The Fine Tuning frequency step size reflects all available frequencies for the B-band. 37 OPERATOR CONVENIENCES APO (Auto Power OFF) The TH-F6A/ TH-F7E switches OFF automatically if no keys or controls are pressed or adjusted for 30 minutes (default). 1 minute before the transceiver switches OFF, warning beeps are output for a few seconds and APO appears on the display. You can select the APO time from OFF (disable), 30 (default), and 60 minutes. 1 Press [MNU]. 2 Turn the Tuning control or press [
] to select
]/ [
Menu No. 18 (APO). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
]/ [
] to select the APO time from OFF, 30, or 60 minutes. 5 Press [sssss] or [MNU] to store the setting. Note:
u The APO function works even if the transceiver is scanning. u The APO timer starts counting down the timer when no key presses, no control adjustments, and no command (RS-232C port) sequences are detected. ATTENUATOR The attenuator function is useful when extremely strong signals exist nearby your receiving frequency. When these type of signals exist nearby your receiving frequency, the receiver gain control may be erroneously controlled and overloaded by the strong signals, rather than by the target receiving signal. If this happens, the target receiving signal can be masked and buried by the strong signals. In this case, turn the Attenuator function ON. However, as a side effect, the target signal is also attenuated. You may have to adjust the VOL control to increase the audio output level when it is ON. 1 Press [F], [MONI]. ATT ON appears momentarily on the B-band display and the mode indicator blinks while it is ON. 2 To turn the attenuator function OFF, press [F],
[MONI] again. The mode indicator quits blinking when it is OFF. Note:
u When the attenuator function is ON, both A-band and B-band, are attenuated. You cannot set the attenuator function independently for each band. u ATT function is disabled while scanning. 38 BATTERY SAVER Battery Saver extends the operating time of the transceiver. It becomes automatically active when the squelch is closed and no key is pressed for more than 10 seconds. To reduce the battery consumption, it shuts the receiver circuit OFF for the programmed time then momentarily ON to detect the signal. To program the receiver shut-off period for the battery saver:
1 Press [MNU]. 2 Turn the Tuning control or press [
] to select
]/ [
Menu No. 17 (BAT SAVER). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
]/ [
] to select the receiver shut-off period from OFF, 0.2, 0.4, 0.6, 0.8, 1.0 (default), 2.0, 3.0, 4.0, and 5.0 seconds. 5 Press [sssss] or [MNU] to store the setting. Note: Longer period, more you can save the battery consumption. However, more chances of missing the signal. BATTERY REMAINING You can confirm the remaining Ni-ion battery capacity using this function. To confirm the Ni-ion battery remaining capacity:
Press [F], [LOW]. Battery remaining indicator appears.
: more than 70 %
: 40 % ~ 70 %
: less than 40 %
: needs recharging Note: When DC IN jack is connected to the DC source (13.8 V DC), CHARGING (charging the Ni-ion battery) or STANDBY (charging has completed) appears. BEEP FUNCTION The Beep function provides you confirmation of entry, error status, and malfunctions of the transceiver. We recommend you leave it ON in order to detect erroneous operatins and malfunctions. However, to turn the beep function OFF:
1 Press [MNU]. 2 Turn the Tuning control or press [
] to select
]/ [
Menu No. 19 (KEY BEEP). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
OFF.
]/ [
] to select 5 Press [sssss] or [MNU] to store the setting. The transceiver generates the following warning beeps even if the beep function is turned OFF. DC voltage error {page 2}. PLL circuit malfunctions. Note: A beep output level is linked the VOL control position. BEAT SHIFT Since the transceiver uses a microprocessor to control various functions of the transceiver, the CPU clock oscillators harmonics or image may appear on some spots of the receiving frequencies. In this case, turn the Beat Shift function ON. 1 Press [MNU]. 2 Turn the Tuning control or press [
] to select
]/ [
Menu No. 25 (BEAT SHIFT). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
ON.
]/ [
] to select 5 Press [sssss] or [MNU] to store the setting. DISPLAY CONTRAST You can adjust the LCD contrast level from 1
(weakest) to 16 (strongest) by accessing Menu No. 16 (CONTRAST). A default level is 8. 1 Press [MNU]. 2 Turn the Tuning control or press [
]/ [
] to select Menu No. 16 (CONTRAST). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
the LCD contrast.
