CGR1S2 BLT5 Manual

Certification Exhibit FCC ID: R7PCGR1S2 FCC Rule Part: 15.247 ACS Project Number: 12-0230 Manufacturer: Landis+Gyr Technology, Inc. Model: BLT5 Manual 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Assembly Instructions, Kit, BLT5 Transceiver, MCC, 97-1828 Revision History ECO Revision Date Author Comments ECO-051889 AA ECO-052962 AB 8/20/2012 Robert Johnson Initial Release 4/10/2014 Robert Johnson Modifcation to initial Release, added FCC statement PROPRIETARY INFORMATION NOTICE: THIS DOCUMENT CONTAINS TRADE SECRETS AND CONFIDENTIAL INFORMATION OF LANDIS+GYR AND SHALL NOT BE DUPLICATED IN WHOLE OR IN PART OR USED OR DISCLOSED FOR ANY PURPOSE OTHER THAN THAT APPROVED BY LANDIS+GYR. Assembly Instructions, Kit, BLT5, MCC 97-1828 Rev AB Page 2 of 4 CONTENTS 1 INTRODUCTION ..................................................................................................................................................................3 2 REMOVING THE EXISTING BLT3 TRANSCEIVER FROM THE MCCS ENCLOSER...........................................3 3 RE-INSTALLING THE UPDATED LAN/WAN BRACKET ASSEMBLY CONTAINING THE UPDATED BLT5 TRANSCEIVER UNIT INTO THE MCC ENCLOSER..........................................................................................3 4. FINAL INSTALLATION......................................................................................................................................................4 5. FCC.4 PROPRIETARY INFORMATION NOTICE: THIS DOCUMENT CONTAINS TRADE SECRETS AND CONFIDENTIAL INFORMATION OF LANDIS+GYR AND SHALL NOT BE DUPLICATED IN WHOLE OR IN PART OR USED OR DISCLOSED FOR ANY PURPOSE OTHER THAN THAT APPROVED BY LANDIS+GYR. Assembly Instructions, Kit, BLT5, MCC 97-1828 Rev AB Page 3 of 4 1 Introduction 1.1 All MCCs updated in the field requiring replacement of their original BLT3 transceiver to the newly designed BLT5 transceiver must also be retro-fitted per the guidelines specified in this procedure. The MCC field update consists of removing the original BLT3 transceiver, and replacing it with the newly redesigned BLT5 transceiver. After the new BLT5 transceiver has been installed you will also need to install a new FCC label, part number 23-1401. The new FCC label should be placed on the MCCs exterior where it will be highly visible. The new FCC, BLT5 Retrofit label can be found in the MCC retro-fit kit, designated as follows: Kit, BLT5 Transceiver, MCC kit, Landis part number 45-1828. The bill of materials is listed below. item_number 23-1127 90-1002 97-1828 23-1401 26-1828 Kit, BLT5 Transceiver, MCC Part number 45-1828 item_name LABEL,BLANK,UTILITY ID BAG, 9"X12"X.004 CLEAR POLY BAG WITH ZIPPER Assembly Instructions, Kit, BLT5 Transceiver, MCC Label, FCC, BLT5 Retrofit T/A, BLT5 Transceiver, MCC quantity 1 2 1 1 0 1 1 2. Removing the existing BLT3 transceiver from the MCCs enclosure 2.1 Refer to Landis document part number : 97-2350, MPI, REPACKAGED ASSEMBLY INSTRUCTION, section 3.0 through section 3.8 for details on how to remove the exisiting BLT3 transceiver module. 2.2. To remove the existing, original BLT3 transceiver, disconnect the antenna cables P/N: 19-0014, LAN/WAN Radio Power Cable assembly P/N 19-2351, and the LAN Data cables P/N: 19-2352. 2.3. Losen the LAN/WAN assembly backets machine-screw Hex-nuts. The stated Hex-nuts are used to hold down the LAN/WAN assembly to the inside of the MCC enclosure, then remove the LAN/WAN assembly from the MCC enclosure. Once the LAN/WAN assembly has been pulled from the MCC inclosure, losen the hex-nuts used to hold down the original BLT3 transceiver assembly to the LAN/WAN assembly mouting bracket, pull the BLT3 transciever for the LAN/WAN mounting bracket assembly, and replace the orignal BLT3 transceiver will the newly redesigned BLT5 transceiver assembly. 3. Re-installing the updated LAN/WAN bracket assembly containing the updated BLT5 transceiver unit into the MCC encloser 3.1 Once you have re-fitted the BLT5 transceiver on the LAN/WAN mounting bracket assembly, re-

torque the mounting Hex-nuts used to hold the BLT5 assembly to the LAN/WAN mounting bracket, then, re-install the LAN/WAN mounting bracket assembly inside the MCC enclosure, and re-torque the LAN/WAN mounting brackets Hex-nuts. The stated Hex-nuts are used to mount the LAN/WAN bracket assembly down to the inside of the MCC enclosure. 3.2 On completion of re-installing the LAN/WAN bracket assembly containing the newly added BLT5 transceiver you can re-connect the antenna cables P/N: 19-0014, LAN/WAN Radio Power Cable assembly P/N 19-2351, and the LAN Data cable P/N: 19-2352, PROPRIETARY INFORMATION NOTICE: THIS DOCUMENT CONTAINS TRADE SECRETS AND CONFIDENTIAL INFORMATION OF LANDIS+GYR AND SHALL NOT BE DUPLICATED IN WHOLE OR IN PART OR USED OR DISCLOSED FOR ANY PURPOSE OTHER THAN THAT APPROVED BY LANDIS+GYR. Assembly Instructions, Kit, BLT5, MCC 97-1828 Rev AB Page 4 of 4 4. Final Installation 4.1 From your MCC retro fit kit contained in a 9x 12 zip lock bag, remove the new FCC, BLT5 Retrofit label, part number 23-1401. Next remove the labels non-stick backing paper to expose the adhesive side of the lablel then stick the new FCC label on the outside of the MCCs enclosure. The label should be placed on the enclosures painted exterior bottom where it will be highly visible. 4.1 The MCC may be returned to service. 5. FCC This product shall comply with the FCC requirements listed in United States CFR Title 47, Part 15.109, 15.209 and15.247. The FCC tests should be performed with the meter module in the configuration s close to the typical field configuration as possible. PROPRIETARY INFORMATION NOTICE: THIS DOCUMENT CONTAINS TRADE SECRETS AND CONFIDENTIAL INFORMATION OF LANDIS+GYR AND SHALL NOT BE DUPLICATED IN WHOLE OR IN PART OR USED OR DISCLOSED FOR ANY PURPOSE OTHER THAN THAT APPROVED BY LANDIS+GYR.