8406317-24GTX 1/24 R/C Jet Panther User manual

im NO.: 84061 / 84063 / 84064 / al 2 e707 Ye 7 Toes yo INSTRUCTION

>> MANUAL Kenmore necumreeTs

-RC Vehicle (Vehicle) x 1

-RC Transmitter (Transmitter) x 1

-Instruction Manual x 1 Pern ae Pett RC Transmitter x 1 RC Vehicle x 1 Battery Precaution 8. Be sure to insert batteries with correct polarities and always follow the battery 1. Alkaline batteries are recommended to be used manufacturer's instructions 2. Only batteries of the same or equivalent type as recommended are to be used 9. Remove all batteries from the Vehicle and Transmitter when not in use 3. Do not mix alkaline, standard or rechargeable batteries 10. Exhausted batteries are to be removed from the product 4. Do not mix old and new batteries or different type of batteries 11. The supply terminals are not to be short-circuited 5. Non-rechargeable batteries are not to be charged 12, Dispose of batteries property. Do not dispose the batteries in fire it may 6. If rechargeable batteries are to be used, they are only to be charged by adult cause them to explode or leak causing injury or damage 7. Rechargeable batteries are to be removed from the product before they 13. Battery installation and removal must only be done by adult are charged EEEX@ dee Installation For Vehi ig. 1 and Fig. 2) For Transmitter (Fig. 3 and Fig. 4) Sere nee Ree es Unscrew the screw on the battery cover Open the battery cover Re ne tee OLE epee een De Se

(Open the battery cover Install 2 new 1.5V AAA batteries with correct polarities (+/-) BeN-

ON:

Install 3 new 1.5V AAA batteries with correct polarities (+), as shown inside the battery compartment Close the battery cover Tighten the screw on the battery cover as shown inside the battery compartment Close the battery cover Tighten the screw on the battery cover oe Fig. 2 Nee sid [eed AK Li:

1. Tum on the Vehicle 2. Hold the Signal Match Button for 4 second then the Transmitter signal ight will fash for 6-7 second. When the Transmitter signal light keep on will show the matching, 3. After the wheels of the Vehicle turn left and right and the LED light of the Transmitter stops flashing, the binding process completed for playing. 4. Ifit cannot complete within 8 seconds, please tum off both Vehicle and Transmitter and re-start the binding process. 5. When the binding process is done, whenever switching the Vehicle and Transmitter on and off, it searches for the code that it memorized, and will only lock on to the Transmitter signal containing that code. 6. Please tum off both Vehicle and Transmitter and re-start all binding process if changing to another 2.4GHz Transmitter for playing. DCeaouaoe areal 3. Use the Accelerator Trigger to drive the Vehicle Forward, Stop and Backward 1. Switch ON the Vehicle. Pond 4. Ifthe vehicle does not run in straight line, adjust the Direction Adjustment on the Vehicle chassis (Fig.1) Play on smooth surface to have the optimum performance Remember to switch OFF the power of the Vehicle after playing The optimum control range is up to 25m outdoor Non a Fe Sy ip eC eee saree

| Keep driving forward rapidly then switch to backward for the braking action. When the trigger i of the Transmitter retums to the center position, push it again for the backward action. Performance Tips 4. Donot drive on gress, dit, sand, dusts, carpet or go through water Saad 2 Bonotdive ivindy or rainy weather eee a 3. Avoid det mpact the Venile with obstacles Pa et ree ete eee CoE 4 Stitch OFF the power when notin use to prevent damage of Vehicle and Transmitter (amaneneayrmamerseet

{due to leakage of electrolyte from batteries zit 5, Bdnoveal bateres fo ine hice and Transmit hen not se fr long period |Salad

: Keep fnogs, ta anos coving avay for wes ransmiterto child to play 6 operaing range can be affected by a varel of factors ihe once Fanpe cons peor ere Ot SL cia a ee Interferenge fom otner tens tat emit radio frequency signals Cos 8. Outdoor usage is recommended in order to get opimum congo range helene Creer Tee ee eve ety 8: Recommend to play the vehicle on a clean and smooth surface Pars 10, Gane baler comparment make sue tise om isto preventpoor APE ee eee ead contac of batteries FCC label compliance statemen This device complies with part 15 of the FCC rules. Operation is subject tothe following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instalation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to ty to correct the interference by one or more ofthe folowing measures:

~ Reorient or relocate the receiving antenna

~ Increase the separation between the equipment and receiver

~ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

= _ Consul the dealer or an experienced radio/TV technician for help

\Waming: Changes or modifications to this unt not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RSS.210 Compliance Statement:

This device complies with Industry Canada licence-exempt RSS standards). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved forthe transmitter by Industry

(Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (ei.rp.) is not more than that necessary for successful communication. Declaration of Conformity The product isin conformity with the requirement of EU Directive 2014/53/EU. Environmental notes:

The whole product also does not belong to household waste at the end of the produc life Frequency band: 2410 - 2475 MHz You can retum it at collection points for the recyciing of electronic and electronical instruments Maximum radio frequency The symbol on the item, instruction manual, hangtag or packing is showing this clearly. B power transmitted: <0 dBm Materials should be recycled according to their respective markings. Recycling of old devices or other re-use of materials contained therein represents an important

(contribution to environmental protection. Pease ask at your local community for the correct collection point. @

Disposal of batteries Batteries should not be disposed of in the household waste. As the consumer you are legally obliged to retum batteries containing harmful substances and all other used batteries. You can hand in your old Pana russe oe Sf Sen ees eee ney Gama harmful substances: KIDZTECH TOYS MANUFACTURING LTD. Pb=Battery contains lead Room 1201,12F, intr-Continental Plaza, 34 Granvillo Road, TST East, Hong Kong,

(Cd=Battery contains cadmium Hg=Battery contains mercury Tol: (852) 27218868 info@kidztech not Maden China hipilwewidztech net