]/ [
] to adjust The relative contrast level appears in a bar-graph. 5 Press [sssss] or [MNU] to store the setting. FREQUENCY STEP SIZE Choosing the correct frequency step size is essential in order to select your exact receive frequency using the Tuning control or pressing [
select your desired frequency step size from:
5 kHz, 6.25 kHz, 8.33 kHz (118 MHz band only), 9 kHz (AM broadcasting band only) , 10 kHz, 12.5 kHz, 15 kHz, 20 kHz, 25 KHz, 30 kHz, 50 kHz, 100 kHz. The default step size for the amateur radio bands are as follows.
]. You can
]/ [
15 OPERATOR CONVENIENCES dnaB dnab-A dnab-B oidarruetamA dnab zHM441 zHM022 zHM044/034 zHM441 zHM022 zHM044/034 zHG2.1 A6F-HT zHk5 zHk02 zHk52 zHk5 zHk02 zHk52 zHk52 E7F-HT zHk5.21 zHk52 zHk5.21 zHk5.21 zHk52 zHk52 For B-band, refer to the page 35 for the default frequency step size for other frequency bands. The transceiver stores the frequency step size parameter for each band independently. You can also further fine tune the frequency in LSB, USB, AM, CW modes on the B-band. Refer to FINE tuning function
{page 36}. Note: If you change the frequency step size that does not match the current operating frequency, the transceiver automatically adjust the frequency that matches new frequency step size. LAMP You can illuminate the transceiver display by pressing
[LAMP]. Approximately 5 seconds after releasing
[LAMP], the light goes OFF if no other key is pressed. Pressing any key other than [LAMP] while the display is lit, restarts the 5-second timer; pressing
[LAMP] turns OFF the light immediately. To keep the light ON continuously, press [F], [LAMP]. The light remains ON until you press [F], [LAMP]. LOCK FUNCTION Lock function disables the most of keys to prevent you from accidentally activating a function or changing the current settings. Press [F] (1 s) to toggle Lock function ON or OFF. appears when this function is ON. However, the following keys are not locked:
[LAMP], [MONI], [SQL], [PTT], [F] (1 s), [
[F] then [LAMP].
], and Note: The Tuning control is also locked. To unlock the Tuning control while the Lock function is ON, turn the Tune Enable function ON. n Tune Enable Even if the Lock function is ON, you sometimes want to turn the Tuning control to change the frequency. In this case, turn this function ON. 1 Press [MNU]. 2 Turn the Tuning control or press [
]/ [ ] to select Menu No. 7 (TUNE ENABLE). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
ON.
]/ [ ] to select 5 Press [sssss] or [MNU] to store the setting. 39 15 OPERATOR CONVENIENCES MICROPHONE PF KEYS (OPTIONAL) If you have an optional SMC-33 or SMC-34 speaker microphone, you can access many transceiver settings without using transceiver keys or controls. The 1, 2, and 3 keys located on the top of the microphone are programmable with the transceiver key (or key combination) function. The default assignment functions are as follows.
[1]: A/B
[2]: VFO/ MR
[3]: CALL (TH-F6A)/ 1750 Hz (TH-F7E) Note:
u Turn the transceiver OFF before connecting the optional speaker microphone. u If the LOCK switch on the rear of the microphone is ON, you must move the switch to OFF position to program the keys. 1 Press one of the following key combinations to re-
program the keys on the speaker microphone. Press Mic [1]+ [
] to re-program Mic [1] key Press Mic [2]+ [
] to re-program Mic [2] key Press Mic [3]+ [
] to re-program Mic [3] key 2 Press a key or key combination you want to assign to the function key.
]YEK[
]YEK[+]F[
VER f>-<NM zHM ENIF OFV RM LLAC zH0571 PMAL INOM WOL DNAB B/A OFNI LQS LAB ENOT NI.NM TUO.L PETS V>M NI.M NI.C 1 PMAL TTAB EDOM LAUD LAUSIV XOV IRP LES.T TFIHS 1 The light stays ON until you press the key again. MONITOR When you are receiving while the squelch function is ON, weak signals may become intermittent. Or, if the CTCSS or DCS function is ON, you may want to disable the squelch function temporarily to monitor the current channel activities. In these cases, use the Monitor function to disable the squelch function temporarily. To activate the Monitor function:
1 Press and hold [MONI]. The speaker is unmuted and you can monitor the signals. 2 Release [MONI] key to return to normal operation. 40 NARROW BAND FM OPERATION By a default, if you select FM mode, the transceiver operates in normal FM deviation ( 25kHz) mode for both transmission and receiption. However, you can operates the transceiver in narrow band FM deviation
( 12.5kHz) mode. To operate the narrow band FM:
1 Press [MNU]. 2 Turn the Tuning control or press [
] to select
]/ [
Menu No. 29 (FM NARROW). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
ON.
]/ [
] to select 5 Press [sssss] or [MNU] to store the setting. When the narrow band FM operation is ON, FMN appears instead of FM. Note: When you select Menu No. xx ON (9600 bps), the A-band operating mode returns to normal FM mode temporarily POWER-ON MESSAGE You can change the greeting message when the transceiver is turned ON. To change the message:
1 Press [MNU]. 2 Turn the Tuning control or press [
]/ [
Menu No. 15 (PWR-ON MSG).
] to select 3 Press [sssss] or [MNU]. The current message and entry cursor appears. 3 Turn the Tuning control or press [
]/ [
] to select the first character. You can enter alphanumeric characters plus special ASCII characters. See the table below for available characters. 4 Press [sssss]. The cursor moves to the next digit. 5 Repeat steps 3 and 4 to enter up to 8 digits. Pressing [sssss] after selecting the 8th digit completes the programming. To complete programming after entering less than 8 digits, press [sssss] twice. Press [ttttt] to move a cursor backward. Pressing [F] deletes a character at the cursor position. You can also use the keypad to enter alphanumeric characters in step 3. For example, each press of
[2] selects entry as a, b, c, 2, A, B, C, then a. Press
[0] to select space or 0. Refer to page 17 for the available characters and control keys. PROGRAMMABLE VFO If you want to limit the operating frequencies within a certain range, program the upper and lower frequency limits to the program VFO pamameters. For example, if you select 448 MHz for the lower limit and 449 MHz for the upper limit, the tunable range will be limited from 448.000 MHz to 449.995 MHz. 1 Press [A/B] to select A-band. 2 Press [VFO]. 2 Press [BAND] until you select the desired amateur radio band to configure the programmable VFO frequency range. 3 Press [MNU]. 4 Turn the Tuning control or press [
]/ [
] to select Menu No. 4. The current programmable frequency range for the band appears. 5 Press [sssss] or [MNU]. 6 Turn the Tuning control or press [
the lower limit frequency in MHz.
]/ [
] to select 7 Press [sssss] or [MNU] to store the lower limit frequency. The cursor moves to right and the upper limit frequency blinks. 8 Turn the Tuning control or press [
the upper limit frequency in MHz.
]/ [
] to select 7 Press [sssss] or [MNU] to store the upper limit frequency. Note:
u You cannot program the 100 kHz or lower digit. u The upper limit frequency varies depending on the selected frequency step size. SINGLE BAND OPERATION If you do not want to use A and B-band receiver at the same time, you can turn A or B-band receiver OFF. 1 Press [A/B] to select the band you want to operate. 2 Press [F], [A/B]. The frequency of the selected band appears in large font and the other band is turned OFF. 15 OPERATOR CONVENIENCES 3 To return to normal dual band operation, press [F],
[A/B] again. TIME-OUT TIMER The Time-out Timer limits the time of each transmission. The built-in time-out timer in the transceiver limits each transmission time for a maximum of 10 minutes. It is necessary to protect the transceiver from the thermal damage. You cannot turn this function OFF. TONE ALERT Tone Alert provides an audible alarm when signals are received on the frequency you are monitoring. In addition, it shows the number of hours and minutes elapsed after signals were received. If you use Tone Altert with CTCSS or DCS, it alarms only when a received CTCSS tone or DCS code matches the tone or code yo selected. 1 Select your desired frequeny or memory channel. 2 Press [F], [ENT]. A bell icon appears when Tone Alert function is ON. When a signal is received, an alarm soundsfor 10 seconds and the bell icon stars blinking. Pressing the PTT switch while the bell icon is blinking switches Tone Alert function OFF. When 99 hours and 59 minutes pass after a signal is received, counting stops. Each time a new signal is received, the elapsed time resets to 00:00. Note:
u While Tone Alert is ON, there is no speaker output when a signal is received. To monitor the signal, press and hold [MONI]. u When Tone Alert is ON, APO does not turn the power OFF. u When Tone Alert is ON, you can use only the following functions.
[LAMP], [MONI], [SQL], [A/B], [F] then [LAMP], [F] then [ENT]. TX INHIBIT You can inhibit the transmission to prevent unauthorized individuals from transmitting, or to eliminate the accidental transmissions while carrying 41 15 OPERATOR CONVENIENCES the transceiver. 1 Press [MNU]. 2 Turn the Tuning control or press [
Menu No. 8 (TX INHIBIT). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
ON.
]/ [
] to select
]/ [
] to select 5 Press [sssss] or [MNU] to store the setting. TX INHIBIT! appears if you press [PTT] while the TX Inhibit is ON. L TX POWER You can change the transmission output power by pressing [LOW]. Each time you press [LOW], the icon cycles H EL, and then goes back to H. The output power varies depending on the battery type and operating voltage. When the transceiver operates with the power from the DC IN jack at 13.8 V DC, it produces the maximum output power. The table below is approximate output power when the transceiver operates with different types of battery or DC power source. tuptuO leveLrewoP yrettaB epyT dnaB rewoPtuptuO
).xorppa(
A6F-HT E7F-HT 41-TB
)V0.6(
zHM441 zHM022 W7.1 W0.2 A/N zHM044/034 W5.2 zHM441 zHM022 zHM044/034 zHM441 zHM022 zHM044/034 zHM441 zHM022 zHM044/034 zHM441 zHM022 zHM044/034 zHM441 zHM022 zHM044/034 zHM441 zHM022 zHM044/034 zHM441 zHM022 zHM044/034 zHM441 zHM022 zHM044/034 H
)hgih(
L24-BP
)V4.7(
NICD
)V8.31(
41-TB
)V0.6(
L
)wol(
L24-BP
)V4.7(
NICD
)V8.31(
41-TB
)V0.6(
L24-BP
)V4.7(
NICD
)V8.31(
LE cimonoce(
)wol 42 VOLUME BALANCE While you are receiving A and B-bands at the same time, you may sometimes feel that audio output on either band is too loud. You can adjust the volume balance level of the bands. 1 Press [BAL]. The balance scale and blinking cursor appear. 2 Turn the Tuning control or press [
]/ [
] to change the volume balance level of the bands. A-band Max Max B-band Mute Att Max Max Att Max Mute Max Max: Maximum, Mute: Muted, Att: Attenuated 3 Press [sssss] or [MNU] to store the setting. VOX (VOICE-OPERATED TRANSMIT) VOX eliminates the necessity of manually switching to the transmit mode each time you want to transmit. The transceiver automatically switches to transmit mode when the VOX circuitry senses that you have begun speaking into the microphone. When using VOX, develop the habit of pausing between thoughts to allow the transceiver to drop back to receive mode briefly. You will then hear if anybody wants to interrupt, plus you will have a short period to gather your thoughts before speaking again. Your listeners will appreciate your consideration as well as respect your more articulate conversation. VOX can be switched ON and OFF independently for CW and the other modes, excluding FSK. 1 Press [F], [SQL]. VOX appears. To exit the VOX mode, press [F], [SQL] again. n Microphone Input Level To enjoy the VOX function, take the time to properly adjust the gain of the VOX circuit. This level controls the capability of the VOX circuit to detect the presence or absence of your voice. 1 Press [MNU]. 2 Turn the Tuning control or press [
access Menu No. 21 (VOX GAIN).
] to
]/ [
3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
select the ON.
]/ [
] to 5 Press [sssss] or [MNU] to store the setting. 6 While speaking into the microphone using your 15 OPERATOR CONVENIENCES normal tone of voice, adjust the setting (default is 4) using the Tuning control or press [
]
until the transceiver reliably switches to transmit mode each time you speak. The selectable gain range is from 0 (least
]/ [
sensitive) to 9 (most sensitive). The setting should not allow background noise to switch the transceiver to transmit mode. Note: The VOX gain level can be adjusted even if VOX is switched OFF or while you are transmitting. n Delay Time If the transceiver returns to receive mode too quickly after you stop speaking, your final word may not be transmitted. To avoid this, select an appropriate delay time that allows all of your words to be transmitted without an overly long delay after you stop speaking. 1 Press [MNU]. 2 Turn the Tuning control or press [
select Menu No. 22 (VOX DELAY).
] to
]/ [
3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
] to select the desired delay time from 100/ 200/
300/ 500 (default)/ 1000/ 1500/ 3000 ms. 5 Press [sssss] or [MNU] to store the setting.
]/ [
n VOX on Busy You can configure the transceiver to enforce the VOX transmission even if the A and/or B-band receiver is receiving the signals. 1 Press [MNU]. 2 Turn the Tuning control or press [
] to
]/ [
select Menu No. 20 (VOXonBUSY). 3 Press [sssss] or [MNU]. 4 Turn the Tuning control or press [
]/ [
] to select ON. To supress the VOX transmission when the transceiver is receiving the signals, select OFF. 5 Press [sssss] or [MNU] to store the setting. 43 WIRELESS REMOTE CONTROL (TH-F6A ONLY) If you also have a KENWOOD multi-band mobile transceiver, you can control one of its bands by sending DTMF tones from this handy transceiver. You will find this function useful when you want to control your mobile transceiver from a location outside your vehicle. Note:
u You can remotely control only the mobile transceivers that have both the DTSS and Remote Control functions. u The FCC rules permit you to send control codes only on the 440 MHz band. PREPARATION Let us assume the 144 MHz band of the mobile transceiver will be controlled. On the handy transceiver:
1 Press [PTT]+[VFO]+[
]. The current secret access code number appears. The default is 000. 2 Press a numeric key 0 to 9 to enter a 3-digit secret number. You can also turn the Tuning control or press
] to select each digit. Press [sssss] ([ttttt])
[
to move the cursor to the next (previous) digit. 3 When the cursor on the most right position, press
]/ [
[sssss] to complete the setting. 4 Select the 440 MHz band. 5 Select the transmit frequency. 6 Turn the transceiver power OFF. 7 Press [PTT]+[MR]+[
]. The transceiver enters Remote Control mode. MOBILE CTRL appears. To exit Remote control mode, repeat steps 6 and 7. 10 Make the transceiver enter Remote Control mode. For the method, refer to the instruction manual for the mobile transceiver. CONTROL OPERATION When in the Remote Control mode, the keys of the transceiver will function as below. Each time you press a key, the transceiver will automatically enter transmit mode and send the corresponding command to the mobile transceiver. 1 2 3 NOVER NOENOT NOSSCTC 4 5 6 A TNE B FFOVER FFOENOT FFOSSCTC LESENOT 7 LLAC NWOD 8 OFV 0 WOL 9 RM C
)NOPER(
D PU
)FFOPER(
1 TM-V7A/ TM-D700A: REV ON/ OFF Other mobile transceiver: TONE ALERT ON/ OFF 2 Switches Repeater function ON/ OFF if the mobile transceiver support this function. To change the transmit/ receive frequency:
[VFO] [ENT] [0] ~ [9] (enter the necessary digits) [ENT]) or [VFO] [UP]/ [DOWN]
To recall a memory channel:
[MR] [ENT] [0] ~ [9] (enter the necessary digits)
[ENT] or [MR] [UP]/ [DOWN]
To change the tone (or CTCSS) frequency:
[TONE SEL] [0] ~ [9] (enter 2 digits; ex. [0], [5])
[TONE SEL]
Refer to the Tone frequency table on your mobile transceiver for the Tone number. Your mobile transceiver may require you to first activate the Tone or CTCSS function. It may also allow you to program a separate tone and CTCSS frequency. Check the instruction manual for the mobile transceiver. On the mobile transceiver:
8 Program the DTSS code on the UHF band as the secret number. Select the same number as you selected in step 2. For the programming method, refer to the instruction manual for the mobile transceiver. 9 Select the receive frequency on the UHF band. Mate this frequency with the transmit frequency on the handy transceiver. 47 OPTIONAL ACCESSORIES BT-13 Drycell Battery Case EMC-3 Clip Microphone HMC-3 Headset with VOX/ PTT HMC-5 Headset HS-9 Earphone PB-42L Li-ion Battery Pack PG-2W DC Cable PG-3J Filtered Cigarette Lighter Cable SMC-32 Speaker Microphone SMC-33 Remote Control Speaker Microphone SMC-34 Remote Control Speaker Microphone (with VOL control) VC-H1 Interactive Visual Communicator 52
This product uses the FCC Data API but is not endorsed or certified by the FCC